Basic Initial Cisco Switch Configuration
Тәжірибелік нұсқаулар және стиль
This video will guide you through the basic configuration of a Cisco switch. The model used is a 3560 layer 3 switch. To keep this video from going too long, this video will only cover the basics so that you can access the switch over the network and no longer need a console cable to finish configuring it. This video covers the following areas:
- What's needed (i.e. cables)
- Physical connections
- Network Topology
- Discuss Different Modes (i.e. privilege exec mode)
- Set Hostname
- Set IP Address for VLAN
- Set Password for VTY
- Set Enable Password
- Set service password-encryption
Please let me know if you have any comments or questions and I will do my best to help. If you found this video helpful, please like and subscribe. Thanks!
Пікірлер: 31
Watching in 2023. Thanks a million!
I liked your tutorial, you sound like a regular guy helping techs with your experience, thanks. I use the usb to serial port adapter as my mobo doesn’t have serial port access. Console away I am 😁
Thanks so much man, you actually explained what's what so I really appreciate it! Most of the videos on basic switch configs people just run through commands but for beginners it's hard to understand what he's doing.
@itsallgeektome7764
7 жыл бұрын
I appreciate the comment and am glad that you found it useful :-)
@janaybhido
3 жыл бұрын
can you help us to configure our switches we can pay your time also thanks
@inspiringminds7284
3 жыл бұрын
Read a book first!
@inspiringminds7284
3 жыл бұрын
@@janaybhido I will help you set your switches up for a fee.
This video is sooooo helpful. Thanks a lot. God bless you.
Very helpful, thank you! 👍🏻
Very clear turorial...thank you.👍
Really enjoyed the video and straight forward explanation.
@janaybhido
3 жыл бұрын
can you help us to configure our switches we can pay your time also
Thank you. I just installed packet tracer and this video helped get me started.
@janaybhido
3 жыл бұрын
can you help us to configure our switches we can pay your time also. thanks
Mate brilliant, i am just setting up my first cisco 3560 switch and this is gold. at 4:34 man actually said pound sign to # lol ... i was like what lol. but this is great education for me. thanks.
Thank you Great walk through, talk through. Your video enabled me to successfully setup a 3560 switch, with my Autonomous AP, and give the devices a second life. Especially the Telnet capability
very nice explanations....thanks for support
Good video, very helpful for beginners like me.
@janaybhido
3 жыл бұрын
can you help us to configure our switches we can pay your time also
@mrGentox
3 жыл бұрын
@@janaybhido you should try here community.cisco.com
Hello, I put cisco 2960 and I run it after connection with consulta cable waited ,but switch> did not appear
Thanks
When I type the "enable" command I get (Unknown cmd: enable) Can anyone tell me why I am not able to change to privileged mode "switch#" prompt when I type enable? What would cause it to not recognize the enable command?
Did you forget about the serial port properties? From the official Cisco Installation page: Configure the baud rate and character format of the PC or terminal to match the console port default characteristics: 9600 baud 8 data bits 1 stop bit No parity None (flow control)
Thanks 😊. Can you explain, What is mean 5 in secrets password??, I mean your output "enable secret 5 %$%$5464", Thanks 😊. in 12:20. I hope my question Clearly.
It's a great video but some of words you pronounce are not too clear (fast).
@janaybhido
3 жыл бұрын
can you help us to configure our switches we can pay your time also
@tahersadeghi6773
3 жыл бұрын
@@janaybhido Yes I can help you.
Sorry sir but its really hard to understand you, could you speak more clearly? Also the way you said '3560 switch' was really confusing.
“In this video I’m going to...” unbearable.