Ganz lieben Dank für das teilen der Datei. Diese Informationen sind sehr hilfreich. Toller Kanal. Schöne Grüße aus Deutschland

@MonkeyWoodworks

4 ай бұрын

Thank you for your kind words. You are welcome.

Thanks, Just getting started with my P2. Very easy to follow your instructions! And, I appreciate the files !

@MonkeyWoodworks

4 ай бұрын

You are welcome! Glad it was useful.

Thanks for taking the time to make this video. Much appreciated! I saw the first video and had my fingers crossed for this one.

@MonkeyWoodworks

4 ай бұрын

You're very welcome!

I can’t find the SVG file for your leveling tool! Could you please tell me how to get that! Looks amazing!!!

@MonkeyWoodworks

2 ай бұрын

Expand the description of this video. Scroll down to my Material Settings document. Inside that document, you will find lots of helpful info along with a link to my leveling tool SVG.

Hi, great couple of tumbler vids, I subscribed. Can you share the SVG of your leveling tool?

@MonkeyWoodworks

2 ай бұрын

Thank you for your support! Expand this video's description, and you will find a link to my Material Settings Google document. Inside that document, you will find a link to the file.

@llmcclymonds

2 ай бұрын

@@MonkeyWoodworks Thank you so much!

@MonkeyWoodworks

2 ай бұрын

@@llmcclymonds Absolutely

Maybe you can clear this up for me. The green line is on the far side of the tumbler. I seen other videos say don’t move to the center of the tumbler because of the camera. One video has the plastic center marker that goes on the rotary to move the line. What is the best way to get a good full wrap?

@MonkeyWoodworks

4 ай бұрын

I just go off what I learned from the developers during the testing of the P2: 1. Place tumbler in P2 so that the laser dot is at the highest point of the tumbler. 2. Perform an auto-measure in XCS 3. Position the engraving project just to the right of the line in XCS verifying the vertical placement. 4. Verify your engraving parameters (speed, power, lines per cm, etc) 5. Start your engraving. They told me: "DO NOT MOVE the line in the software. The line will automatically be placed at the highest point of the tumber during the auto-measure process." So since then, I have always done it that way and have not had any issues aside from hitting the tumbler tabs now and then due to dumb mistakes on my part.

What engrave air assist percentage do you use

@MonkeyWoodworks

Ай бұрын

Expand the description of this video. Scroll down and find the link to my Material Settings document. Inside that document, you will find my air assist settings used for engraving and a lot more.

Can you please confirm if the automeasure is to the actual top of tab itself or the area between the tab and where the edge where the tapered section starts. I'm a bit confused, if I automeasure to the top of the tab wouldn't the focus be too far off for the other areas of the tumbler ?

@MonkeyWoodworks

3 ай бұрын

I measure to the top of the bent over tabs. You can make it a little easier to get that measurement by putting a large piece of painters tape from tab to tab and measure to the middle of that tape. Using this method, i have not noticed an issue with the paint not burning all the way through. Now, there is a new method people are using by replacing the stock lens with a longer focal distance lens. This does require manual adjustments after auto measuring to account for the longer focal distance but it also allows puts the laser further away from the tumbler so you do not have to bend the tabs over. I have purchased a 3rd party lens but not tried it yet. Even with the 3rd party lens, you still have the issue with focusing on one area that is closer to the laser and hoping the tapered area also burns cleanly.

@adolfocabral9420

2 ай бұрын

​@MonkeyWoodworks where can I get the lens with the longer focal length? What's the size/name of it?

So even with the technical change in distance at the bottom end of the tumbler, no adjustment is needed?

@MonkeyWoodworks

4 ай бұрын

Not that I know of. You can see in the video that i have the ends level and I auto-measured at the highest point (the tabs). The method just seems to work.

@elissitdesign

4 ай бұрын

Yah! I'd think the focal plain of the laser would produce a poor burn, possibly not removing the powder coat. It's about 10mm distance!

Help, what kind of settings would you use on a M1?

@MonkeyWoodworks

3 ай бұрын

Check out any of my M1 videos. Look in the description of that video and find the link to my Material Settings Document. There you will find the settings I use for my 10watt M1.

@p3v4

3 ай бұрын

Thanks

@MonkeyWoodworks do you sell your file for the piece that holds the leveler? The video at approx 9:40 the file will be linked below but I can't find it. Thank you

@MonkeyWoodworks

4 ай бұрын

The file is free. See the video description for the link to my materials settings document. The link can be found in that document.

@RNMEDIC1335

4 ай бұрын

@@MonkeyWoodworks thank you

@MonkeyWoodworks

3 ай бұрын

You are welcome

Would this work on the M1 also?

@MonkeyWoodworks

4 ай бұрын

Yes it will. The settings will be a bit different but the process is similar. The advantage of the M1 is you can run a frame of your project to make sure it all works.

Hey Michael, another brilliant Tumbler video. I can't see where the link is for your levelling SVG. Am I missing it?

@MonkeyWoodworks

4 ай бұрын

Look for "My Personal Material Settings" in the description of this video.

@dickywyer293

4 ай бұрын

@@MonkeyWoodworks found it, appreciated buddy. Keep up the great work.