Hey Michael, I have been a software developer for 43 years. Usually whenever I see someone explain bit depth I see someone struggle, use confusing verbiage, or wanting to move on to another topic. On a few very rare occasions you see someone explaining it very well. You did it very well.

@vladimirseven777

4 жыл бұрын

Except he didn't. Old 8 bit processors used in consoles had 8 bit registers and 16 bit addressing so they were not actually completely 8-bit CPU. And he comparing CPU speed 100 MHz vs 16 MHz and deciding "32 bit better". Use 8-bit at 100 MHz and you will have more than enough CPU speed for printing.

@louis-ericsimard7659

4 жыл бұрын

@@vladimirseven777 This is not the case for all old 8 bit processors; for example the 6502 did not have 16 bit addressing. What you are referring to are extensions to 8 bit memory spaces using bank switching in order to save costs or implement features ahead of their time. That there are exceptions and additions to an evolving design does not make the explanation of the basic design faulty.

@vladimirseven777

4 жыл бұрын

@@louis-ericsimard7659 Not faulty, but very incomplete. Like modern AT-mega or Arduino are the same as old 8-bit processors. Bank switching in 16 bit processors was implemented to address memory above 65535 while pure 8-bit can address only 256 bytes.

@vladimirseven777

4 жыл бұрын

@@StavrosKor It depends from application. For example if used for temperature measurement or digital to analog conversion 8 bit data bus or data width used in CPU it limited to max 8 bit capacity - from 0 to 255 (256 states). 16 bit (65536) or 32 bit (somewhere 4 billion +) - you can use better precision, for example work with 0.001 of temperature. But right now 1C degrees (for example from 20 to 275C) or stepper motor drivers (max 256 microsteps) seems enough.

@ald3nt3

4 жыл бұрын

@@vladimirseven777 That isn't true. You can basicly calculate everything in an 8bit processor to the same precision a 32bit processor can by concernating the calculations using things like carry-flags. The only problem is, that it takes a lot more clock cycles for your calculation. Modern 32bit CPU, like stm32, also come with an FPU (floating point unit) which handles floating point operation in much less cycles that the standart ALU of the Arduinos ATMega2560. Problem of the stepper driving is that the Software on a 8bit processors in use aren't able to drive more that 10.000 steps/s due to lack of ressources with the workaround of sending multiple steps at once to reach up to 40.000steps/s. This method is called double and quadstepping which you can find in configuration.h in the marlin files and produces an absolute horrible sound, vibrations and possibly steplosses, as seen in the video. More than 40.000 isn't possible at all without disturbing the whole software loop comprising things like closed loop temperature regulation, watching for endstops being hit, safety loops (temperature runaway)etc. Having 80steps/mm for X/Y axis at 16µSteps limits your movement to 125mm/s (=10000/80). If you increase the steps per mm by increasing the µStep-Number to let's say 256µSteps like the TMC allows you to do, you would be limited to ~8mm/s.

Very nicely done, Michael! This level of tutorial, first generic, then specific to 3D printers is just what the community needed. The level of information is perfect.

Just bought the same board for my Ender 3. Been putting off swapping it in, but there's no excuse now. Thanks for your hard work! Your channel is awesome.

Perfectly explained as usual! Very interesting and very handy to know the differences! Cheers!

Nice job! It is nice to see positive evaluations and learning for new folks!

Definitely helpful information for a lot of us! And now I know enough to know that I don't really need to know any more, for what I do. Thanks!

YEEEEEES ! I bought a SKR and i'm waiting to arrive! Your video is going to be super helpfull!

As always your explanations are great and simple to understand.

I would love to see a comparison between a 8bit system with klipper and a RPI and a 32bit board. To see how the 8bit board compares when the calculations are done on the rpi. And as always a good and clear video. Keep it up

Great topic and I really appreciate you guiding us into this new technology!

I'm commenting only for thank you for such a good job doing videos, not only this one but every other videos. Nice work! Really helpful for newbies like me. I appreciate it a lot.

I love the way you explain things very clear, concise and easy to understand

great video you are truly a great teacher in every definition of the word. stay warm Alex

Perfect timing, I just bought one for my ender 3 :)

This is the best description of how a microprocessor works I have ever seen!

This is why your channel is called "Teching Tech" I learned a lot. Thank you so much for this outstanding Content. Greets from Germany!

Another awesome video, going online now to order my SK board so I am ready to follow you and upgrade my Ender 3.

Just when I start doing my own research on the SKR. Thank you!

@BenCos2018

4 жыл бұрын

me also lol

Ordered mine last week, looking forward to the upgrade comparaison

Very easy to follow explanation! Easy to understand, I gues could be used even in schools. Great!

Another terrific video. You explain topics very well.

I agree with Louis on this. you explained a very complex subject so easily and clearly.

Nice intro Looking forward to part 2 Thanks for sharing :-)

nicely explained, thank you. This would be the first video I have watched that clearly explains the differences, drawbacks and complications around 8 bit vs 32 bit boards. Love your work, keep them coming. cheers..

Perfect !!! Just what i was waiting, how to install the SKR.

This has been explained so well, thank you.

Great video. Definite thumbs up for this one!

my friend you teach something i was not expecting, by the first time i really learn binare codification

Good timing, I bought the same board a couple of weeks ago and am just finishing installing it into my printer.

you sure did teach the hell outta that tech, cheers!

Your description of binary was amazing

4:50 if you already know what a bit is and want to skip to the part concerning 3D printers.

@FragBenitez

3 жыл бұрын

Thanks 👌

@MrPancakes98

3 жыл бұрын

Thanks man

Thank you for sharing you’re knowledge

Wow, you are smart about this stuff! Thank you!

Very Good content! I really like your channel with this type of content rather than the printer review. Keep it up and I will give you a shout out in my next

Thank you for the informative video.

Thank you for the clear explanation!

This is a great explanation 👍

Hopefully you can mention the TMC2209's that are coming embedded on some ender 3 direct replacements. Not even sure if it's fully supported but it's the cheapest/easiest way to push into 32bit boards with the ender series

Nice video! I'm waiting for skr mini e3 in ender 3 tutorial :)

Thank you for this video, I literally just asked a question about the difference between the boards and whether they are necessary on the facebook ender 3 groups.

We need 3d printer boards with 7 nm ZEN2 architecture, 64 cores and 8 ghz!

@mitchh6471

5 жыл бұрын

Max Lindner what would be awesome but total over kill but take a 1st gen core i7 980-990 extreme and turn it into a 3d printer all in one board. , octo-print , arduino ide, a slice of your choice fusion 360 and or what ever else you can throw at it. Even a high end 1st gen xeon. X58 chip set board or what ever. For the lower cost but way to much process power lol man that would be sick. I wonder if it could be done. I assume so.

@BillyBobJimPatton

5 жыл бұрын

@@mitchh6471 I have seen a similar thing done before by a friend. Take a look at Klipper firmware. It's general idea is process the print via a PC and pipe it to the Arduino in the printer.

@BillyBobJimPatton

5 жыл бұрын

You can run Klipper on a RPI. Or a high-end multcore workstation if you have one spare lol.

@maximilianlindner

5 жыл бұрын

@@BillyBobJimPatton I actually do have a couple of pc's standing around and collecting dust. William, I think this is one of the few occasions, where a youtube comment has given me the momentum to do something great!

@BillyBobJimPatton

5 жыл бұрын

@@maximilianlindner happy to have bucked the trend and give a useful YT comment. I should screenshot it and frame it as proof that it can happen haha I'd be interested to hear how you get on with trying it.

Your channel is great, thanks for the content. You are one of the only ones reviewing the A10M on KZread that I trust, because of that I have a couple questions. What are your thoughts on the Geeetech A10M after a couple months with it? Is it useful for single filament use too ? How is the maintenance ? Would you still recommend it?

Wow thanks for the review of my System Architecture class...

Quality content.. well done.

Excellent video! Subbed!

can u do a review of the FLSUN QQ 3d Printer? it also uses a 32bit controller

Great descriptive upload. Condensed too a T.

Muchas gracias por compartir tu conocimiento!

Wow! I just posted a request for this on Michael's Patreon Page. Now that is responsive!

@Mephiston

5 жыл бұрын

He was probably already working on it.

Awesome video. Would you recommend a 32-bit board, such as the SKR 1.3 as an upgrade for an Ender 3 (Pro) ? Purely looking at it from a perspective with whether it will improve print quality or not?

Great explanation Micheal, Can't wait for the next video, it's the board that I plan to put in the Borg. Do you plan to cover using the E1 for the second Z motor? I haven't even touched Marlin 2.0 yet, but will be having a practice soon ... after your video

Would your next video for the ender 3 also work for the ender 5? Great work btw, newly subbed, and new to 3D printing, you've help enormously

I really enjoyed this video, I think it's a great tutorial on why we might need 8 bit versus 32 bit, and I was pleased to see you mention how stepper drivers with higher resolution can aggravate this need. I do have one criticism though, the H-bot style such as the Ender 5 is still a cartesian kinematic, the Y axis just moves the X gantry instead of the bed, and isn't harder to calculate. Spot on about the CoreXY and Delta style tho.

@TeachingTech

5 жыл бұрын

I don't own any h bot machines but I was under the impression two stepper inputs were needed for most movements. I may in fact be wrong, no problem admitting that.

@JoshMurrah

5 жыл бұрын

Teaching Tech hey so I think I am in the wrong - I just saw you seeming to refer to the Ender 5 as H bot which it is not. So all good! Good video thank you!

Is there any tutorial for building that awesome LED light in the background?

question any advice on how to reduce that vertical line that shows up on prints. because when printing circles it's a noticeable factor that effects tolerances just enough to not get smooth fits. I think it's from extrustion where the printer stops and starts. Also i use cura, because ya.

@tiaancordier3798

5 жыл бұрын

Change Z Seam in cura to random to get rid of that line

@fabiogarcia1431

3 жыл бұрын

@@tiaancordier3798 This does not solve the problem, just mask it, because the stopping point of each layer will be distributed randomly, leaving small dots all over the print surface. I think the better way is to sand that vertical line to get rid of it.

I am waiting for a board featuring an ATSAMD51, preferably done as drop-in replacement for the Ender-3.

You should do a test of showing print quality differences as well, especially when using some of the smoother drivers such as 2208

My CNC mill runs on an FPGA (smoothstepper) because it is more able to kick out the steps at regular timing with the chip set up specially for the purpose. Are there 3D printer boards that use FPGA?

Nice video as usual. When can we expect the video on the SKR 1.3? Thanks!

@TeachingTech

5 жыл бұрын

Monday morning Aus time.

omg, Alex kid! You gave me a nostalgic heartache😢

Hi @Teaching Tech, did you heard about klipper? Great way to re-purpose 8-bit hardware as kinematics are run in another device like a raspberry pi.

This video is great with lots of information. Would you know which bit control board will work for mixing extrusion commands (concurrent feeding of 2 filaments in 1 hot end)? I am using Creality CR-X Pro printer with Marlin 2.0 version firmware. Printer has Creality V2.2 ATmega2560 processor control board. I assume it is a 8 bit board, would it require 32 bit board to execute mixing commands?

@Teaching Tech Actually 8/32 bit is not really the precision of the ALU but the width of address map. For a controller it is called x bit only because the address map is x bit width - more the 'x' means more memory it can address. Page 17 of the datasheet - datasheet.octopart.com/LPC1768FBD100,551-NXP-datasheet-8326490.pdf

Hi, have you tried using klipper with octoprint and ender 3, I managed to get faster prints but not so clean do you have any comments or advice??, congrats on your channel by the way

good job man

Re the CNC are you going to do a video this, I've have one but it plunges down when starting

@TeachingTech

5 жыл бұрын

I have a video coming up soon. Done some hello world cuts with no issues so far.

Have you made any video about microstepping and what you can gain/cons?. Now with access to Skr 1.3 32bit and 2209's maybe that's a path to take? What would going all 1/32 stepping do for example?

What are the pros and cons of an skr 1.3 vs the new creality 1.1.5 silent board on an ender 3?

Thanks for the video, great job! could you do a video of marlin setup for Delta style printer such as Monoprice mini delta. My MPMD controller died lost the hot end temperature control. and the controller board is currently out of stock. I know these videos are a lot of work but they are of great worth for those of us who don't have the expertise with firmware builds. There are a lot of problems & fixes that this would help solve on the MPMD as well! thanks in advance!!!!

Those leftover 8 bit controllers also make really sweet general purpose Arduino compatible dev boards.

My favourite analogy is to say that going from 8-bit/16MHz to 32-bit/72MHz is like going from one milk-float at 15mph on a country lane, to four minivans at 70mph on a four-lane-wide highway. The bigtreetech SKR-mini-E3 looks interesting btw - $30 drop-in replacement for Ender-3/5, using a 72MHz ARM Cortex-M3 processor and soldered-on TMC2209 drivers - a real winner, I think.

Are but what about the multiplexers or the DACs ? Good work on the basic electronics.

[Being pedantic for fun, not to be a pest] There are actually analog computers that aren’t base-2, but I don’t know if they’re still used anymore. In addition, many SSDs are actually base-4 or even base-8, meaning each memory cell stores two or three bits at a time. Explaining Computers has a very good video about this discussing the new Samsung QVO 3-bit SSDs. Love your work, keep it coming. 🙂 I know I’m commenting on an old video, it’s just how I roll. ;)

when using octoprint does the processing still happen on the mainboard or the pi? if its all done on the pi would 32bit vs 8bit mainboard be irrelevant? you make awesome vids that help a lot.. thank you..

Ok quick question which would be better i have ender 3 pro and want to be able to print PETG and Nylon. So should i get the SKR or The duet. And i also want to throw a touch screen into the mix. Not sure if SKR can handle the add-ons for the high temp settings and LCD. Also all the duet 2's on Amazon say cloned is this ok or should i get right from the duet's website?

Hey i have an Ender 3 Pro with the old Board. Will it improve Print Speed and Quality if i upgrade to this Boards or is it only Noise REduction and more Functions like Auto Bed Level and other stuff? Thx 4 Answer and nice Videos man

What about an accurate pinout for this board? Please include some info on that in the next video. The information for this board is so hard to find! Thanks for the great content as always!

Hey Michael, A question for you. Have you any ideas on reducing bandwidth issues with printing over USB? Currently i run 5 printers all running off 1 linux server which runs 5 instances of octoprint using docker. All 10 usb ports on the machine are used, 5 printers, 5 webcams. I don't really notice much issues but 4 of the printers are identical, same firmware, same upgrades and often i find one or 2 of the printers will finish first by upwards of 30 mins running the exact same gcode and my only thought process is that somehow the usb overhead is slowing down the gcode processing to some of the printers? are there any boards that have usb 3 on them? is there any particular board upgrade that will limit this overhead? will a 32bit board solve this? thanks for any info mate.

I was thinking a long time to upgrade to the MKS gen L but up until recently i wont. i will use the SKR 1.3 because 2 killer features: SD card and 32 Bit proccesor

@KamilxxG

5 жыл бұрын

MKS Gen L can have sd card. It requires to buy SPI card reader for $0.5, connecting it to AUX3 and some small change in marlin.

With the update of the MK3S+ to MK4 from Prusa, can you make an update on your notes?

Your review of 8bit vs 32bit is nice. Thre are limitations of 8bit it has been known for a while. Expecially with matrix bed leveling and linear advance adding a lot of overhead into the movement. Most 8bit setups are running a RPI 3B+ with octoprint to make life easier transfering files wirelessly. If we use the RPI processing power for running Klipper so all data processing is made by the RPI we can print to a very high microstepping. The limitation is made by the transfer speed of the arduino USB. Its a little lower than the processing speed of your 32bit but a lot higher than what 8bit can handle.

@TeachingTech

5 жыл бұрын

I have two klipper videos coming up. Thanks for sharing.

@Side85Winder

5 жыл бұрын

@@TeachingTech from memory a 8bit system with 1/16 steppers (a4988) tops out around 160-180mm/s. With a ABL and linear advance its around 120mm/s which is still a lot higher than most users print at. Using klipper a arduino has 115200bps baud rate. Since we are only sending move data and sensor information we can use a ABL and LA and still print upwards of ~200mm/s.

Is the upgrade creality mobo with tmc drivers 32 bit?

@ImGriffinP

5 жыл бұрын

no. and it's a bad 8 bit board too. it isn't designed for the trinamic drivers so they overheat.

So is the controller in my Anycubic Linear Kossel 32 bit? I loaded Marlin 1.1.8 onto it about 8 months ago and now it's dialed in its completely dependable and delivers high quality prints. Same with my Ender 3. I know it's got a cheap-ass 8 bit board but it works well. And there is the issue. My interest is not in building the best printer but in having reliable printers to output my projects. They are both dialed in such that I rarely have to level them and I'm not sure screwing around with the controller will give me additional value. Maybe I need to build a delta from scratch.

@TeachingTech

5 жыл бұрын

If it's reliable and printing to your satisfaction I would leave it.

@68HC060

4 жыл бұрын

As written above, I think the rule "If it ain't broke, don't fix it" applies in your case. -You're already satisfied with the prints, which means it might not be worth all the trouble and frustrations upgrading. But at a later point, when you think your Kossel is no longer an interesting piece of technology, you could upgrade it to a 32-bit board, which should then give it 'new life'.

Awesome & timely video Michael. I am considering using Marlin 2.0 to help implement BLTouch. But I am afraid the ENDER-5's Sanguino board might be incapable of supporting Marlin 2.0. Is the MKS Gen L board a better choice; or something else. Maybe I should stick with Marlin 1.1.9 on my Ender-5; and look at Marlin 2.0 for my next printer, down the road ..... I look forward to your advise.

@TeachingTech

5 жыл бұрын

I haven't tested marlin 2.0 on an Ender board but on paper it should be fine. The Gen L is superior in every way to the Melzi, but there isn't any need to upgrade unless you want to use more IO pins or change stepper drivers.

Would upgrading to a skr 32bit board allow me to add an additional excruder with an 2-1 hotend on my ender 5?

@TeachingTech

5 жыл бұрын

Yes, as would MKS Gen L. It's because they both have extra stepper outputs and thermistor inputs.

@emmanuelgonzalez3635

5 жыл бұрын

I am thinking on using this, www.amazon.com/dp/B07R3VVJN4/ref=cm_sw_r_sms_apa_i_R5DfDb7BEW008, Do you think it will work for the ender 5?

The last 32 bit upgrade I did from an 8 bit board was about a 25% speed improvement using the same gcode file with the 8 and 32 bit boards. One of the things I noticed was the 8 bit board had a very short delay between gcode commands and that disappeared on the 32 bit board.

@TeachingTech

5 жыл бұрын

Very interesting, this is something I have to test.

@68HC060

4 жыл бұрын

In the future, when slicers and printing algorithms become more sophisticated, expect a much larger speed difference. In particular, I'm talking about smooth surfaces formed by arcs rather than lines. Cortex-M microcontrollers spend only one clock-cycle for multiplying two 32-bit numbers (with a 32-bit result), whereas an 8-bit MCU would need at least 19 clock cycles, so a single multiplication would thus be 19 times faster if it's 32-bit. For things like arcs, you'd use multiplications a lot. Cortex-M4 and M7 have a floating point unit in addition, which means one can take advantage of a built-in square-root instruction (which can be used to calculate distances between two points - this will probably not be used in the near future, though). A simple MCU like STM32F103C6 has 20KByte RAM and USB interface; this IC can be acquired for less than US$2. An 8-bit Atmega usually cost more than $2, and most of the boards I've seen for controlling 3D printers and CNC-routers use some CH34x or PL2303 chip on the UART to get USB functionality. This requires more PCB space and also more ICs (which means extra shipping cost for the manufacturer); it all adds up. So even though the STM32F103C6 is only 72 MHz and only has 20K RAM, it'd still beat the 8-bit AVR in every case I can think of. The STM series also have some sophisticated motor-control features (which have not really been taken advantage of in any PCBs I know, since all of them use standard stepper drivers).

I'm buying a laser engraver and I'm wondering if anything is stopping us from flashing grbl firmware to an skr board? Run a laser engraver using a 3d printer main board?

Great video. I'm wondering which drivers, TMC2209 or TMC2208?

@shadow7037932

5 жыл бұрын

Not a ton of differences between the two as far as usability goes for 99% of the people/setups. Get whichever one is cheaper.

can this same board be used for cr10? thax

I have a monoprice maker select plus, basically a wanhao duplicator I3, and was wonder if this board would be possible to retro fit into my printer, I'm not happy with it and doing research on turning it I to what it should be

@TeachingTech

5 жыл бұрын

I have the Cocoon clone of that printer. The sticking point will be the ribbon cable attachment which is different to other prints. You would need to cut and terminate the wires with jst connectors or make a break out board.

@MrShadowchsr2

5 жыл бұрын

@@TeachingTech I have seen your video with the Cocoon, tinkering to make it work would not be a problem, curious if it was possible to make it work. I basically am unhappy with my printer and I want to work with it and turn it into something better cause that's just me, tinker with something till I either break it or enhance it ha ha.

Does the controller actually do the displacement computations or it's made by the slicer when creating the g-code file description of the model? It seems that the controller computational work is mostly restricted to the gcode file parsing (a translation with no math involved) and not actually to compute step motors displacement commands. I think It only computes inertia (when and how fast step motors should be moved) and PID temperature control and this suspicious came to my mind after trying Klipper. In Klipper, the parsing work is done by the RPi and the motors pulses sent directly to the stepers using a daemon running in the controller.

@TeachingTech

5 жыл бұрын

Gcode only does so much. It will say move from here to here but that doesn't account for acceleration or anything like that. Consider that the gcode is the same for a Cartesian printer vs a delta despite the greatly differing maths required.

3:02 Surprised no one's pointed this out. N digits of binary can represent up to 2^N values, and thus 8 bits can represent up to 256 values (0-255 unsigned). Early computers represented negative integers as described here, called signed magnitude representation-- one bit is reserved for positive/negative, and the rest is used for the number's value. However, modern computers represent negative integers differently, and 8 bits can represent 256 values (-128 to 127). This happened partly because of the cost of transistors in the early days of computing, and partly because it was kinda silly to have both a positive 0 and a negative 0. en.wikipedia.org/wiki/Signed_number_representations#Two's_complement Signed magnitude representation didn't catch on for integers, but it lives on in modern floating point (IEEE 754). Floating point does have a positive 0 and a negative 0, and they're used in cases where, say, a mathematical function has a discontinuity at 0. 1 divided by x, for example-- approaching zero from the positive side of the X axis, it shoots up to positive infinity, whereas approaching it from the other side, it falls off to negative infinity.

@79DJB

4 жыл бұрын

Morio, I got to 3:15 and went nope, 2s compliment. I'm an embedded designer.... Apart from that, great explanation

Would be very interesting to see a full comparison on a Tarantula Pro or an Ender 3... Stock vs 32bits vs Klipper

What about laser engravers or cnc machines?

The Marlin page shows that the HAL for the $38 Adafruit Grand Central M4 (ATSAMD51) is in development.. bus that doesn't have any SD card (for the g-code), nor as many I/Os as the MKS-Gen-L-1.0.. how will that work for 3d printing? Shield?

Ok... but what does upgrading my 8bit ender3 to 32bit give me? Are the prints better?

@68HC060

4 жыл бұрын

Should give you about 25% speed increase and likely better quality - also I'd bet on the 32-bit horse for future expandability (eg. expect future firmware to run on 32-bit microcontrollers when 8-bit has too little program-space).

can i put duet 2 on tarantula pro? i cant find guide

You didn't show a demo of 32 bit Mcu overcoming the challenges in a 8 but mcu

So can we use marlin and get ability like klipper?