Advanced Relay Tutorial: Turn Signal Integrated Brake or Parking Lights (Example 4)
www.hournineracecraft.com/relays.html
Pin Layout:
Pin 30 is connected to your power source, you should put a fuse on this connection (or you can connect this wire to your parking lights if you don't have too many bulbs).
Pin 85 is connected to the factory turn signal positive wire near the bulbs.
Pin 86 is the connection to ground.
(Note): Pins 85 and 86 can be swapped, they just power your coil.
Pin 87 is the connection to your new bulbs and this flashes on WITH your turn signals. When the relay is triggered then pin 87 will be connected directly to pin 30 inside the relay.
Pin 87a is the alternate flash, this pin will connect to pin 30 while the relay is in the OFF position. This light will be on while your parking light is on, until you turn on your turn signals. When your turn signal is on this bulb will flash OPPOSITE the turn signal.
The end result:
You will have extra parking lights that power on until you turn on your turn signals, once the turn signal is on the extra bulbs will flash opposite your turn signals. You will also be able to connect extra turn signals to another pin coming off of your relay, these will flash with your turn signals and will not change the blink rate.
Disassembled Bosch-style relay
• How to wire a relay, 5...
More relay videos:
5 pin vs 4 pin wiring: • Relay Tutorial: 5 pin ...
Dual Power Source Switching: • Relay Tutorial: Dual P...
Swapping a Positive for Ground: • Advanced Relay Tutoria...
Automate with Positive or Negative wire: • Relay Tutorial: Automa...
4 mode horn button: • Factory horn button wi...
Other interesting videos:
Sensor school ((coming soon))
Polishing Carbon Fiber • DIY, Polish Old Carbon...
3-Point Strut Brace Installation • 3-point strut tower ba...
GTFour Conversion • GTFour Celica body con...
Reset Toyota Maintenance Light • Resetting "Maintenance...
#leds #led #ledlights #offroadlights #foglights #rooflights #wiring #electrical #relay #relays #electricalwork #solder #soldering
Пікірлер: 49
Ahh thank you!!! The diagram is soooooo helpful!! Been looking for best info on KZread for few hours and finally found this! ❤️💆🏼♂️😎🙏🏼🙏🏼
Really really really helpful. Took me hours to look for someone to explain it correctly! Thank you!
This was Great, Thanks 👍
OK Thanks For The Info , But To Run Head Lights & Turn Signals , I'LL Need The 5 Pin Relay Right ?
Hi thanks for the information . l do appreciate it .
If on my car I was using a led tail light but was also used as a black light, what would I use to cut the power while the brakes are depressed to allow signal to flash ?
Hey mate, just a quick question.
If parking light is off, will the turn signal work or the parking has to on to work as turn signal.?
id love this on my double truck 26mt long 9 blinkers a side and people dont see them or read them cause theres other lights the same colour around it and i want the whole lot to blink like this.
Ive try this diagram for Left and Right rear brake light but my 30 & 85 feed to my turn signal and 87 my brake light. When the turn is on both my brake light is on...i only test one side only. should i wire both using 1 right relay and 1 left relay to make it work when turn left is on brake left on not both side
I'm trying to wire led tail lights on my motorcycle. I have Run/Turn/Brake plus ground for both sides on the bike and I'm trying to wire this into a two wire led light (so 4 into 2). Can you help with the construction of the circuit?
Awesome video dude! One question though, I want the side light to turn on the same time as the park light and flash the same time as the turn signal light, not flash the opposite way. Do I wire a 2nd 5pin that runs from the park light to the 30 of the 1st relay?
So I need a 5 prong relay to have opposite flashing of the lighta
This was a real help...I'm a volunteer FF and I am outfitting my personal truck with quarter sized LED's (Orange and Red) I am putting 5 of each, 10 total on each side of my running boards. I am gonna ask if you would know a way to ALTERNATELY flash the RED LED's then the ORANGE LED's (Wig Wag style) using a version of this technique?
thanks for the video, learned a lot. but if I wanted the same light to be my running light & turn signal I just 87 & 87a to the positive of same bulb? I would need 2 relays for a right ? thanks
i have a truck with tow mirrors that are signals i want to turn them to runners when not flashing... how can i do that without having a steady burn when my night time lights are on its a basic on and off led not a multi function
Will the turn signals still work when you have your lights off?
I would like this on my car but would like to use LED bulbs, how would it then be wired? Can you help?
I have tow mirrors that have a turn signal in the front of them. It is wired as a turn only. I want this one light to be a turn signal and a running light. When the turn is off I want it to be on as a park light. This can be done with 2 diodes and a resitor. Can it be done with one of these relays?
Somehow you' forgetting that a) you need a brake switch to energize brake light, whether or not you use a relay