3 Easy Steps to Stop Rust - How to Apply Rust Encapsulator Plus to a Rusty Rear End - Eastwood
In this video Joe removes heavy rust, dirt and grime so he can apply Rust Encapsulator Plus to a Camaro rear end.
BUY Rust Encapsulator Plus - www.eastwood.com/eastwood-rus...
Eastwood has been one of the leading names in rust prevention for many years. Now we bring you twice the corrosion resistance of our original Rust Encapsulator in a simple to apply moisture cure coating. Spray it, brush it or roll it on. It does not matter, just get it on to protect your next project from corrosion.
RUST ENCAPSULATOR PLUS FEATURES:
2X Stronger Than Original Rust Encapsulator
Passed over 1,000 hours of salt spray testing
Best used in Non-Direct Sunlight Applications
Should be top coated in Direct Sunlight Applications
Direct to metal or apply over rust
Heat Resistant Up To 350 Degrees F
Only one coat required for full coverage
Easy Application: Roll, Brush, or Spray
ONE TIME SIMPLY APPLICATION LAST FOR YEARS
Use to protect or restore car frames, boat trailers, utility trailers, outdoor metal furniture, mailbox posts, bilco cellar doors and more!
Better than hardware store aerosols
Outperforms all competitors and heat stable to 350 degrees F
Only 2 quarts required for full size car or truck frame
Looks great or topcoat with your product of choice
• Matte Black Finish
• Single component aluminum pigmented coating
• 67% solids by weight
• Approximate coverage: 96 SQ FT per quart for one coat
• Proprietary additive increases product adhesion to rusted steel substrates- unmatched by competitive coatings
• 1 coat assures maximum protection
• Brush, roller or spray applied
• Paint Gun: HVLP gravity or siphon with a 1.4 minimum needle/nozzle
• Re-coat able after 4 hrs.- if top coating after 48 hrs., scuff surface with 320 grit paper
• 2 hrs., tack free
• Easy to apply
• Topcoat able with virtually any high-quality coating
• Maximum service temp of 350° Fahrenheit
Recommended Substrates and Prep
• Apply product as a primer/Encapsulator over clean or corroded (rusted) steel or cast iron
• Prep surface by mechanically cleaning loose flaking rust with a stiff brush or wire brush/wheel
• Remove any grease, oils or other surface contaminants with a solvent such as PRE or Acetone
• Apply by brush, roller or spray
For more information on Eastwood products visit www.eastwood.com or stay connected with the team via:
Facebook - / eastwoodcompany
Instagram - / eastwoodco
Blog - www.eastwood.com/blog
Since 1978 Eastwood has been supplying products to the people who want to do the job right. Eastwood offers a complete line of hand tools, welders, plasma cutters & accessories, metal working tools, powder coating supplies, paint and paint guns, specialty paints and hard to find products, all for the DIY-er. Eastwood has all the tools and supplies you need to restore your car, truck or motorcycle.
Пікірлер: 94
Power. Washer. FTW. 5 minutes instead of 5 hours.
20 bones on a power washer and degreaser off camera, that surface was immaculate before coating.
I'd be 70 times more Interested if the vague marketing ploy of 2x nothing actually gave me a idea of how long this lasts
Oh my! Not a little wire brush right out of the gate. Get that outside and hit with a pressure washer. Then spray degreaser, use a bristle brush and then pressure wash again. Then spray with soap and water, rub with a big bristle brush on a handle and then pressure wash again. Then dry with a leaf blower. This saves me hours.
Nice thanks
Why did you paint the drums? They are consumable and they dissipate heat. Does painting them not compromise the heat release properties leading to breake fade/failure? That seems dangerous to do (especially by professionals). Please correct me if I am wrong.
Arent all paints rust encapsulators? I'm not seeing how this product is different than normal tremclad. You painted it black, big whoop. :(
I still like to remove as much rust as I can first and use an encapsulator after. I just do a basic job of removal though. A little bit of initial work goes a long way. Is a couple hours of grinding vs. 10 years of protection worth it? It is to me. This stuff looks amazing. I'm going to have to pick some of this up. Anyone want tp buy some implement paint?
Looks like he painted right over all the oil leaks that were on the diff
I used this stuff to do my sandblasted frame. It’s sticks to the metal really good. Even can’t get it off of my hands. Hope it will last for a long time
That’s what I’ll b doin this weekend. Thanks
Will spray on bed liners like Raptor liner adhere to this or is a primer needed on top of this first?
Does this convert/ primer the rust? Can I use a converter/ primer first that will turn it black?
You have the patience of Job.
💥 What’s the difference between the encapsulator vs the converter.??
I bought both eastwood rust converter in a spray can an eatswood rust encapsulator in a spray can.
What do you use to clean up the brush after your done? Will regular paint thinner or mineral spirit's work?
Wish I would of thought of using this, don't know why I didn't. Took three days rolling around the ground cleaning my diff and just spray painted it. Oh well
Do I have to sand after 48 hours to topcoat? Or can I just apply topcoat. It's a large are with nooks and crannies to sand
Can this be used on brake lines that are still sound but have a rust coating? If not what can you recommend?