88-00 Honda Sloppy Shifter FIX Step By Step
Автокөліктер мен көлік құралдары
The is the proper complete way to fix a Honda or Acura sloppy shifter this will not correct transmission internal issues but will help prevent premature wear on the system.
The common parts that wear out are below the links help the channel and cost you ZERO.
Change Lever Dust Seal A:
amzn.to/3Ya7GAY
Change Lever Ball Seat:
amzn.to/3majeXn
Stabilizer Bushing Kit
amzn.to/3y3ygkA
#efcivic
#crx
#civic
#acura
#honda
#sloppyshifter
#savetheefs
#classichonda
Пікірлер: 30
I just had this done on my 1990 crx si today
I was looking everywhere for the size of the bolt, thank you very much sir
@DIYKAI
2 ай бұрын
to replace the pin?
The shifter arm that you say there's not much to rebuild on is the part that causes the most play. When that 2 way universal joint at the end gets just a bit of play in it you have amplified slop in the gear stick. you drill out the rivets, replace the bushes inside (whether it be nylon or brass you can buy em online) and then use bolts to get it back together.
@DIYKAI
Жыл бұрын
Yes that’s another way to go Lucky these ones were ok…..thought about fabricating a u joint or something
@gasnation6968
10 ай бұрын
do you happen to know where i can find that bushingB
@DkpProductions
10 ай бұрын
My linkage is incredibly bad, I have a video of it. Looks like I'm out of gear lol
@DIYKAI
10 ай бұрын
Is in on the tube?
@DIYKAI
9 ай бұрын
they are not sold anymore you would have to make some or something
LHT performance used a ball peen hammer to lightly hammer the riveted area to tighten up a little of the free play. It isn’t supposed to be floppy, but not supposed to be super stiff.
@oregonfelder1
Жыл бұрын
kzread.info/dash/bejne/Ynx2tKuJkd3Pm8Y.html start at 2:05.
@DIYKAI
Жыл бұрын
Yes we seen Johns video he does great work ours was not bad maybe a thousand or 2 of play the bushing is what was worn in ours
Thank man ! I keep putting my boot on the wrong way I suffered a serious money shift because of it 🤦🏽♂️ Whole linkage fell out the bottom hanging on my exhaust, Do you know if the connection part with the pin and u joints goes up or down ? I noticed the connection is offset to one side not sure which way to install haha
@DIYKAI
Жыл бұрын
We will look at the diagram in the shop manual and reply back later today
@miclomusic805
Жыл бұрын
@@DIYKAI thanks I appreciate it big time 🙏 I tried to keep it all the same when removing but I just bought the car a few months ago not sure if the previous owner installed properly
I have a question about the grill lights where can I get the original lights for it
@DIYKAI
Жыл бұрын
What grill lights are you referring to
@Wes_off_road
Жыл бұрын
@@DIYKAI the original lights that are on the ram grill? I bought the ones you suggested for your grill but they didn’t work so I was asking do you know where I can buy the ones that come standard on the grill
@DIYKAI
Жыл бұрын
@@Wes_off_road ok got ya though you were commenting on this video. The original lights inside were cheap and we never found a replacement worth it….so we used flexible leds with sticky tape
@DIYKAI
Жыл бұрын
@@Wes_off_road when you say didn’t work what happened?
@Wes_off_road
Жыл бұрын
@@DIYKAI the lights I bought didn’t work because there not flexible