airman 👍

this is such a wonderful video and there are so few takers for it . thank u sir ji , lovely information sharing

Great 👍👍👍👍

very interesting for me as a non-pro that is interested in mechanical devices. thanks for sharing!

Very nice..!!!!!!!

Amazing

good job

Nice jobs

Thank you

Thank for you good job

@TEDDYKASHIMURA

4 жыл бұрын

thanks

Very good

very good work by experienced technician thanks

@TEDDYKASHIMURA

4 жыл бұрын

Sreejith Ts Thanks for watching and support

@gunterweber1972

2 жыл бұрын

Man sieht im ganzen Video jedoch nicht wo das Laeuferspiel (Spaltmass) eingestellt wird. Ohne das richtige Spiel wird sich der Verdichter bei Erwärmung ( Lastlauf) zerstören.

Starting from 1:42 I recommend to use bearing fitting tools for careful mounting eg. simatec ft33, unless you want to damage the bearing (the most common bearing issues are caused by improper mounting)

@TEDDYKASHIMURA

4 жыл бұрын

Michał Kraus thanks for sharing . I’m using the stick is full copper stick, not metal stick. I choose the Cooper because can protect the bearing surface when install . I know this is not the probability tools. Thanks for your reply I will improve the tools when doing the airend

@kerblow2017

4 жыл бұрын

What is the temperature settings you used in bearing?

Hi sir, wanna ask about how u dismantle the cylindrical roller bearing?

May I know where can I learn how to service and overhaul air compressor in Malaysia?

There is one hole fitted with alenkey bolt what is the uses of that hole please can you tel me sir?

bom trabalho obrigado por nos mostrar seu trabalho bem feito isso que vc jateia ai no parafusso como chama onde podemos comprar

@ronissonsilvestre9285

3 жыл бұрын

Bom dia. Acredito que seja lixa d'água.

porque o vídeo não esta na velocidade normal afinal amigo você queria mostrar o que ?

Hi. Any possibility I can learn how to overhaul an air end through your program?

@TEDDYKASHIMURA

4 жыл бұрын

Michael Jay Pernes I will try my best when I overhaul the AIREND and taking the video thanks for support

I can be considered in the 25μm to 50μm High Pressure discharge clearance, to 100μm to 150μm, low pressure suction clearance for AIRREND ELGI, please tell me about these clearance. I have a problem with a compressor because it was necessary to change the bearings because these don't work and the screws suffered many scratches. Please support if the clearances gives are a good option to improve the vibrations in our device.

@AntonioRamirez-eu9kx

8 ай бұрын

it must be 0.009 "

Why heating bearings and gears when assembling and at what temperature? what is the name of heating equipment? please pardon me for asking

@TEDDYKASHIMURA

3 жыл бұрын

when need to remove used old bearing must heat the metal . If you no heat the metal too difficult to remove. Puller special tools also can remove the gear and bearing , but will spoil the metal shaft surface. install a new bearing also need to heat the bearing , because you heat the bearing the bearing hole will increase the size. after install the bearing cooling down will going back the original size. Heat will increase the size . Cool will decrease the size. different size bearing different timing and tempeture.

good video. where can I find a manual about repairing airend??

@TEDDYKASHIMURA

4 жыл бұрын

Marbi25 what model AIREND you want to overhaul?

@ratneshk.compressiorborewe3947

3 жыл бұрын

Pls vedio normal.

@ratneshk.compressiorborewe3947

3 жыл бұрын

Atlas 1200-330 airend overhoul mannual provid me.

What is the machine you use for the bearings at 2:12? It heats up the bearing?

@TEDDYKASHIMURA

2 жыл бұрын

SKF Brand bearing heater

Sleeping now

You put too much high temp silicon gasket, I suggest to use loctite 518

@TEDDYKASHIMURA

2 жыл бұрын

Thanks For Comments. Now we Using Loctitle gum already red color ..

It's not a good reparation.. You sould use paper gasket with the according thickness to maintain the compresion chamber measure, if you use joint paste you are changing the total length and will be problems.. Take care

@TEDDYKASHIMURA

3 жыл бұрын

Mamame Laverga thanks your sharing🤝

Kalau overhoul kompresor denyo 390 bisa gak bos? Mesin saya posisi di Semarang. Thanks

@TEDDYKASHIMURA

4 жыл бұрын

You want overhaul AIREND or engine this Denyo 390

Elgi.450/150.repreng.bareng.number.dala

iyi calısma

Kalau ngatasi masalah temperatur tinggi/ oli gak mau naik bagaimana mas...

@Od13ok

4 жыл бұрын

Refan Afandi sniper merk apa bos? bs di bantu email od13ok@gmail.com 😅

@TEDDYKASHIMURA

4 жыл бұрын

When high compressor oil temperature have this few reason , maybe the radiator cooler dirty ? Fan belt condition not good ? Or Compressor oil thermostat problem etc ....

The first of NU* inner bearing too hight temperature.

@TEDDYKASHIMURA

6 жыл бұрын

Lu Van Com I follow Japan original bearing parts. Next time I try using another bearing... thanks for recommended

Bisu tidak ada petunjuk teknis pemasangan bearing

Comproser model 390s kalau untuk minyak apa yang perlu di isi di dalam gear itu

@TEDDYKASHIMURA

4 жыл бұрын

Shell Corena oil Rs32 Mobil Rarus 424 Faircol RA32

@TEDDYKASHIMURA

4 жыл бұрын

Total Fluidmatic IIIG Automatic Transmission Fluid

@rumahkuburmarimasuk7481

4 жыл бұрын

@@TEDDYKASHIMURA ads sample gambar bos

@TEDDYKASHIMURA

4 жыл бұрын

catalog.total.sg/en-sg/products/9t0/FLUIDMATIC-IIIG

@rumahkuburmarimasuk7481

4 жыл бұрын

@@TEDDYKASHIMURA untuk rotary gear...berapa liter perlu di isi?

USELESS ... kill that music and say something instead !!!!!!!!!!!!!!!!!