No video
99-07 Chevy/GMC Truck Steering Gear Box Installation
2001 LB7 Duramax | GMC Sierra 3500 Crew Cab Long Bed Dually. Seals blowing out on the OEM steering gear box is a fact of life, especially for trucks that are or near 20 years old. Luckily you can pick up a re-manufactured replacement machined to have tighter tolerances thus making them last longer. As an added bonus they are pretty cheap to replace and do not take a whole lot of time or special tools.
Pick yours up:
🔴Cardone 27-7589 Remanufactured Power Steering Gear: amzn.to/3xboa1i
Puller Kit:
🔴YSTOOL Front End Service Tool Set with Automotive Ball Joint Separator Tie Rod End Puller Pitman Arm Remover 5 PCS Removal Splitter Kit: amzn.to/3PVjDHH
Пікірлер: 87
I really appreciate this video. Most videos are done in a pristine shop with no issues. I appreciate someone doing it in their driveway, having a few hangups the same as I will. You didn't cuss as much as I will though.
@KooshdaakaaGarage
Жыл бұрын
Thank you for that man. I hear ya on that! This channel is 100% dedicated to the weekend warrior driveway mechanic with a wrench in one hand and a cold beverage in the other 🍻
@samho9318
Жыл бұрын
@KooshdaakaaGarage Thanks for taking your time to help others. I replaced the sterling wheel bushing but my truck still make some noise. May take a look at my sterling box. 2005 Chevy silverado 2500 HD 8.1 gas.
Mahalo🤙…You have been like amazingly very descriptive in ALL that you have done…That’s what I needed to see! 😊
@KooshdaakaaGarage
Жыл бұрын
Gunalcheesh (thank you) my friend! 🍻
Ooooh , I don't have 41 minutes right now, I'm hand drilling a well and cleaning up carbuoys for "wine season" but I stopped by for a view & a 👍 Party on.
@KooshdaakaaGarage
2 жыл бұрын
Hell yeah Angus, you are living the dream! Thank you for stopping by 🤘🥳🙌
Yes the 5.3 does have it as well that's what I have in my avalanche. Witch thanks for the video as I've never changed one of these yet now I know what to do exactly as soon as I do it
@KooshdaakaaGarage
11 ай бұрын
Heck yeah, best of luck. You got this! 🍻
Had the pinion nut come off my truck. Before watching this video i recommend lok tight instead maybe a low level though.
For me it was hard.. harder then installing the front differential... lol
Nice video. I have a 2005 Sierra 1500 Z71 that is leaking too. I will be replacing mine as well sometime this spring. Probably will go ahead and do steering stabilizer at same time.
@KooshdaakaaGarage
Жыл бұрын
Thanks man! You're truck will feel brand new after replacing the gear box and stabilizer. I went with the Bilstein stabilizer and 10/10 would recommend. Very smooth turning, great recovery, and handles dirt roads like a champ 🍻
Buen video, me va ayudar mucho ahorita que tengo que cambiar esa pieza, no se porque no tienes tantos like si esta mucho mejor que muchos que eh visto, good job bro 😎 tienes un suscriptor más.
@KooshdaakaaGarage
Жыл бұрын
Hey thank you for that brotha! I appreciate it :) Best of luck!
Great Video! Have a great day Brother! Logging! Have done alot of that! Awesome Builds! Much appreciated 🏁 lmm in Colorado 🤠 Very informative 👍
@KooshdaakaaGarage
2 жыл бұрын
Thank you Ronald! You have a great day as well 😁🍻
Great video. Thank you!
@KooshdaakaaGarage
Жыл бұрын
Thank you!
Best video ever!! Thank you so much!!
@KooshdaakaaGarage
Жыл бұрын
Thanks for that man, it means alot! Best of luck with your install 😁🍻
Nice job man! How’s the steering box? Still tight? Thinking of Cardone but heard a few guys say it took 2 or 3 boxes before they had a tight one. Anyway, Great content man! Engine sounds smooth after all the love you gave her. Happy with everything you did? Anything you wish you did different?
@KooshdaakaaGarage
2 жыл бұрын
The box is still nice and stiff! I've been overlanding for a the past few weeks and she's holding together nice. The engine is running super smooth, way more power, bottom end grunt, and low egts. Even when I lug 5th gear and get upwards to 1094 degrees, she quickly comes down to 500 or so. I don't think I'd do anything different with Pig but there are definitely things I have lined up to do thatll add to the experience, help with cooling while up in the mountains. All and all she's running really good! I'll do a quick update video on my phone and post it for ya. Thanks man 🍻
I used the same puller and it broke it and bent the main screw bolt all up still didn’t get the arm off lol, idk if I should try a fork or what but this thing is stuck on here
@KooshdaakaaGarage
Жыл бұрын
Oh man that sounds like a royal pain. You might have to treat it like a ball joint and give it a little heat, give it some tension with a new puller, give it a few taps with a hammer, little more tension, little more heat, couple more wacks until it pops off. Kind of a pain given how tucked away the pitman arm is but that may be how you have to do it. Good luck!
I have an 04 Sierra, after replacing the gearbox with a Blue Top Gearbox and just about a whole front end Kryptonite rebuild my steering still feels way too loose to me. Ive been told by multiple mechanics that, that is just how these trucks are… Ive determined that the play is coming from where the steering column connects to the gearbox. Does this really not have a fix?? Its driving me nuts!
@KooshdaakaaGarage
5 ай бұрын
Ah man, yeah that's annoying. Your column is a two piece held together by a 15mm bolt I believe. Can you see or feel play in it? Seems like it could get stretched or loose if subject to lots of stress overtime. Another thing that helped tighten up my steering was installing the bilstein 5100 steering stabilizer. My gear box felt way too easy to turn when I first installed it and it honestly was a little scary to drive. The bilstein is significantly larger and provides more resistance than the oem version. Great for dirt roads and has smooth wheel recover after taking a corner.
Man I have to do this for my 05 Chevy avalanche it’s kinda intimidating
@KooshdaakaaGarage
Жыл бұрын
It was a bit intimidating for me too man. Once I got in there it wasn't too bad. If you use the same tools I used in the video then it'll make it much easier. Good luck man! 🍻
Thank you great job
@KooshdaakaaGarage
6 ай бұрын
Thank you!
Good job, thank you for sharing your video. Keep making good videos like that and I watch them I subscribe., Take care and be safe. God bless you.
@KooshdaakaaGarage
Жыл бұрын
Thank you!
Yeah well probably been leaking since factory installation
Good video. My question is. I bought a used gear box from a salvage yard. On the shaft of the gear box it has been turned all sorts of ways. How do i know where to position it? To put the steering linkage back on.
@KooshdaakaaGarage
Жыл бұрын
Thank you! This is how I centered the gearbox: install your steering shaft onto your new unit. Rotate all the way to the right. Next you are going to rotate all the way to the left. When you rotate to the left count the rotations it takes to get all the way over to the left. Now that you have your rotation count, divide that by 2. Whatever number that comes out to will be the number of rotation back to the right you will want to go. That will be your center. For mine I think the total rotations was right around 3 which put me at 1.5 rotations to the center. Now, when you remove your old gear box it is also important to straighten out your wheels so that the pitman arm lines up with your steering. Best of luck! 🍻
This vid be useful to be soon thanks buddy
@KooshdaakaaGarage
11 ай бұрын
Thank you for watching! 🍻
I recently had todo the gear box on my 1999 Chevy Silverado 5.3L following the idea from your video & first want to thank you . The video was great & easy to follow. I notice after my power steering feels really loose (no play just loose) then before .. I don't know if that's normal or if i did something wrong , any idea?
@KooshdaakaaGarage
Жыл бұрын
The samething happened to me and you know what it was?? My steering stabalizer was shot 😬 I couldn't tell before with the old gear box because the gear box was so shot it provided resistance where as the new gear box was much stronger with a tight tolerance. I swapped in the bilstein steering stabilizer and bam, problem solved. And to boot the bilstein steering stabilizer also added a faster turn recovery (wheel straightening after you make a turn). I made a install video of that too if you want to check it out. I talk about the very thing you just described 😁🍻 thank you for watching, I hope this helps!
Looks like a pain in the ass. Should I just keep adding fluid? I'm worried about the spline thing. Cardone has two version around the same price that look exactly the same, and they both say they'll fit my LLY. Wondering if the difference is the splines, and how do I know which one I have?
@KooshdaakaaGarage
Жыл бұрын
It is a bit of pain but 100% doable. Pretty sure you'll have a 3 spline. That seems to be the case most of the time.. the PSC have a 4 spline. You'll be fine to keep the fluid topped for a bit until the seal gets worse. I ran mine like that for a few years 😬
Thank you amigo thank you thank you.much
@KooshdaakaaGarage
Жыл бұрын
No problemo 🤘😁🍻
Great video. Does taking off the pitman arm mess with the alignment or steering wheel center?
@KooshdaakaaGarage
Жыл бұрын
Thank you akclan! are you in Southeast? Just curious, I bounce between JNU & POW. Anywho, though there is potential the alignment may be off depending on the difference between make and model of your gearbox and whether or not it was made on a Tuesday or Friday, in theory it should not make much if any difference at all. So long as you find the steering center using the method I show in this video then your steering wheel should be as center as it can get providing your tie rod alignment is also good. All of that said, if your alignment is already straight as an arrow, and you follow the techniques I show in this video then your steering should either be the same or better than it was when you started. Hope this helps, and best of luck! 🍻
Thank you for the information, Great job! I have a question I bought a remanufactured gear box how do I install correctly? Thank you in advanced!
@KooshdaakaaGarage
10 ай бұрын
This video is a step by step video on how to do exactly that 😁
@karlahernandez-dr6uq
10 ай бұрын
My thing is it is a remanufactured one do you think it is already centered, since yours is new mine isn’t?
@KooshdaakaaGarage
10 ай бұрын
@karlahernandez-dr6uq ohh gotcha gotcha. mine was a reman as well. It will install exactly the same as a new one though. In the video I show you how to center it. Essentially you spin it all the way to the right, then count how many turns it takes to get all the way back to the left. Take that number and divide it by 2. Whatever that equals out to is how many turns back to the right will be center easy peasy. You got this! 🍻
@karlahernandez-dr6uq
10 ай бұрын
@@KooshdaakaaGarage Thank you so much! I hope I get it done right!
fantastic job.
@KooshdaakaaGarage
Жыл бұрын
Thank you Stephen 🍻
Pro job
why didn’t u choose to just replace the seals, instead of buying a whole new unit? i’m considering the seal kit for my leaker…
@KooshdaakaaGarage
Жыл бұрын
Good question! I needed the truck back on the road asap for a 2 month overland trip I was doing and the Cardone boasted tighter machine tolerances over stock. That said I kept the old gear box and bought seals so I'll try my hand at that too 🤘😊🍻
Ha haa , 2 views and 2 👍. I just got the Vevo diesel 8 kw heater with the 12 litter fuel tank for the Appocolypse Bus , what a beautiful thing All aluminum and the size of a loaf of bread and under 200$ it is rock solid ! 👌
@KooshdaakaaGarage
2 жыл бұрын
I got 2 bars somewhere up a coffman cove mountain here on pow. Thought I'd say! Those 8kw heaters are freakin fantastic man, one of the best purchases I've made!
@angusmcnaughton4570
2 жыл бұрын
@@KooshdaakaaGarage I want to move to either Coffman or Thorne bay... or both 🤔, have the property all picked out, my place was up for sale for the last month, but no realtor so not much coverage. Lots of wierd shit going on in the world right now so I am putting it off for a while, but I never give up... timing is everything... inch is a mile. I am jealous you are at my dream spot ...YOU are living the dream. But this mountain is not too bad. I wish I was walking down the dock with the white Husky and hopping on a boat ... so much
@KooshdaakaaGarage
2 жыл бұрын
@@angusmcnaughton4570 you are absolutely 💯 correct there man, timing is everything 🤘 might as well take your time and do it right so you can get as much out of it as you can. I'm recording all the coffman and thorne driving I'm doing so I'll share with ya when I get back to home base 🍻
@angusmcnaughton4570
2 жыл бұрын
@@KooshdaakaaGarage it's Angus misusing tools and forums here , networking on utube. I am curious about how supplies, dry goods ? Groceries? And other shipped items are doing??? Both mainland AK. And POW . I have been keeping track of this for ever but it is looking really crazy globaly and definitely on the island of 48 states .I am not worried, I have everything from rice and beans to whiskey. Just curious. If I showed up on rainy day island I would have everything I need with me. That is part of my issue... logistics I would have a couple of shipping containers and likely driving a bus and box truck. Any information is appreciated, when I land there will be beer on tap , smooth ass whiskey the likes unseen, fireworks cannon fire and other disturbances. I am having issues on what I would leave behind and would be looking for an extra vehicle for the island. If any of this bothers you tell me to shut the F*ck up , I have already bothered a couple other people who probably think I'm a psycho... (and they might not be wrong) Thanks man , Angusinabottle@gmail.com This message will self 🔥destruct🔥 as soon as you get that email
On my duramax the steering wheel moves side to side its all loose would changing the box help
@KooshdaakaaGarage
Жыл бұрын
Hello Rivera and thank you for your question. If you have significant play in your steering wheel then it can definitely be your steering gear box going out. It might not hurt to change your steering stabilizer as well 🍻
So I just replaced my power steering pump and I’m pretty sure I’ve worked all the air out the system but not totally sure because I have this issue where my steering wheel only has power steering turning right, as soon as you turn left it’s as hard as a rock and when you touch the brake pedal turning left it kinda jolts the wheel the opposite direction any advice?
@KooshdaakaaGarage
Жыл бұрын
Hey Pat, sorry to hear about the power steering issue. Do you have any kinked or clogged hoses? I've seen this happen with a hose that was kinked during installation.
@patfansler8739
Жыл бұрын
No clogged hoses, came to the conclusion it’s this steering box, but I can’t get the damn pitman arm off
I just replaced my gearbox 99' suburban Chevy, but how long does it actually take to bleed air out? I also was driving down my street and the steering didn't want to turn.
@KooshdaakaaGarage
Жыл бұрын
It doesn't take long to bleed the air out. Few minutes at best.
Did you have to center the input shaft before install or was it factory preset
@KooshdaakaaGarage
Жыл бұрын
Hello and thank you for the question Kyle. I show you how to center the input shaft in the video 🤘😁🍻
Why didn't you flush it?
@KooshdaakaaGarage
9 ай бұрын
It's been leaking/flushing for several years by this point. I can assure you that the fluid is pretty new and had I not fixed the issue there would be new fluid it it again by the next week, the week after that, the week after that and so on :D
Wow, you still fumble with that skid plate?? I threw that trash away many years ago. I've gotta do the pump and gearbox on my 02' lb7
@KooshdaakaaGarage
2 жыл бұрын
Lol, these skid plates are trash. I'll make a nice new one before too long 🍻
@mariocorleone106
2 жыл бұрын
@@KooshdaakaaGarage i was thinking about fab'n one out of SS
@KooshdaakaaGarage
2 жыл бұрын
@@mariocorleone106 hell yeah, that would be perfect man
@mariocorleone106
2 жыл бұрын
@@KooshdaakaaGarage How's the Alaskan life?
@KooshdaakaaGarage
2 жыл бұрын
@@mariocorleone106 excellent! I'm quite a few miles back on logging road camping at the moment. Only spot in the last 100 miles I've had a couple bars of service! I'm video taping the ride alongs and will be publishing them this fall if you are interested 🤘😁🍻
Is it safe to purchase a used gearbox in your opinion?
@KooshdaakaaGarage
Жыл бұрын
As long as you've given it a good inspection I'd say so. You can also pick up a rebuild seal kit for about $20 and rebuild it before installing it. I have a kit I still need to install in my old gearbox so that I have an extra on deck or to give away or sell.
@joonajks
Жыл бұрын
@@KooshdaakaaGarage thank you 🙏🏿 I just subscribed to your channel!
@KooshdaakaaGarage
Жыл бұрын
@@joonajks Thank you!
@joonajks
Жыл бұрын
@@KooshdaakaaGarage yes, sir, you’re welcome!
Goodness. We don't need to see all the struggling and breathing into the microphone. lol! Just edit it to show each step.
@KooshdaakaaGarage
Жыл бұрын
Dang. I went to your channel to watch your videos to see if I could pick up some editing technique tips... but it appears you do not create content. Pity 🤷
How do you found center