6 SOLDERING MISTAKES ON COPPER PIPE

Тәжірибелік нұсқаулар және стиль

6 SOLDERING MISTAKES ON COPPER PIPE
🚨 Livestreams|Behind the Scenes|Exclusive content plumberparts.locals.com/suppo...
----
🚀 LEARN PLUMBING ONLINE IN MY STRUCTURED COURSE (50% Before March): www.learnplumbingonline.com
🛠 AMAZON TOOL STORE: www.amazon.co.uk/shop/plumberp...
🥾 10% Off my workboots + workwear Use Plumberparts10: www.bigboots.co.uk/discount/p...
👓 10% Off Safestyle Sunglasses Use PLUMBER10: safestyle.com.au/?ref=PLUMBER10
Learn Plumbing Online is perfect for future apprentices, homeowners who want to understand and tackle more plumbing jobs in the home, handymen who keep turning down the odd plumbing job and more. With practical follow along video lessons and discussion board you can boost your knowledge in my amazing trade. Sign up now: wwwlearnplumbingonline.com
Don't make these 4 soldering mistakes that LOADS of people make when working on copper pipe!
TimeStamps:
00:00 Intro
00:18 Not making sure the copper pipe is clean
01:40 Not using flux on the copper pipe
02:50 Clean the inside of the fitting
03:38 AN EXTRA PLUMBING TIP
03:52 What too much heat does to your copper pipe solder
05:12 What too little heat does to your solder job
06:10 Useing the right amount of solder on the copper fitting
08:35 ANOTHER EXTRA PLUMBING TIP
09:10 Trying to solder when water is in the pipe
11:30 ONE FINAL PLUMBING TIP 😉
TWITTER🐤 / plumberparts 🔥
FACEBOOK👉 / plumberparts 🔥
INSTAGRAM📷 / plumberparts 🔥
SNAPCHAT👻 / plumberparts 🔥
-----
------
-------
PLUMBERS REGISTER HERE: www.plumberparts.co.uk/tell-me... ❤️

Пікірлер: 131

  • @plumberparts
    @plumberparts10 ай бұрын

    Hope you enjoy! Live on Locals tonight! 🚨 *_Livestreams|Behind the Scenes|Exclusive content_* plumberparts.locals.com/support/promo/PLUMB1M 🛠 *_AMAZON TOOL STORE:_* www.amazon.co.uk/shop/plumberparts 🥾 *_10% Off my workboots + workwear Use Plumberparts10:_* elwoodworkwear.co.uk/?ref=Plumberparts10 👓 *_10% Off Safestyle Sunglasses Use PLUMBER10:_* safestyle.com.au/?ref=PLUMBER10

  • @Maltloaflegrande
    @Maltloaflegrande4 ай бұрын

    They say a bad workman blames his tools. I used to believe this until I attempted a batch of soldering on my central heating. I did all the things in this vid by the book and it still leaked: that's THREE attempts all going wrong and boy was I tearing my hair out(I still had some in those days). Then my wife said "maybe it's your torch?" "No it can't be, I've had this for years and it's never let me down!" But after the fourth failure, I was desperate enough to pop round to B&Q and treat myself to a new torch. Instant success. The moral of this is that sometimes it actually isn't your fault. Check your gear.

  • @Andrew85or
    @Andrew85or3 ай бұрын

    Make sure you check what's behind the fitting your heating. If there's something flammable or heat sensitive,you could buy a heat shield or cut one of those foil baking trays in half and it'll work just fine. You may be able to layer aluminum foil but haven't tried that.

  • @pumpkinhead456
    @pumpkinhead45610 ай бұрын

    I've just upgraded some 22 to 28, with even a couple of 35mm tees. First time soldering larger pipes, was nervous but got there in the end. Plenty bird poop, snots, 2 leaks - got there in the end! Doing it again I'd flux 1 joint at a time in stead of a few, but otherwise quite happy for a pen pushing DIYer 😊 I learn all my stuff here, thanks for helping us! Oh PS, for very dirty pipes, a bit flux before cleaning will bring it up nicely!

  • @nicodavies1437
    @nicodavies143710 ай бұрын

    Number 1 rule to having solid clean solders is having flame control and understanding the flame. For example, soldering 15mm you only need a light soft flame which will slowly draw your solder in rather than having a massive out of control flame which will melt the fitting and flux and you'll end up with solder all over your fitting.

  • @andrewwilliams8454

    @andrewwilliams8454

    Ай бұрын

    Thats exactly what he said in the video

  • @anthonyhall854
    @anthonyhall8548 ай бұрын

    I used bread for years when soldering pipes with water in and always worked a treat , until on a job one day and the only bread on site was called Warburtons best of both! god knows what was in it, the joint soldered great but even after 2 days with the heating running the bread did not break up! had to pull the thing apart and the bread had turned to a sloid plug! just imagine what it does in your gut!

  • @Pseudify

    @Pseudify

    4 ай бұрын

    You have enzymes in your gut, but probably not in your water pipes.

  • @landsea7332

    @landsea7332

    3 ай бұрын

    Use white glue bread ... not whole grains .

  • @marciaedwardscrown

    @marciaedwardscrown

    Ай бұрын

    Hovis or mother's pride then?

  • @dimitar4y
    @dimitar4y10 ай бұрын

    remember to make mistakes and LEARN FROM THEM! Nobody ever did something the first time perfect :)

  • @YeahNoTellTheTruth

    @YeahNoTellTheTruth

    10 ай бұрын

    Sure, if you're going to correct yourself after and as he just said don't make these mistakes as they'll cause damage to yours and peoples property which he's right so your feel good positive vibe comment is contradictory to doing a good job on things like this.

  • @dimitar4y

    @dimitar4y

    10 ай бұрын

    @@YeahNoTellTheTruth i mean if you're gonna make a mistake on purpose you sure as hell ain't gonna do it in someone else's house. nothing contradictory. Also, nobody has ever discovered anything just by being born for it. Even the inventors got it wrong the first few (thousand) times.

  • @fredfox1764

    @fredfox1764

    10 ай бұрын

    no as i always say wilbur and orville wright didnt build a 747 first time off

  • @ImranAli-rp4kd

    @ImranAli-rp4kd

    9 ай бұрын

    Most things you’ll never get right first time but there’s some things you can get right first time perfectly

  • @blitheringrando1410
    @blitheringrando141025 күн бұрын

    Thank you, this video was invaluable. I was able to replace a leaky delta 600 series valve. We cut the old valve off at the body, sweated the little pieces off the pipe and trimmed the pipe to fit the wider valve body. We did it in 1 try thankfully. That brass takes a lot more time to heat up than that copper pipe does, we had to use a license plate heat shield when working in the wall.

  • @1-2_Flush_Water_Saver
    @1-2_Flush_Water_Saver9 ай бұрын

    Being a very experienced and master plumber myself, I never, ever use MAPP gas to solder. I only use it to loosen fittings that other barbarian Plumbers overtightened fittings with! It has oxygen in it to help make the heat / flame quite a bit hotter than just propane and the oxygen also gets into the solder and the copper which is not a good thing. Edward H. - “Integrity, plumbing, septic and drain“ out of the Clinton, CT USA area.

  • @sunkat76

    @sunkat76

    7 ай бұрын

    Thank you. this is good to know. So, what should I use? I am a newbie to this. Buying new kitchen taps: Want to solder in copper tails to copperpipe under kitchen sink. TIA

  • @bobbing4snapples

    @bobbing4snapples

    4 ай бұрын

    Dude, you are so full of s**t. MAPP is methylacetylene-propadiene propane, hence the name. It also hasn't been available in North America for years. There's certainly no "oxygen in it". Sounds like you're "very experienced" in blowing smoke up people's asses😂

  • @akc045

    @akc045

    Ай бұрын

    ​@@sunkat76 Propane torch.

  • @sunkat76

    @sunkat76

    Ай бұрын

    @@akc045 thank you!

  • @hlambourne3847
    @hlambourne384710 ай бұрын

    Make sure there's no fragments of wire wool in the joint

  • @kevinrayner5812
    @kevinrayner58129 ай бұрын

    I always have a problem with lead free solder. That goes for electrical soldering as well. I understand if it is on central heating you are still allowed use lead tin solder but not on drinking water pipes.

  • @Coein-King
    @Coein-King10 ай бұрын

    Love the video !!! But what about the wet rag and leaving the other end open ? I always got taught if you are soldering an elbow to flux both sides and be ready to solder both pipes going into the fitting rather then leaving none side open.

  • @niconine268
    @niconine2686 ай бұрын

    Very decent plumbing work

  • @videogalore
    @videogalore9 ай бұрын

    I'll have to try the Brasso trick, thank you!

  • @armandocontreras8114
    @armandocontreras81143 ай бұрын

    Thanks for your time

  • @rajan246
    @rajan2469 ай бұрын

    Bread for the heat bag - check. Loving it.

  • @shaneslattery2512
    @shaneslattery25124 ай бұрын

    Mistake 7 you thought that you were friends😂 great video thank you learning so much

  • @lannabulls
    @lannabulls7 ай бұрын

    Great video thanks. Which kind of solder do you use for copper to copper pipe? tin- lead or free leed solder used in electronics could be used? Thanks 🙏 so much!

  • @kendalnichols3843
    @kendalnichols38437 ай бұрын

    Lesson 2 could be to debur the pipe.

  • @cameronmurie
    @cameronmurie3 ай бұрын

    Good tips I enjoyed it. I am watching these as I have to do a pretty, decoration copper install for an airline. (3/4) I would like to see a demo about getting it right when you are up a ladder, hard against the ceiling and have to turn it into a T piece but you are 18 inches from the corner where you turn 90. Using brass wall Battens in brick. And after you are done the client is using a microscope to look at your joins.

  • @richardstewart6900
    @richardstewart690010 ай бұрын

    Had to learn soldering and compression joints on 15mm copper when we came home one day to find bursts in the washer & hose feeds in the garage. It was around 40 years back so no internet to fall back on. And yes, mistakes were made! Probably the very first joint I tried to do, I was stood there with the blowtorch for AGES, wondering why the darned thing wasn't working, why the joint hadn't sealed. Not knowing, I'd turned the torch on high and the solder must have drained out within the first few seconds. Got the hang of it after that but, frankly, would use plastic for 95% of the stuff I'm likely to do nowadays.

  • @paulverney6748
    @paulverney674810 ай бұрын

    Do you recommend having saw dust and used paper towel in the area behind the soldering flame? 😂😂😂 are you sponsered by local fire brigade! Love to see one on connecting chrome pipe to copper for towel rads.

  • @Micahberger1
    @Micahberger14 ай бұрын

    Great video!

  • @electrolatif
    @electrolatif10 ай бұрын

    Great video 👌

  • @juanzelaya2647
    @juanzelaya26475 ай бұрын

    Good class thanks

  • @mrpat2563
    @mrpat25639 ай бұрын

    Great video, Im not an plumber but after cleaning the copper you shouldn't really touch the area as natural grease from your fingers will contaminate the copper but these new acid fluxes are pretty good these days. Water boils at around 100C and for solder to melt it needs a few hundred degrees so if theres any water or steam you cant clear you will stuggle like hell! Ive used a vax vacuum cleaner in the past but if that fails a Compression joint or if you trust push fit is the other option. Thanks for your great videos.

  • @cleomcn
    @cleomcn3 ай бұрын

    Great video

  • @mikebryan544
    @mikebryan5445 ай бұрын

    Funny as mate nice one, good laugh on the job

  • @philgriffiths5514
    @philgriffiths551410 ай бұрын

    Brasso....Of course, I thought that's where you got the inspiration for your KZread image from. Good stuff. After watching that I feel Im a pro already.)))

  • @shooterqqqq
    @shooterqqqq2 ай бұрын

    I couldn't solder a pipe because I neglected to loosen the fitting from the water heater. There was a small water leak at the shut off and air was pushing into the pipe and creating a small channel for the leak.

  • @carltonbreezy
    @carltonbreezy10 ай бұрын

    We are not at home to Mr Cockup. One of my favourite things to say from the greatest British comedy series bar Rising Damp. Respect man👍

  • @leoanthony79

    @leoanthony79

    7 ай бұрын

    I thought it was Blackadder tbh?

  • @turboslag
    @turboslag9 ай бұрын

    What about vertical runs?

  • @ImranAli-rp4kd
    @ImranAli-rp4kd9 ай бұрын

    Some videos say put flux in the fitting and this one says don’t, so which one is correct ?

  • @jaffplumbs26
    @jaffplumbs2610 ай бұрын

    Legend 👍

  • @birdszed
    @birdszed10 ай бұрын

    Copper vs pen or p;attic pipes and solder vs speed fittings?

  • @rapstar4575
    @rapstar45753 ай бұрын

    Wowza ❤

  • @richardlewis5316
    @richardlewis531610 ай бұрын

    On many jobs I see the big lumps of solder at the bottom of the fitting where the previous plumber has used too much solder. After every joint I do I wipe the joint with wire wool as its there anyway from cleaning the pipe. This removes any excess solder and leaves the joint smooth .

  • @irishmike4914

    @irishmike4914

    5 ай бұрын

    If you are doing 50 joints or so you don't always remember to wipe everyone. As long as it doesn't effect the integrity of the joint no worries. The bigger issue is to go back and clean all the flux off so you don't have green pipes. I use a couple of spoonfuls of baking soda with water and wipe all the copper down not just joints. Way the grumpy old guys taught me!

  • @MrChrissy1r
    @MrChrissy1r5 ай бұрын

    To be kinder to my delicate skin :-) I use a scotch brite to clean the pipe and fitting, I also prefer use Everflux, but never get it on your skin.

  • @Wiltshire-observer
    @Wiltshire-observer10 ай бұрын

    There is a quick cheat for soldered fittings, using electrical solder with the flux already in it. Although more expensive, I use it with cleaning flux and it works on all copper fittings. The cleaning flux is now not so easy to get hold of, a bit toxic I think. If you want to master the end feed fitting, the ones with no solder ring in them, try electrical solder with everything cleaned up beforehand and a bit of flux if you are a novice. Works really well.

  • @videogalore

    @videogalore

    9 ай бұрын

    Interesting, although I don't know that electrical solder is suitable for potable (drinking) water though?

  • @SeanBZA

    @SeanBZA

    5 ай бұрын

    @@videogalore Modern stuff is lead free, just tin and a little bit of other stuff in it, so it is actually water safe. The old solder before ROHS is tin lead alloy, 60% lead and 40% tin roughly, depending on brand. But if you are doing refrigeration pipe MAPP gas is the thing, and you are actually melting the copper slightly, and the gas is cleaning the oxide off the surface before the silphos rod is used to weld the parts together. Have used it a bit on water pipes, and with this you do not even need fittings if you have the AC tools, as that allows you to make the one side expand ( for water pipe that is hard drawn first heat it to make it soft annealed copper again) to make a fitting that is way more than capable of handling water mains pressures. Worst though is when you find old imperial size copper pipe still in use, and want to mate to modern fittings, which will not work, so MAPP gas and weld the new tail onto the old pipe it is. That is in old buildings, with pipe in the walls, and you need to fit a new tap there, and not remove 20m of plaster to do it.

  • @videogalore

    @videogalore

    5 ай бұрын

    Thank for that @@SeanBZA, you've also answered why MAPP gas is hotter, I've often wondered that too!

  • @tookitogo

    @tookitogo

    3 ай бұрын

    @@SeanBZALeaded electronics solder is 63/37 (true eutectic) or 60/40, which is close enough and was slightly cheaper back when leaded was king. The first number is the tin, so 60/40 is 60% tin and 40% lead.

  • @paul_my_plumbs_uk
    @paul_my_plumbs_uk10 ай бұрын

    Wire wool is no longer recommended to clean the pipe prior to soldering use Abrasive strip or a pipe cleaner as wire wool strands can break off and get in the pipe 🤔🤔 that's how i was taught Sir James of Cambridge and i ❤️ the after clean with 0000 ultra fine steel wool as shown by PB

  • @happyn7817
    @happyn78175 ай бұрын

    You can use laco flux to clean pipes too

  • @mikhambilton1274
    @mikhambilton12749 ай бұрын

    Why don't U use siver solder on fitting I did and it's amazing

  • @markellwood4132
    @markellwood413210 ай бұрын

    Billy no mates and his soldering. Hahahaha. After watching this I am buying a heat pump.

  • @sethburgin5994
    @sethburgin599410 ай бұрын

    You didn't deburr the pipe. My father taught us plumbing. He did lead casting, oakum and lead bell end fitting sewer piping, and all kinds of odd old work that no one does today. I have his old tools and all of the hands on experience. We call the blobs of extra solder on the bottom of a sweated joint, a "Turkey Nut" or "Turkey Nuts". We used Flitz, Brasso and some polish for stainless steel firearms. I just blow the pipes out with compressed air. Dad would stuff bread in the pipe. It clogs fine screens in faucets and holes in shower heads. Freezing the pipe required a CO2 fire extinguisher, or a can of refrigerant for a car and it is way too expensive now.

  • @johnspathonis1078
    @johnspathonis107810 ай бұрын

    Hi Does the UK still use soft solder. I thought most counties had moved to silver solder. In Australia this would be banned.

  • @leighgardner3757

    @leighgardner3757

    10 ай бұрын

    I’ve been in the industry for 36 years always used soft solder without any issues I lived in nz for 7 years and they used silver solder due to the earthquake risk on joints don’t need to worry about that in the uk

  • @liam6200
    @liam620010 ай бұрын

    What are your views on solder ring fittings? I'm a diy'er and been fitting new rads in my house, have used them in all the pipework as I was worried about getting the amount of solder correct if I used normal fittings.

  • @nakchAk

    @nakchAk

    10 ай бұрын

    Truthfully as a diyer also I'd say hit and miss, I've had as many fail or require topping up with solder, that on my current renovation project I've just end fed solder for all copper joints. If nothing else a bag of elbows and pipe offcuts give you ample practice to feel confident soldering, and if your using solder rings your 90% there already so the blow torch doesn't feel alien in your hands, and that 5mm rule of thumb tip in the vid will help you master the last 10%...

  • @robkiss5272

    @robkiss5272

    10 ай бұрын

    You shouldn’t have to top up Yorkshire fittings. Might have to clean the pipe a bit better and maybe use better flux. Regards

  • @nakchAk

    @nakchAk

    10 ай бұрын

    @@robkiss5272 interestingly same prep and flux yielded perfect end fed joints and variable solder ring joints. Quite likely it's my technique or a rubbish quality fitting

  • @robkiss5272

    @robkiss5272

    10 ай бұрын

    @@nakchAk hmm it would bet on the fittings then. I stopped using those quite early and went to end feed ones. No ring just a few joints, be generous with solder at the beginning…it will be a bit messy but at least no leaks and then less and less solder…you will get the feel then like Jimmy says a bit of Brasso and it will be pretty too. 😀 Never be beaten

  • @blitzsuccess2303
    @blitzsuccess230310 ай бұрын

    How do you know that no solder has went into the internals of the pipe and to avoid a solder blockage?

  • @DavidNelson42
    @DavidNelson426 ай бұрын

    1a de-burr the inside end of the pipe.

  • @TheTurfrex
    @TheTurfrex3 ай бұрын

    If its a 1/2" pipe than mark(bend) 1/2" of solder and so on.

  • @fredfox1764
    @fredfox176410 ай бұрын

    i like your style mate

  • @Wobbly-World
    @Wobbly-World8 ай бұрын

    If you want a compression fitting to never leak (Especially on hot water pipes, that will expand, when hot, and contract as they cool, this eventually causes a leak, as the olive becomes loose on the pipe!!’) solder the olive on the pipe!!’ This turns your joint into a cone joint, assemble with PTFE or jointing compound, and I guarantee, done right, it will never leak, no matter how many Hot/Cold cycles it goes through.!!!’ If working with gas a compression joint is verboten, but by soldering the olive, and making a cone joint, it becomes an approved fitting, and will not leak ever!!!’ Takes a little longer to do but on hot water pipes, and gas fittings, well worth the effort, and extra time!!!’ ຈل͜ຈ .

  • @joebob227
    @joebob2273 ай бұрын

    Thank you for making a nice easy list on these! I'm a home handyman and can do almost anything to code, but plumbing scares the living **** out of me for how bad it can go if not done right. Trying to build up my confidence to do a small job replacing a hot water heater and this definitely helps! :)

  • @josephmueller1545
    @josephmueller15455 ай бұрын

    #7: Not wearing eye protection

  • @mickyue9928

    @mickyue9928

    5 ай бұрын

    Not wearing eye protect soldering above head piping and use too much solder then it drop into …..

  • @Brown969
    @Brown96910 ай бұрын

    Fire: I destroy property Water: Hold my glass 😆

  • @neilgage427
    @neilgage42710 ай бұрын

    When can we expect to see bread on the plumberparts Amazon store?

  • @plumberparts

    @plumberparts

    10 ай бұрын

    Next week - it’s in the oven!

  • @ScottyDog345
    @ScottyDog34510 ай бұрын

    Laco cleans the pipe

  • @pencilme1n
    @pencilme1n9 ай бұрын

    Just use plastic if you're a DIYer. Soldered copper gives the neatest slimline appearance for plumbing on show.

  • @yourdadsvan6763
    @yourdadsvan676310 ай бұрын

    I still don’t understand understand using mapp gas on 15 mm copper. If your not careful you can overheat the pipe

  • @gordslater
    @gordslater4 ай бұрын

    I'm always scared to use emery cloth because my uncle Jimmy told me he caught a nasty case of Dick Emery when he was in the army.

  • @martynbuzzing3327
    @martynbuzzing332710 ай бұрын

    Who knew? I do now, thanks.

  • @jimmycreamer7905
    @jimmycreamer79054 ай бұрын

    Sandpaper,wire brush …….scratch the pipe solder fills in the scratches better bond.

  • @sunnybeachwalks4k2022
    @sunnybeachwalks4k202210 ай бұрын

    Throw the torch in the bin and get a pro press 😂 save money on your public liability insurance 👍

  • @paul_my_plumbs_uk

    @paul_my_plumbs_uk

    10 ай бұрын

    🤣🤣🤣❤️❤️❤️™️ Press don't stress

  • @ganishnutinishnu7370
    @ganishnutinishnu73707 ай бұрын

    You used the right amount of solder the first time. The solder does go all the way round in the pipe. Also when soldering you should not move the blow torch all around the pipe it is better and safer to hold it in one lositiion and not move it. The pipe is going to get incredibly hot so there is no need to move it around.

  • @UrbanPlumbers
    @UrbanPlumbers10 ай бұрын

    No.1 mistake is using map gas😅😅😅

  • @MegaPokergod
    @MegaPokergod10 ай бұрын

    Why are you touching the copper and fittings with your hands .Any moisture from your finger goes on the copper

  • @elihissett7585

    @elihissett7585

    10 ай бұрын

    I am reading the comments looking for this one.

  • @harpo187bling
    @harpo187bling10 ай бұрын

    Le adder noir

  • @johnhehir508
    @johnhehir5084 ай бұрын

    Soldering with bread ,did you know that people who travelled around rural Ireland ,fixing pots and pans use to use wet chewed bread to help solder joints ,that chewed bread became known as A tinkers curse 😂😂😂😂

  • @RosskillbaneC
    @RosskillbaneC9 ай бұрын

    Noooooo not the fluxuatooorrr 💩

  • @ikabod6908
    @ikabod690810 ай бұрын

    Emily said..... about your small tip...

  • @jonathancruz6156
    @jonathancruz61565 ай бұрын

    PROPRESS

  • @ianlawrence92
    @ianlawrence922 ай бұрын

    Well shouldn’t you have cleaned the inside of the fitting second then before fluxing hahaha

  • @brucewarren7528
    @brucewarren752810 ай бұрын

    7 mistakes? Not wearing Safety Specs when soldering. You did get flux in your eye once.

  • @domthorpe4372
    @domthorpe43723 ай бұрын

    I'm scared of my blowtorch.... mine blow up on me and set my arm on fire lol long story lol

  • @David-uh9cc
    @David-uh9cc2 ай бұрын

    Heat the joint, pull the flame away, touch some solder to the joint and it will start melting when it is hot enough... Then it's ready...Touch the flame back again as needed...if ya leave the flame on the joint when you put the solder on it, you're just melting the solder and that's what causes drips and buildup.. also blue canister propane is just fine for residential water lines.. don't actually need MAPP... it's over kill.. the time difference to heat copper between the two is not that substantial..plus ya gotta have a dedicated MAPP nozzle.. I'm about saving money, not buying thr newest, fanciest tools and equipment... Ya just gotta be smarter than the task at hand.. thanks though..

  • @andydawson5341
    @andydawson53413 ай бұрын

    Wire wool ??? That’s a bit 1980s… Red scotchbrite, it’s the Daddy.

  • @neilfoster814
    @neilfoster8144 ай бұрын

    What I do when soldering a joint is, immediately after the solder goes in, wipe the joint round with a wet or damp rag. This not only removes any drips of solder, but if there are any pinholes in the solder wiping it will fill those pinholes before the solder sets solid.

  • @Pseudify

    @Pseudify

    4 ай бұрын

    I’ve heard this is not advised because that will cool the solder down too quickly and could create micro fractures, sort of like a windshield breaking in the winter.

  • @patriciacutts774
    @patriciacutts77410 ай бұрын

    Soldering pipes that are vatical can be a bit of a problem

  • @alklapaxida850
    @alklapaxida8505 ай бұрын

    i got me a blow torch cuase i want a blowie, , ,

  • @leesy78
    @leesy788 ай бұрын

    Soldering is art after 10 years 😂 clean jojns pipe and not to much flux i use solder long angle see others to close with there eyes near .not good

  • @rvalens2
    @rvalens29 ай бұрын

    You need to add a 7th mistake - not deburring the pipe.

  • @zitobin1
    @zitobin110 ай бұрын

    scotch brite?

  • @sween187
    @sween18710 ай бұрын

    Ok so this is a case of a little dab will do rather than the bigger the gob the better the job... Soldering.

  • @sween187

    @sween187

    10 ай бұрын

    For flux sake

  • @ajaywhite9103
    @ajaywhite910310 ай бұрын

    Cleans pipe then immediately touched it with his oily fingers

  • @lowe_the_showe202
    @lowe_the_showe2027 ай бұрын

    Never heard someone prenounce the "L" in solder. Lmfao.

  • @eckypooh50

    @eckypooh50

    4 ай бұрын

    The L is there for a reason... Except in America. Lol...

  • @lowe_the_showe202

    @lowe_the_showe202

    4 ай бұрын

    @eckypooh50 why is the K in knife?

  • @tookitogo

    @tookitogo

    3 ай бұрын

    @@eckypooh50Yes, the “L” is there for a reason: the artificial re-latinization of a word that didn’t actually have an L when it entered the English language. The original word was “souder” from French. The L was added centuries later, and the American pronunciation basically retained the original pronunciation, rather than the new “spelling pronunciation”.

  • @eckypooh50

    @eckypooh50

    3 ай бұрын

    Solder in french is soudre.. pronounced soo dray... Soder in american is sawder..​@@tookitogo

  • @tookitogo

    @tookitogo

    3 ай бұрын

    @@eckypooh50 You are mistaken. It’s _souder._ _Soudre_ is a different, unrelated verb. _Souder_ is, of course, the source word, and it evolved. But the point is that it didn’t have an L.

  • @David-uh9cc
    @David-uh9cc2 ай бұрын

    Abrazo is hug in Spanish, not brasso..

  • @plumberparts

    @plumberparts

    2 ай бұрын

    ¡Jajaja! ¡Gracias!

  • @David-uh9cc

    @David-uh9cc

    2 ай бұрын

    @@plumberparts fo sho... You're catching on! 🚿

  • @policematrixx
    @policematrixx2 ай бұрын

    buy a crimper

  • @landsea7332
    @landsea73323 ай бұрын

    I'd say if the soldering is not working then its probably - there is not enough heat , possibly because the water hasn't been drained from the system - OR the copper pipes have not been cleaned properly .

  • @chrisallen2005
    @chrisallen200510 ай бұрын

    ABRAZAR, your teacher is lying. Not brasso.

  • @J-G777
    @J-G7776 ай бұрын

    Goodness 😮😮 Talk 2 much... Just Stik to the point 👉

  • @jopiedebeer
    @jopiedebeer8 ай бұрын

    I'm sorry to say this, but this guy talks far too much. Please talk 1 and explain 10. Not the other way around.

  • @Raj-ul9my
    @Raj-ul9my10 ай бұрын

    These torches are dangerous and your not allowed to use them in domestic dwellings unless your liability insurance will cover you burning a house down and if u get a permit, its highly unlikely to both those answers but people still use them

  • @sailRichard
    @sailRichardАй бұрын

    A tip for rhe plumbing teacher - eliminate the music. It makes it harder to understand what you're saying. Otherwise, thanks.

  • @kevinrayner5812
    @kevinrayner58129 ай бұрын

    I always have a problem with lead free solder. That goes for electrical soldering as well. I understand if it is on central heating you are still allowed use lead tin solder but not on drinking water pipes.

Келесі