Air pump models, Cleaning and using Spaceman soft serve machines

Chapter Guide:
0:00​ - Draining Product
0:56​ - Disassembly
4:40​ - Washing
5:30​ - Assembly
7:49 - Air Pump Assembly
10:17​ - Sanitizing
11:00 - Adding Product and Priming
12:06​ - Freezing Product
This video will guide you through all necessary steps and how to clean your Spaceman air pump (pressurized) soft serve freezer. While the general principles in this video can be used for most pressurized soft serve machines, the video is specifically intended for the following C Line models:
Spaceman 6228A-C, 6234A-C, 6235A-C, 6236A-C, 6250A-C, 6378A-C

Пікірлер: 11

  • @terminosa.6061
    @terminosa.60614 ай бұрын

    Thanks a lot for the very instructive video. How often is the cleaning required in a resturant which is open 6 days a week with an average of 2 times 6 litre refil in each.

  • @spacemanusa

    @spacemanusa

    4 ай бұрын

    You're welcome, and thank you for watching! You should check with the local health department to see how often they require you to clean your soft serve machine, especially if you are using a product with dairy. For the air pump assembly, we recommend daily cleaning for optimum performance.

  • @terminosa.6061

    @terminosa.6061

    4 ай бұрын

    Thanks a lot for the quick reply.

  • @kraftpunktv
    @kraftpunktv Жыл бұрын

    Thank you for this video. The company I work for just started using your machine, a Spaceman 6378 a c, and this video does a great job explaining how to properly care for the machine. We have been learning how to use and run it so I was trying to troubleshoot an issue with the air pump seizing up. I believe this video helped me figure out the issue which was that one of our mixes when added to the hopper was still slightly frozen so it was chunky and therefore clogged the tube and the air pump. We disassembled and cleaned the air pump and tube but then could not get the air pump back on after doing so. The air pump would not align up correctly and I could not get it under that locking mechanism in the back. Are there any tips, tricks, advice, or other videos that may troubleshoot that issue? Thanks so much again!

  • @spacemanusa

    @spacemanusa

    Жыл бұрын

    So happy to hear the video was helpful! Frozen product can for sure clog up the air pump and cause issues. Regarding your question: Very rarely, the pump drive shaft (in the back of the hopper) will be rotated such that it does not align with the mating gear pump assembly. In this case, you can re-assemble the gears so they are rotated slightly different, or you can press the wash button briefly to rotate the pump drive shaft to a different position. Be careful to always ensure the machine is assembled with the discharge door installed prior to pressing any machine function.

  • @NishDabs
    @NishDabs3 ай бұрын

    Hi, I have a S60A, and the agitator doesn’t spin, is this normal? We also can no longer open side drip tray, any tips?

  • @spacemanusa

    @spacemanusa

    3 ай бұрын

    Hello! On Spaceman machines, the hopper agitator will only spin when the hopper is actively cooling (compressor is on). You may notice this happens after a delay, depending on the temperature and set temperate of the hopper.

  • @adrianasak
    @adrianasak3 жыл бұрын

    Do you have spare parts, technical assistance? I need an extracting front.

  • @spacemanusa

    @spacemanusa

    3 жыл бұрын

    Hi Adrian, thank you for watching our video! For parts you can purchase here: www.partstown.com/spaceman-usa/parts For technical support you can always contact service@spacemanusa.com

  • @differentworld5692
    @differentworld569223 күн бұрын

    Hi what is the *AMP error *

  • @spacemanusa

    @spacemanusa

    23 күн бұрын

    Hi! I’m not sure but you can reach success@spacemanusa.com for any support or questions you have. Be sure to include your serial number so they can pull the correct configuration!