This is the only Ambassador that I am familiar with. I had a 7000 very similar to this at one time. They are beautiful little machines! - Chris

@2ndChanceTackle

Жыл бұрын

Yes they are!

Good luck to you and I hope you get your voice back👍 Thanks for the great vids

@2ndChanceTackle

3 ай бұрын

Thanks 👍

I love all my Abu's....all 23 of them !

@2ndChanceTackle

Жыл бұрын

I like them as well. Hard to beat the older made in Sweden ones - Dennis

6500 and under. Still made in Sweden and one of the most dependable and easy to work on reels. And parts available like a lot of Penn reels.

@2ndChanceTackle

Жыл бұрын

Just be careful - there are several version made in China that are not up to the older standard

I just bought one today! so thank you for having this ready for one like myself! 😊

@2ndChanceTackle

Жыл бұрын

YW - Best wishes on tuning up your reel and on great fishing - Dennis

it took me a minute to see what you were talking about the rim of the spool, once I did, I wonder how it turned at all

A good ball of line for the heat gun😂

One of my favorite Reels .

@2ndChanceTackle

Жыл бұрын

Mine too!

I've got an old 5000 series from I'm guessing 1960's and as far as I know it's never been apart and was curious if servicing would be similar to this 6000?

@2ndChanceTackle

Жыл бұрын

Yes - the servicing is similar - You can use this video as a reference Dennis

Believe it or not, I actually had a reel come to my shop that had automotive grease in it. And old grease at that.

@2ndChanceTackle

Жыл бұрын

Easy to believe. Axle grease no doubt. Hate it! and the Lithium spray grease too! - Thanks

Hi I know this is a year old but my uncle just gave me his reel and I really want to teach myself how to service it. Your video is really great to follow. Can you tell me what oil, penetrating oil, and grease you use. This may sound dumb but I’m an absolute newby but are thoroughly enjoying the process! Also my reel has the opposite issue - it looks to have some dry and even rusted pieces. Can these be serviced or do they need replacing? Thanks for your videos.

@2ndChanceTackle

3 ай бұрын

I use any brand penetrating oil including the store brands. If you want a name brand, WD-40 is that. I use Penn precision reel oil and grease. You can find these in a combination pack online and buy through many resellers. Thanks for watching and for asking - Dennis

@bowlhead03

3 ай бұрын

@@2ndChanceTackle Thanks. Appreciated. Just in relation to the last question - if the reel is void of oil and some pieces almost rusty - can they be rejuvenated with the penetrating or or will I need to purchase new pieces?

Hey Dennis, I have a Newell 338 I just got off Ebay, its spool is very loose , how can I adjust the spool to where its tighter and how tight should it be for optimal casting?

@2ndChanceTackle

Жыл бұрын

The bearings on both sides have a screw driver slot. Turn the screws clockwise to tighten. Tighten it down all of the way and then back it off about 1/4 to 1/2 turn to set the right tension for casting - Dennis

I am in Australia.. I'm wondering when you filmed this service.?

@2ndChanceTackle

3 ай бұрын

I filmed this one about 1 year ago

Can I use dawn dish soap to do a clean on the reel and as far as cleaning the outside what would you recommend

@2ndChanceTackle

5 ай бұрын

I do not recommend dish detergent. It is formulated to dissolve grease and rinsing down your reel with it will dissolve the greases and oils in the reel. I recommend only a fresh water bath. To clean the exterior, you can use a rod and reel cleaner. Penn makes one that I use. Thanks for asking - Dennis

I didn't look closely but I didn't see the 2 brakes that this reel comes with, don't you use them??? Greetings from Uruguay

@2ndChanceTackle

8 ай бұрын

They can be removed or sometimes they fall out. I use the brakes in mine. This owner did not - Dennis

I have one with the level wind. Can the level wind be removed to make a good casting reel?

@2ndChanceTackle

2 ай бұрын

You can, but it should be a good casting reel without doing that. If you want to remove the gears to improve casting. Make sure you remove the line guide and pawl as well as the plastic idler gear in the non gear side plate. Once you remove the line guide, pawl and cap, put the worm gear and shield back on the rel. That will prevent water intrusion. Keep the idler gear and other parts incase you want to restore the line guide function in the future. Those parts are expensive, so you can avoid future costs if you hold on to those parts - Dennis

Are these worth anything? I was given a 3 screw red 6000 or should I just go fish with it and is it good for normal Midwest bass catfish ect fishing ?

@2ndChanceTackle

4 ай бұрын

Take it fishing! They are worth about $50 and there are plenty available, not rare

The handle moves in and out bout 1/8" on my brand new ABU Rocket...any idea ? Help please

@2ndChanceTackle

Жыл бұрын

First guess is the the "E" clip is missing from the gear shaft. That holds the sleeve on and the movement could happen if it is missing - Dennis

About how much would it cost to service that same reel

@2ndChanceTackle

Жыл бұрын

About $30-35 with shipping

Have an old silver shield version. With mine I’m having extreme issues with servicing. Taken it apart 6 times now and I still get issues with reeling in. There is no line and it is well oiled, it feels like it has a fish on or the drag is high or something.

@2ndChanceTackle

Жыл бұрын

Have you replaced the drag washer? Do you have all of the shine washers in the stack? You may be bottoming out on the gear sleeve if the washer is worn or broken - Dennis