You sir, are a brave man! It's great to see people working on the M156 in their homes, especially with these cars getting up there in age. Keep up the great work, and looking forward to seeing the rest of the series.

@SamAbraham

6 ай бұрын

Thanks! Ran into a few issues but getting those sorted as we go

I recently had to do this job on my C63 M156. Apparently, its happening more and more with age on these engines. So much respect for doing this. Myself and many others are terrified to work on these cars. Can't wait for more updates!!!

@OGYELLOW

4 ай бұрын

How much did this run you and any other while your in there items?

Good work 👌

good job 👍

I had to replace my leaking radiator on my C63 amg on Christmas Eve also. It was not an easy task but I was lucky to get it done. Good luck brother

@SamAbraham

6 ай бұрын

Thanks!

Eagerly awaiting part 2 of this series! I must have watched all of your M156 videos over the years. Question for you, why does the lower crankcase section on some M156s have 3 machined "vents" on some but not others? Is it a difference on the M156 between C63 and ML63 applications?

@SamAbraham

5 ай бұрын

So much to edit, and mistakes have been made along the way! Luckily nothing too serious, but lots of labor involved as you can imagine. The engine went back in the car successfully, but lets just say I had to take a head off soon after haha. I haven't noticed the vents on the crank case, are you referring to the upper and lower oil pans? The ML63/R63 (and CL63/S63/SL63 if I remember correctly) are all front sump, so they have the lower oil pan toward the front of the engine. E63/C63 are rear sump. So the components below the bedplate are in different locations.

Orielys and advanced auto parts have free tool rentals for AC recovery, that way you don't waste your refrigerant. Then pump it back into the system.

@SamAbraham

6 ай бұрын

Good to know for next time, not sure why I didn't think of that. Wonder if availability varies by state. Thanks!

My bed plate is leaking as well. I’m interested in doing this job too but I have concerns about it. To me it’s not as simple as just a re sea of the crankcase. You are removing the main bearings and re installing them can create oil pressure problems since they are seated from factory when torqued and change shape when tightened and loosened. How do you feel about this?

@SamAbraham

4 ай бұрын

Well, I've already done it and the main bearings were in decent condition. I probably would have replaced them if I were to do this again honestly, but after consulting a few AMG master tech friends, they said not to worry about it and just clean up the crank a little and go for it, which is what I did. I suspect that some day if I ever get myself a shop space and my dad no longer dailt drives this ML, I will probably replace them. For now though, no issues

подсказка. из 164 кузова проще тягать с коробкой, но без раздачи. она легко снимается на полу. а вот в 166 уже не прокатывает так)) электрическая рейка с задним поддоном портит все)) приходится ронять передний редуктор еще. но тогда с раздачей выходит. А так мотор то еще особо не течет. ко мне обычно приезжает уже просто кусок грязи с двум я дырками. для залива масла и слива 🤣

Do you know the part number for the intake vacuum connector? Mines is old and loose and im not trying to spend 4 grand just for something so minuscule

@SamAbraham

4 ай бұрын

Are you referring to one of the vacuum connections up front? Or at the back of the manifold

@ajtoofly7315

4 ай бұрын

@@SamAbraham in front of the manifold

Isosceles triangle works? 17:50

@SamAbraham

6 ай бұрын

Equilateral, 2 bolts at each point

How's it going man? Any update?

@SamAbraham

4 ай бұрын

Lots has happened haha, long story short, I made a mistake but nothing fatal. Haven't had time to work on the car as I've been back at school 150 miles away, but the engine has been back in the car for awhile, most parts I needed are already at my house ready to go

Omg not me, I’ll pay my master AMG tech with 40 years in the game to do anything like this regardless of cost.

@SamAbraham

6 ай бұрын

Nothing wrong with that! This is for people like me who enjoy a good project. Not always about cost, although i’m sure for many it is, especially as some of these M156 powered vehicles plummet in price.

Youre only 23??

@SamAbraham

6 ай бұрын

22 actually haha

@OGYELLOW

6 ай бұрын

@SamAbraham wild dude. You have alot of knowledge for your age. Hopefully the reseal is going well. Happy New Year