Yea man this is the best video on all of KZread about repairing rocker panels on this truck.

@slow_restoration

3 жыл бұрын

Wow, thanks!

@bobbyfinley6104

2 жыл бұрын

Agreed! I'm going to do my rockers on my ram and this is definitely by far the best video he doesn't leave anything out thanks for the video this helps tremendously

Everyone said... "Buy a 03 Ram 5.9 Cummins, it will last forever!" Engine, yes... rockers & bed wells not so much :'(

@slow_restoration

3 жыл бұрын

Unfortunately so!

@guydrusbik1347

11 ай бұрын

What type of welding equipment did you use

@slow6.7

10 ай бұрын

My trucks a Midwest truck it’s a 08but the salt took a toll on it, I’m getting new rockers, cab corners, sucks…

@slow6.7

10 ай бұрын

@@guydrusbik1347I’m gonna just tig it or mig it

@aaronhayden1780

Ай бұрын

My 03 cummins has 305,000 on it and still looks respectable, fuck off 😂

Great video. Those reading the comments, remove the negative cables from your batteries before you start welding and have a fire extinguisher near by just in case.

Man, I wish I had the money and or Knowledge to do this. I have a 07 mega cab that I would love to keep but it is a money pit. The rockers, cab corners and upper wheel wells are toast. Awesome work! If I decide to tackle this job, I will reference your video and pick your brain for months, I am sure.

@freakyflow

26 күн бұрын

Its actual cheap and easy if you do your homework on tools And how dos ..Your basic needs will be sawzall And grinder with a cut off wheel And a drill The welder which would best suit You And the cost And the need would be a mini mig welder - $200 avg Then get some 18 gauge metal to test it out on ..plenty of videos on how to weld thin metals ..Order your parts for that truck..Find the welds on the old parts Drill them out And chisel the rest Clean up the areas with the grinder And sandpaper Get some weld thru primer .. Before you weld make sure the battery is dis conn..And you have a bucket of water around ..Its good if you have a place to work on it And up to having min a compressor for airtools

I’m a so glad I came across this video! I starting to doubt my decisions I have made on my own 2006 2500. Your inside skirt panel is where I was struggling and you made a simple but a effective replacement for that. I could send you pics of my rockers and the trim cut’s are the same.Thanks for an outstanding video for this repair. P.S. I’ve also ran into dead ends on locating the inside skirt panel replacement.

Awesome work brother awesome. Thank you so much for showing how you do this. I have my 05 dodge cummins same truck. I have the same job to tackle. I rather buy the equipment to keep and have forever than pay someone 6k to do for me. Guess it's better to screw it up several times than pay another to do. Again thank you for sharing your knowledge. It doesn't really look that bad, just gotta dig in and get after it.

@slow_restoration

2 жыл бұрын

Thanks for the kind words! You got it, it's just work!

Currently working on my '08 Cummins shipping crate. Great video 👍

Looks like it spent its life in Erie, PA...rust belt of America!

Here is a guy that knows exactly what he is doing. And doing it the right way! Refreshing!!! Thanks!!!

@slow_restoration

2 жыл бұрын

Thanks for watching and the kind words!

You did a hell of a job.

This is a great tutorial. The beauty of doing my 03 is its already done most of the removal itself, haha. Thanks again

Those oval holes are where all the salt gets inside. Zbart used to be the way to prevent rust like that. If I lived up north, I'd be treating my NEW cars and trucks to prevent rot that like. Nice repair job!

Thats some real fine work you have done there ,very professional

That is an outstanding job great detail thanks for showing I’m doing mine soon did not realize there was A inner panel And I needed ideas how to build the backside that was great help

@slow_restoration

3 жыл бұрын

No problem 👍 Thanks for watching!

@Neverquit275

3 жыл бұрын

@@slow_restoration where are you located how does someone reach you

That is a proper repair job right there!

@slow_restoration

Жыл бұрын

Thanks!

You do fabulous work danny ☺️

@slow_restoration

3 жыл бұрын

Thank you 😁

ya did a hell of a good job ! best on a ram i have seen so far !!

@slow_restoration

3 жыл бұрын

Thanks, I appreciate it!

Nice job , you make it look easy,

@slow_restoration

3 жыл бұрын

Thanks 👍

Amazing job 👏👍

Awesome work man

I don’t care what anybody says about what you did it looks perfect to me and that’s exactly what I need to do Ty for sharing your video I have a 2010 ram 1500 and it looks similar to what you are doing hopefully not as bad but you just never know until you start doing it

@slow_restoration

Жыл бұрын

Thanks for the views!

Danny you do some impressive body work the way it should be done. Great job those rockers look good on that truck.

@slow_restoration

3 жыл бұрын

Thanks 👍

@304cumminsguy

10 ай бұрын

@@slow_restorationwhat gage steel did you use for the back side

@thomaspotthast3021

9 ай бұрын

I believe he said 14 gauge

Damn nice work I'm definitely keeping this video. I need to do the same on my 99 best video of how to I found. 🤙 thank you sir.

@slow_restoration

2 жыл бұрын

Thanks for the support!

Thanks for the video. Very informative.

@slow_restoration

10 ай бұрын

Glad you enjoyed it!

Like the video! I want to purchase the step plyers never seen those before. Nice work , new sub.

@slow_restoration

2 жыл бұрын

Awesome, thank you!

Great video. I'm about to do this to my truck.

@slow_restoration

3 жыл бұрын

Go for it!

@toddthompson3043

3 жыл бұрын

If you don't mind me asking where did the rocker panels come from. Im.having a hard time finding the kind you showed for.the outer rocker

Nice work

@slow_restoration

3 жыл бұрын

Thanks

I have ordered parts from Athens Dodge . They were new surplus OEM a new front differential was about $1100.00 delivered to my mechanic in NY . Body panels are also available .

Fantastic video!! Getting to see the breakdown on the layers was incredibly helpful and I learned a great deal! Thank you for this video.

@slow_restoration

Жыл бұрын

Glad you enjoyed it!

Fill it with fluid film until it starts draining from the drain holes after youre done welding to prevent the rust in the future also a friend told me energize the metal before doing anything to the metal it help deionize the metal so it kinda rejects rust then spray it with a neutral based ionized clear coat and proceed with the regular paint, and clear coats they said dodge used crappy metal that in conjunction with the positive charged paint they use causes rust faster than chevy or Ford thanks to du...ont paint company not saying any specific name 😁 because of legal reasons but the lead based elctron paint isnt good

great job

I’m in the midst of doing this too , finished the outter section , eliminated the center and had some custom bent for the inner👍

@SmokeyRam

3 жыл бұрын

I'm getting ready to order the metal for the job, why did you eliminate the middle piece?

@iansmith9201

2 жыл бұрын

i was wondering about this as well about eliminating the center, how did it hold up?

@willgarrick871

2 жыл бұрын

So far so good..

You make this look super easy I feel like it’s more time consuming then hard to do

@slow_restoration

3 жыл бұрын

Thanks, definitely time consuming! Just have to have some basic metal working knowledge.

@kylann4361

3 жыл бұрын

I did this to mine about 3 months ago. It was a ton of work but was totally worth it

@mikezaloudek4893

Жыл бұрын

I think the hard part is summoning up the motivation to get into it. Basic skills and taking your time to make it look nice is key.

Wow. This was an excellent video covering this repair. I honestly was shocked seeing the inner rocker panel just evaporated like that. It's amazing how bad that rust was. Great work on covering that. I know this video is old and I will subscribe and watch more, but just wondering what welder and what weld through primer you use? I kinda wonder seeing the inner panels with all the holes in them - do they have adequate drainage if salty water gets in there. I saw you addressed it with the replacement panels. I am looking at some 3rd gens and considering how much rust repair I want to get involved with. Saw one in Indiana that has some rust starting on the drivers side. Where there is rust there is more rust... Do you still have any access to get behind or inside those rockers and or corner with fluid film spray wands? I feel like annual application for any vehicle in the rust belt is a necessity to keep these trucks from rusting into the earth. I really like fluid film and supposedly there's a new one from PB Blaster I think.

Thank you Idk what I was gonna do for in the inner outter panel

Nice work, Hopefully it lasts another 10 years.

@slow_restoration

3 жыл бұрын

Hope so!

It's hard finding a good video on replacing rocker panels. This is a very good video. Its giving me more confidence to do the rockers on my Ford focus. Where do you find those step pliers? Thanks!!!!

@slow_restoration

3 жыл бұрын

Thanks, I've had these for years! I've seen them on Amazon, search flanging pliers.

I have done a lot of this sort of work on old GM square bodies and Gen 1 Dodges... I now have a really nice '06 Megacab diesel that is showing the signs of rust in the rocker panels. Repairing it looked a bit complicated at first glance. My question was if the doors had to be removed or not. It looks the doors would be a severe pain to remove what with a ron of wires feeding into them and all. but it looks like you did all that without removing them. Is that correct? I am going to watch this a few more times and get what I need together for the rebuild. Thanx so much for posting this!

Thank you for this!

So glad I have a West Coast 2004 Dodge ram 4x4 not a spot or rust anywhere

@slow_restoration

Жыл бұрын

Very rare out here! Most of these are really bad!

That very inner panel is called a floor sill panel.

@josephpuchel6497

2 жыл бұрын

Hello Jason is it available for my 2006 Dodge quadcab this floor sill panel ?? Thank you

@JasonTheMunicipalMechanic

2 жыл бұрын

@@josephpuchel6497 I doubt it. I’ve been looking for years for my 05 and it’s unavailable everywhere I’ve checked. The cabs are the same. It might be available if you have a single cab.

Good tutorial 👍

@slow_restoration

Жыл бұрын

Thank you 👍

Hey Excellent work. Excellent video tutorial Where you located My truck needs some sheet metal work.

Excellent work,I have the same issue on my 06 Hemi was wondering how to best do the inside and what’s guage metals, was wow hat brand of quarter panels you used

Nice job though , deffinetly a clean job

@slow_restoration

3 жыл бұрын

Thanks 👍

Thank you.

O ps I also subscribed and like your video 👍first time on your channel , not many people can say that they can do what you just did

What did you use to paint your frame and also how is it holding up to this day?

Excellent video thank you, I have the same job to do - suggest spraying interior panel with rust check over paint to deal with moisture, very effective at retarding rust, as I discovered too late

Awesome job . What would this cost if a local body shop did this , curious?

I just ran across this video. I don’t mind the talking part, but you did a hell of a job on the bottom rocker panels. I have a 2002 ram 1500 needs some work done just like that. Where are you located and how much would you charge for a job like that 👌🏼👌🏼👍🏼👍🏼???

This may be too late but my truck looks like this how much did you charge to do this job ?

HOLY SHIT IT'S RUSTIER THAN MINE

@slow_restoration

Жыл бұрын

It was bad!

I really enjoy speaking more about me doing mine

Great job my 2003 is looking something similar to this was just wondering how much would a job like this cost

@keith2860

3 жыл бұрын

Expensive if you have a place do it.

Would you do this again on a regular cab?

Great work!! I'd pay you to do my truck, where are you located?

How long did this take you to do the work in the video?

Out of curiosity how much does a job like this cost?

Nice work! Where did you purchase the rockers/panels from?

@slow_restoration

2 жыл бұрын

Thanks, the customer supplied the parts. I think LMC.

where did you order the middle panel from ??

Where are you located, I'll drop my 2004 off. It needs the exact same work and I'm not sure my skill level is up to the task.

Where did you get the rockers at? I’m looking to do this to my Cummins but everything I find looks different to what my truck needs.

@slow_restoration

3 жыл бұрын

Customer supplied the parts, I know some came from LMC.

What were the dimensions on that piece of 14ga sheet metal, I'm looking to get it for my truck. Thanks

Can you provide the link for the panels from the website you got those from ?

How long did it take start to finish?

Great video what did you spray on frame to remove rust

@slow_restoration

2 жыл бұрын

Pressure washed it, wire brush, then fluid film after blackening it out with paint.

Do you think you could have did the job without the middle part?

What were the dimensions of the inner outer metal you installed

What's the cost range for that kind of work

Do you do this as a business? I'd be willing to pay cause i've got a truck of a similar year that needs some repairs done to it

Where are you located and when is your next availability?

Nicely done. Question. Ive been looking to purchase the rocker panel pieces for my 2003 Dodge Ram. This is exactly how mine looks on both sides. Just to confirm, Id have to purchase the outer, middle and inner panels along with the corner cab? Also, do you recommend a website to purchase these panels from. Thanks. I just subscribed. Very helpful information and great channel.

@slow_restoration

3 жыл бұрын

Thanks! Yes, the outer and middle he bought. We couldn't find the inner to buy, I made them. The customer supplied the parts, I'm not sure where he got them. I appreciate the support!

@frankortiz5008

3 жыл бұрын

Thanks for response. Its good to see that there is people like you that still know how to work with metal. Cheers my friend.

@chrisperis5300

3 жыл бұрын

LMC Truck sells outer and middle, but no one sells the inner, gotta make it out of sheet metal.

@edjonatchick

Жыл бұрын

@@chrisperis5300 Thanks!

Where did u get that panels feom

Where did you order the full inner and outer rockers?

@slow_restoration

3 жыл бұрын

Customer supplied, I think LMC though.

What type of welding equipment did you use

@slow_restoration

11 ай бұрын

Miller mig welder.

Hey do you think you could link me or tell me where you got all the replacment panels im going to do the same job on the same truck and having trouble figuring out where to get all the pieces i need. thanks,

@slow_restoration

3 жыл бұрын

The customer supplied the parts, I'll have to check with him.

@christopher_performance8293

3 жыл бұрын

Mill Supply Inc in Ohio I buy mines right there Nice video I go to start mine tommorow

How much does a job like this cost?

Dodge really cheaped out with the sheet metal AND anything they called a coating! Coating attracted rust rather than preventing it. Never ever again!

@joshuaquilliam2887

Жыл бұрын

That and that stupid tape they put on the inner rocker holes. When I bought my 05 pieces were missing and within a year of winter the inners were rotten. I wish Dodge could build a truck to match the Cummins. I love everything about the truck except the cheap Mexican sheet metal.

@218philip

7 ай бұрын

I believe that they are spec’ing the sheet metal to corrode.

I would like the dimensions of that fourteengage iner rocker panel. You made that would be so awesome. Cause I'm doing my mega cab 06 dodge Ram. Any help would be greatly appreciated.

@slow_restoration

Жыл бұрын

I don't have any, I just used the truck itself for measurement's and had a local metal shop make it. Thanks

@tone569

11 ай бұрын

Do you have to take off the doors ?

@slow_restoration

11 ай бұрын

@@tone569 I didn't.

@tone569

11 ай бұрын

When welding the inner rocker cab sill that you made did you butt weld it i am having a metal fabercating shop make them

I’m about to do this on my cummins any suggestions?

@slow_restoration

3 жыл бұрын

Try and get as much of the rust as you can and seal it up!

Im going to build panels out of core 10 steel.

Where did you get the panels from?

@slow_restoration

2 жыл бұрын

Customer supplied them. I think LMC?

How much did you charge that customer to do that work? I need the same done to my truck lol

@slow_restoration

3 жыл бұрын

Not enough, it was a lot of work!

Hey I always go back to watch this video. If you feel like making extra money You can work on my truck.

Do the batteries have to be disconnected?

@slow_restoration

2 жыл бұрын

I didn't.

Looks like a 30+ year old car as far as the progression of the rust goes...

@slow_restoration

2 жыл бұрын

It's the mid 70's all over again with these things!

My wheel wells are rusting on my 2010 Dodge it suckso

Where are you located?

@slow_restoration

Жыл бұрын

Southern Pennsylvania.

Hello how much do you charge? How can I contact you?

Why is it not on the lift? Your gonna get old fast on the ground.

@slow_restoration

3 жыл бұрын

The lift arms get in the way, it's kinda a awkward spot.

@JohnDoe-fg2oq

3 жыл бұрын

@@slow_restoration Duh, I forgot about that. LOL

You could have but welded the rockers on then it wouldn't need but a lite coating of filler only . That's what I would have done and I have been a body for over 21 years

They are engineering vehicles to disintegrate, a half competent engineer could make it last 25 years in a Minnesota climate. When paying 60 thousand + for a truck, this is shameful. My 2014 ram has this exact same problem,,,,,, 9 years old!

you should film the work. not you talking about it.

What is shit crap design!😱 Nice job boss. better than new.🛠🇺🇸🛠

just get used doors

@bgt63

2 жыл бұрын

The doors look good...must have done them already

Not the best work for sure!

Throw that junk dodge in the scrap yard with all that rust lol. 🤣 that’s why I hate dodge rust way too much too fast.

@slow_restoration

3 жыл бұрын

They all rust, but some do seem to rust faster!

@2006pete379

3 жыл бұрын

Yeah, but the 5.9 cummins will outlast the all!