This was the 100% perfect information I was looking for! Even used the exact tools I have.

@5thStreetFab

6 жыл бұрын

Right on bud I'm glad to hear it!

This was exactly what I was looking for as I'm building a support frame for my tool drawer. Great series 👌

Great video. The advice on cutting angle iron was just what I was looking for!

Nicely done. I like how you showed a few different cuts. I will try your techniques the next time I'm welding angle iron with my everlast welder.

Good information and to the point. Great job.

Recently started welding as a hobby and your video really helps

@5thStreetFab

6 жыл бұрын

diondamian20@yahoo.com thanks you. I'm glad they've been helping!

I taught this young man everything he knows about welding and metal fab. I can't wait to see ur next youtube video little johnny

Thanks for the attention to small details. Plenty of How to Weld videos out there but yours is the only one that gives the information on what the hell to weld and how to set up for it. Far more useful!

@5thStreetFab

6 жыл бұрын

thank you thats what im hoping for!

@Goalsplus

6 жыл бұрын

5th Street Fab Shop . You're a good man. When the haters, the do nothing know it alls who think the world owes them a living, start dropping critical remarks with, of course, no solid useful information on how to do anything better, please do all the good positive and worthwhile people I see in comments a favour and completely ignore the negative. Too many KZreadr lose their drive and enthusiasm listening to them. Thanks for the reply.

@5thStreetFab

6 жыл бұрын

great tip! I will try my best!

Good point on the bandsaw clamp, top tip there.

Thanks for your knowledge and sharing your experience 😊

Thanks buddy! Lookin for some tips and found ur site! Cool vid

I'm making a frame soon and I was going to cut a miter in the angle iron with a grinder but I like the coping method, easier and hopefully will hold better as a foot frame from my Anvil.

You are great my brother good job

My hoarding of bedrails is going to come to fruition. Was looking for some ideas.

so useful and so helpful thanks a lot bro

great job thank you

thx, good video on some simple and tidy methods...pump up the volume a little though.

Good Stuff Evan.!!

Thank you for sharing you saved my ass. Im a Hvac guy not a shop guy. They want me to fab this aluminum angle frame. Its got to sit flat so I either need to miter or notch. Going with notch. Hey @ 6:52 the word your looking for is True Length. The true length will change depending on the degree of the angle. Have a good 1 bro.

@5thStreetFab

3 жыл бұрын

Thanks bud im glad it helped you!

Thank you 🙏

Great tips! But I always cut angle iron with the angle side up for (upside down V) of course just cutting to length not miters......I found it’s easier on the blade!

That was the angle of the dangle I sure like your saw

good job

Very Nice Frame. How Would You Add Three of These (same Dimension)To Fit a Three Level ,Top, Bottom and Center To a Cart with wheels?

Got any tips on using a powerplasma cutter?

Hello there, can you please share the jig you used when cutting with band saw in a vertical position. Thanks

The noise at the 6:04 mark is a wonderful noise that is sooooo freaking annoying at the same time!!! It is definitely a love-hate relationship!!! Lmao.

Thanks for the vid. I "invented" the square-stock method myself just recently and it seems to work fine, but I'm on here because every piece of info I can find online (and in the saw manual) says that you should only cut angle iron when the corner is pointing up. But no one ever says why--it's just one of those rules that's passed on but never explained. Does anyone out there know why that's a rule and what the downsides of mitering angle iron are?

I would just use a G clamp and a 9 inch angle grinder. Good page btw 👍🏻

Thx for those tips. Yous seems to have now a mod on your bandsaw to improve vertical use, you plan to make a video on it ? Thx

@5thStreetFab

6 жыл бұрын

Cedric Zgood I think I'll make a video on it pretty soon thanks

Thanks, I'm using an old bed frame to build a base for a stove in my airstream

@5thStreetFab

6 жыл бұрын

Dennis Alan City Boy Homesteader right on! Airstreams are sick! Good luck

Does all cutters got the Angle?Or do it by guess

Hi nice

Besides the table, have you done any other modifications to that bandsaw? I'm just a home gamer, and was thinking about picking one up. How's it working for you?

@5thStreetFab

6 жыл бұрын

i havent had any real problems with it. It takes some time to get it dialed so it cuts straight and it cuts slowly but other than that i like it a lot!

I got a question for you I just bought a welder I've been using flux core I want to use gas. I don't want to run out of gas right away What size cylinder should I get 40, 80 If so how long does each one last..

Good job as always,keep them coming. How about a short vid on the saw table on the saw, just show how you made it using a tape measure so people can record the measurements and explain your process, don't have to build a new one.

@5thStreetFab

6 жыл бұрын

Mike Netherlin I think I might have to show video on that!

hello sir how to do angle frame comedition

I should of watched this before I built my frame. What kind of paint do you use to finish them?

@5thStreetFab

5 жыл бұрын

just rattle can

@kelvinprivet5202

3 жыл бұрын

READ what it says on the bloody tin.

please give me an idea what to do with my scrap metal pieces..i manufacture steel windows.

6:43 The reason that 45 degree cut is longer than the 90 and the reason why they dont match up is because the 45 degree cut is the hypotenuse of a right triangle. The hypotenuse of a r triangle is always longest... thats why it is longer than the 90 degree cut. Or put differently its the reason a 90 degree cut wont equally match in length to a 45 degree cut... its not as long

Do you have a particular method for tacking and welding these coped frames so they don't potato chip when you weld them up?

@5thStreetFab

6 жыл бұрын

I always try to weld the outside corners first. Then weld out the others. I'll clamp them down if I can.

I have a band saw the same as yours what did you make the table for it??

@5thStreetFab

6 жыл бұрын

James White I made this table because the one that came with it was flimsy and the screws stripped out.

@jameswhite9237

6 жыл бұрын

5th Street Fab Shop thank you for replying to this have you some pics to show how you done it

@5thStreetFab

6 жыл бұрын

James White I have some pictures of it on my Instagram page.

Hello my dear friend

Does anyone have the prints for this project?

Where did you learn to weld?

@5thStreetFab

4 жыл бұрын

All over. Places making parts for yahama, honda, fox shocks. Place building race buggies, class 10 and class 1. Custom gp exhaust shop. And a offshore boat company that I'm still at

How set angel roof top solar panels angle in fabrication

The video doesn’t have any audio

Where’s the audio

How about attaching an external drive to your phone via USB? Or you could invest 15 bucks and buy a 64gb card. Cheers, and thanks for the tips!

@5thStreetFab

6 жыл бұрын

MickHornbak I Would But it's an s6 and they don't accept external memory or SD cards.

@michor10

6 жыл бұрын

5th Street Fab Shop you can adapt it. Here's how: www.google.de/amp/s/www.geek.com/android/the-best-ways-to-add-removable-storage-to-the-galaxy-s6-1619583/%3famp=1

@michor10

6 жыл бұрын

You can get an otg cable which is quite cheap. Just make sure that it's compatible. I use that with a full fledged ssd hard drive on my oneplus and it's great.

@5thStreetFab

6 жыл бұрын

MickHornbak I might have to try that. My phone won't let me use any cord to download pictures to a computer it's on the verge of breaking. But that cords super cheap thanks bud!

@michor10

6 жыл бұрын

5th Street Fab Shop you're welcome. Another alternative is to copy your videos over wifi, if you have access. I use an app called file commander for that. You just need to share a directory from your pc (I'd recommend some public directory where you don't keep any sensible stuff). It takes a little longer to copy though.

Sound is very low

Do you wear Yamaka?

@5thStreetFab

6 жыл бұрын

Moshe Galimidi haha no that's just my hair! My wife likes it slicked back.

I loved the 1 minute speech about making the videos shorter and with more useful content. Too bad it took you a full minute to say though.

ح

God

That was hard to watch

Excuse me sir but the sound isn't good enough

@5thStreetFab

5 жыл бұрын

sorry these older videos were filmed with my phone so theyre not the best quality

You sound just like a white Michael Jackson

@5thStreetFab

5 жыл бұрын

A he he!