Update: The Q12 is not to be seen as an UPGRADE to the K688’s own built-in audio interface, which is arguably better because it has no interference/static. This video was released right after I got the K688 and when it appeared that the pops and clicks on it were due to its internal parts. I even bought a second K688 and the distortion persisted in that one. I later found it that the issue was that the included cable in the K688 was a USB 2.0 cable. You need to get a USB 3.0 cable. (Note: USB-C is just the shape of the connector but does NOT guarantee USB 3.0 speeds. The included one had a Type-C end but was 2.0). However, the Q12 is still a handy interface to have, as it lets you play back your computer audio, record more than one mic input, and is relatively more affordable versus higher-end interfaces so you can become familiar with how an interface works. I know I avoided interfaces for years and stuck to USB mics. If the Q12 at least lets you understand how they work, and gives you the courage to get a better interface later, for $29, the added features and learning should make it worth it in the long run. If you want the first true upgrade to the K688, consider the Behringer UMC204 HD which has better preamps than the Q12 and converts the audio into 24-bit. If your use case is just gaming, you may not need that upgrade at all if you aren’t picky. For recordings, 24-bit gives you less distortion when you edit in post, a lower-noise floor, and more dynamic range. For a major upgrade to an interface with better preamps and features, consider the $199 Motu M2. I’ve used it around the clock for 3 years for all my professional voice over applications. My musician wife uses an SSL 2+, which performs similarly. Here’s my old (but still relevant) video on these interfaces: kzread.info/dash/bejne/iaJsrMx_p6-rZ9Y.html

@mixhaelcastro

11 ай бұрын

What usb 3.0 cable did you use?

@DaveSoltura

11 ай бұрын

@@mixhaelcastro I used the one for my iPad, but this should work! amzn.to/3Q3zshX

@ersamson

11 ай бұрын

Hi Dave, I was wondering about the USB drivers, if it's plug and play? I'm thinking of using one for my work laptop with a dynamic microphone, but I don't have admin rights to the device, hence no manual driver installations.

@DaveSoltura

11 ай бұрын

@@ersamson Plug & play in my experience!

@h1i0a

8 ай бұрын

@@DaveSoltura i hope you will reply to me I bought SoloCast for 5 months now and it’s very good i use it for chatting with friends and little bit of making KZread videos but when i play with my brother we are in the same room and chating with friends it will pick up my brother voice and make echo so I considered buing i dynamic mic fifine k669d ....... so is this interface will handle it + is my choice is good dynamic with this interface or in the beginning i want the vocaster one but is very expensive then the mic it self so I kept searching Edit or buying the maono pd100

Im getting one, thank you bro, best review ❤

Hi dude ! Great review ! :) Greetings from France, you got a new subscriber here. I love the vibes and your reviews are REALLY amazing. We get all the information we need and you seem really friendly, thanks and keep going ! :)

@DaveSoltura

Жыл бұрын

Thanks for the kind words and for subscribing! 🙂Comments like yours really make my day. I hope I don't disappoint you!

Subscribed for the enthusiastic and fun review. I bought a Teyun A4 already, and it's major fun. Found a Q12 and was slightly set aback by the lack of EQ. This review got me wanting it 😊

@DaveSoltura

5 ай бұрын

Thank you for the kind words. How do you like the Q12 va the A4?

@MarkusAudio

5 ай бұрын

@@DaveSolturaI haven´t tried Q12 yet, but A4 was a nice unexpected surpise in my last travel. Same Q12 features, plus a warm EQ, built-in Delay effect assignable to each of the mono inputs...and the ability for direct-to-USB drive mono RECORDING, abeit glitchy every 10 seconds. I Love it, and all those features packed in a Q12-sized device might make a future winner (TEYUN are you watching?)

Fantastic work my friend thanks for teaching me how to use the interface still im a neebie and not into interfaces..... i just plug the mic straight into the usb connection now im looking into getting and learn how to use professional audio system big thanks mate

I had my K688 for a few months now and haven’t considered going XLR until I saw this video. Bought it and waiting to be delivered today. Honestly excited to play around with it! Keep up the good work, man! 🔥🙌

@DaveSoltura

Жыл бұрын

Have fun with it! The Q12 is a great first interface to fiddle with to give you confidence for higher-end ones. 🙂

@just_tom00

9 ай бұрын

hows it been?

@alfredg.m

2 ай бұрын

So, how is it?

I love the audiophile nerds! Well done sir! Welcome to the club! 🇨🇦😂😳

Great review, Dave! Btw, you can use a USB hub but it should be the one that has it's own AC power supply. That's what I'm using.

@DaveSoltura

Жыл бұрын

Thanks, Allan! Glad it works for you! I do have two with their own AC power supply. Works most of the time, but they do fail at times when they’re overloaded! Had to redo some recording sessions just because they failed on me. In general, it’s good form to have fewer cables so as not to extend the signal chain. Every extra device is like adding a layer of slightly tinted glass, resulting in a blurrier image. Anyhow, that’s just a personal preference. If the hub works, it works!😁

@davidsanchezaraiza9889

Жыл бұрын

Can you tell me which one hub? Planning to do the same

I'm getting one Dave. Thanks for the great review!

@DaveSoltura

Жыл бұрын

Thanks for the comment, Iggy! I don’t consider this a full review yet… maybe in the future!

@Sins-x

Ай бұрын

How was the mic thinking about getting one

This looks really good! I'm considering to have my first audio interface because of this review.

@DaveSoltura

Жыл бұрын

Hi Ivy! That's great! If you're using a USB mic, it's really not all that different! You'll have more granular control over your mic. :)

@mreliaww9332

Жыл бұрын

Did you buy it am thinking too

@steelhead197

2 ай бұрын

It’s a mini mixer though? 👍🏻

Great review! Can you also play your PC audio thru this interface without mic monitoring?

Just so everyone knows what Dave is using is a mixer. When it comes to solo livestreaming or podcasting mixers are good enough. But if you want to record two audios and treat them as two separate tracks well you can't with a cheap mixer. There's a difference between an audio interface vs mixer. This Teyun is a cheap mixer and all input sound is mixed into 1 track. Only the more expensive multichannel mixers has multitrack/multichannel recording. An audio interface that has 2 inputs at minimum are treated as two separate tracks. Here's a scenario, for example, you have a podcast with a guest and both of you have individual mics, if you are using an audio interface with 2 inputs, your voice will be recorded as track 1 while your guest's mic will be on track 2, and each can be edited separately. If using a mixer, the sound from both mics will be mixed as track 1 and so you can't edit the two voices separately. Here's another scenario, you want to record a song while you are singing and playing an instrument at the same time. With an audio interface like Focusrite or Behringer your vocals and the instrument sound will be on separate tracks, but with a mixer both your vocals and the instrument sound will be mixed as one track, thus making it near impossible to edit the voice and instrument sound separately. If you are looking to record audio into separate tracks always look for multichannel or multitrack recording feature on any audio interface or mixer. Update: So Dave just checked if Teyun records separate tracks, and what do you know this mixer does! I stand corrected!

@DaveSoltura

Жыл бұрын

Can the Teyun Q12 record separate tracks? #audio #fifinek688 #microphone

@Mark_Sings

Жыл бұрын

@@DaveSoltura I stand corrected! Good to know that it CAN simultaneously separate tracks by pushing the ST Pan or To Stereo button before recording. Recent mixers from China has really gone a long way. Most cheap mixers cannot do multichannel recording hence the need for audio interfaces (or mixers with multi channel recording/stereo pan) to get a clean separate signal.

@Mark_Sings

Жыл бұрын

@@DaveSoltura Oh and this new reply is just further clarification for everybody to read. Just to expand on the limited capabilities of budget multichannel USB mixers that are more pricey than the Teyun Q12. Most (not all) budget USB mixers has a pan knob that does the same job as the ST Pan button on the Teyun Q12. You CAN record and separate a stereo mix into separate left and right mono signals but there are limitations when recording mixers via USB . Most mixers (not all) can only record 1 stereo track or push 2 separate output tracks since this is still a stereo mix even if you pan all channels left and right to separate the signals (2 mono in 1 stereo mix). A 4/6 input channel USB mixer can only push out a 2 output signal to the PC via USB ; you can do 2 channel in and 2 channel out but not a 4/6 channel in and 4/6 channel out. Audio interface doesn't have this stereo output limitation, you can record separate tracks at the same time, you are only limited to how many input channels you've got. Here's an article for full explanation: www.musicrepo.com/audio-interface-vs-mixer/ If mixer is still your thing, there are multichannel USB mixers out there than can do both worlds, hands-on hardware control and multichannel separate track recording via USB, just look at the manual or product description if it has this feature. Here are some: thehomerecordings.com/mixers-usb-multitrack/

@DaveSoltura

Жыл бұрын

@@Mark_Sings Appreciate the valuable, well put-together input!!

In Malaysia, it costs around 10-15 bucks. Thanks for the review Dave.

@DaveSoltura

Жыл бұрын

Insane! Yeah, in the Philippines, it's also about that much! Thank you for the kind words.

It was advertised as a mixer online so i got it and just made a mess. I connected it to my Scarlett solo so i am probably using 2 interfaces now. I should have done more research on my end but it works

I have a Teyun Q-12 and used instruments(Electric Bass) for it and its too quiet even with the highest gain and clips too much, when recording its not the sound you expect because i can't get the tone i want which has many effects. If you go overboard just a tiny bit white noise is apparent, its okay for guitars not for bass because of its low fequencies. For microphones and etc it does it job but definitely not for high quality audio which i believed in, its a great mini mixer to add your xlr mics in your desktop you can always adjust your gain in windows or Voicemeeter, Just don't buy it if you want a clear sound quality for recording and just save up and get a better one like focusrite or behringer Not gonna lie, its a trap for home recording BUT i suggest buying it first to know the basics of handling and working out an audio interface because its a whole mountain to climb tbh Edit: TIps for Buying Audio Interfaces - Even with a high quality brand there are certain models that are just bad - I suggest buying a consistent model or 2nd or 3rd model down - 2nd hand, please i suggest testing it yourself from recording , monitoring and latency, scratches dont matter its not a guitar anyways. Always ask the condition and problems for the audio interface.

48V power won't hurt a dynamic mic. It is absolutely required for condenser microphones. Where it might cause damage is on a ribbon mic. You would not be using this interface on a ribbon mic.

I just got mine recently, and here are some of the pros and cons. If you want to use it as a usb connector for your recording, it does it's job really well, but since the design is simplistic and minimalistic and its only features are gain and volume control I would suggest that you should pair it with a multi channel audio mixer or a soundcard that has vocal effects on it like reverb.

@curiousmusic101

3 ай бұрын

does it have its own driver? or standard ASIO4ALL?

@jeffrymanlutac

3 ай бұрын

@@curiousmusic101 What operating system you use? if it's MAC I actually don't know since I'm a Linux user but the Audio Interface itself is Plug and Play no other drivers that need to be installed.

Thanks for your review. Would be possible to connect the mixer to DAC L/R Line out and Active Studio Monitor to use the mixer as volume controller?

Awesome review! May I ask about the monitoring's latency? How well is it handled by this Q12? Is there a noticeable amount of delay because l'm looking for an affordable interface such as this one and latency is crucial for my recordings. Thank you so much Dave!

@DaveSoltura

Жыл бұрын

No latency issues in my experience!

@hiroyashii

Жыл бұрын

@@DaveSoltura thank you so much! awesome review btw!

I would like to see a dynamic microphone test connected via P10. I tested a condenser via XLR and it worked perfectly... A dynamic XLR also worked relatively well, but using the P10 connection, on the cable that came with my microphone, the sound was extremely low. Using this same dynamic microphone with the P10 cable on an Arcano Mini-M, it worked perfectly, so I know it's not the cable or the microphone. I wanted to understand if the interface is bad or if mine is defective.

@DaveSoltura

6 ай бұрын

Interesting idea! Something to consider!

Looks great. Quick question. I want to record videos with an iPhone 12. Can I plug the output from the XTUGA into my phone using an adapter?

@DaveSoltura

Жыл бұрын

Hi Rob! I've been able to connect audio interfaces and USB microphones to android phones since using microusb in 2017. But for any lightning connection, I haven't gotten any of those to work with my iPhones. Maybe it's possible, but it didn't work in my experience.

I just got mine on sale for $11 and free shipping.

Hey dude. I’m really struggling with this combo. The mic itself doesn’t sound horrible with XLR. But when I talk you can hear some sort of interference or it almost sounds as if a fan is blowing when I speak. Do I need to turn my gains all the way down and boost in OBS. I cannot for the life of me get audio sounding nearly as good as yours for live-streaming purposes.

@DaveSoltura

Жыл бұрын

Hi there! The interface really does have a bit of interference as I mentioned, but you can minimize this by maximizing your signal-to-noise ratio. I had a look at your channel and saw some of your videos. Your mouth is usually about a span away from the mic, which is quite far. When your mouth gets to about 3 inches away from the mic, that's when it would sound loudest, so when you boost it in OBS, the interference isn't boosted nearly as much. Check my other video on mic placement: kzread.info/dash/bejne/o3Vmyqlrm5bMYrA.html

@EErock

Жыл бұрын

@@DaveSoltura appreciate the feedback thank you

Hello! Would it also be possible to compare this Fifine K688 to Fifine AM8 usingthis audio interface? Btw you earned a sub, reviews are really good. Planning to buy this audio interface but kind of confused with Fifine K688 vs Fifine AM8.

@DaveSoltura

Жыл бұрын

Thanks for the kind words and the sub! I’ve added this to my list of reviews. :) Just a heads up that it might take a few weeks.

@kodzuken6314

Жыл бұрын

@@DaveSoltura thank you for the reply! Will definitely wait for this. Keep up the nice videos!

Hi, can this be used as a 3-channel mixer? What I mean is, is it okay to connect say a condenser microphone to that 1/8 inch (3.5 mm) input and a keyboard to the Input 1 (1/4 inch) with a guitar to the Input 2 (1/4 inch) all at the same time? If that is so, does the volume gain for Input 1 control the volume level for both the condenser mic in the 1/8 inch input and the keyboard in the 1/4 inch input at the same time? Any feedback here will be really helpful. Thank you very much.

Thank you so much. Btw could you please compare Teyun Q12 vs Q16? Is it an upgrade?

@DaveSoltura

Жыл бұрын

Added this to my list. Targeting to get this done in a few weeks!

@ngetnarin

Жыл бұрын

@@DaveSoltura Thank you. 👌

Wooow! Mind blowing!

@DaveSoltura

Жыл бұрын

I know, right!? Are you getting one? :)

Hey Dave! Your videos helped me decide on the A8, but now I'm looking for an upgrade, as the A8V picks up my mousepad noise when I talk while playing games (I have a glass mousepad 😅). Do you think the K688 + a Teyun Q12 would be enough to have clean audio while playing games?

@DaveSoltura

Жыл бұрын

Glad to be of help! The K688 + a separate USB 3.0 cable would be enough for “noise canceling” since it’s a dynamic mic, and the A8 is cardioid. Please read my pinned comment regarding the USB cable.

@sinxzyn

Жыл бұрын

@@DaveSoltura Thank you so much, Dave! I appreciate your work.

@masterchupoposkwentongbarb5105

10 ай бұрын

The USB 3.0 is Type C to Male? Or Type C on both ends? Thank you :)

@DaveSoltura

10 ай бұрын

@@masterchupoposkwentongbarb5105 Type C on both ends when not using XLR mode/when using usb mode :)

@masterchupoposkwentongbarb5105

10 ай бұрын

@@DaveSoltura thank you! :)

Even cheaper than the UM2!!! 😂. The UM2 is actually awesome apart from there are no official drivers left. They way it automatically bridges the microphone over left and right channels is good. I’m going to try this ultra cheap interface!

@DaveSoltura

Жыл бұрын

Enjoy!! Crazy what you get for the price!

Would recommand it over the Behringer UMC 22?

I´m planning on switch my Quadcast S into this mic and a Q22, because my Moba is having some white noise that is very annoying and i needed an external audio device to block it, what is not possible with a USB microphone

W video keep it up

Awesome and extremely informative video, thank you so much for making it! I ended up getting the exact same setup but am having an issue - my mic isn't receiving any/enough (?) Power from the audio interface. The interface is recognized by my PC, but when I plug the fifine mic in to the interface via xlr cable I get nothing - the mute button light is also completely dark. The mic works perfectly using the USB connection, do you have any idea what the issue could be? I tried different USB ports on my PC but I had the same result. Any help you could offer would be greatly appreciated. Thanks again for the awesome and informative videos!

@DaveSoltura

Жыл бұрын

Thank you for the kind words, and it sucks that it isn’t working… have you tried raising the gain knob, and is phantom power off? I would also try listening to the mic via the monitors, so you can determine if the issue is between the mic and the interface, or between the interface and the pc. If you can hear it via the monitors, then it likely has to do with the connection to the pc.

@parachute

Жыл бұрын

​​@@DaveSoltura yep, I've tried both of those things - playing with all of the knobs, listening for sound, ensuring phantom power is off etc. I noticed the mute button light isn't coming on at all when connecting to the interface via xlr so maybe it's just not getting power at all. My next step I guess would be to get a different xlr cable, because my PC recognizes the interface when it's plugged in so it seems like the disconnect could be there like you said. Or possibly do you think that the USB cable itself connecting the interface to the PC is having problems? Either way those are fairly cheap solutions I'm going to try today!

@DaveSoltura

Жыл бұрын

@@parachute Both of those are possible! Admittedly, the worst case scenario is that the interface itself is defective, but fingers crossed that’s not the case. Also, in my experience, the lights for the mute button don’t turn on for xlr mode. It’s as if the mic surrenders all controls to the interface in xlr mode.

Eyyy bro, I need you help, I listened thing like the OBS audio it’s sounds different, and depending the software are you using, the microphone quality could change. My question is, what application are you using in this video? Audicity? Or what. And which settings are you using too

@DaveSoltura

Жыл бұрын

Recorded with Reaper. :) I render voiceovers in: Mono, 24 bit, 48khz, 320kbps .MP3.

can you do a teardown video on that thing?

I got my um2 for $20 from sweetwater a couple of years ago so I guess there's no reason to ditch it for this.

@DaveSoltura

Жыл бұрын

What a steal! Absolutely no reason to ditch the UM2 for this.

Got this and I'm hearing that interference as well it's driving me nuts, I can only seem to fix it with noise reduction but then it muffles Mt audio too much. Guess it's time to return this

Any other cheap alternatives to pqir with the k688 that doesnt have problems like popping and static like this $29 one?

If like you said there is a bit of a distorted sound with this option would you recommend the option you are comparing it to more if price isn’t really an issue? Or are there any other contenders? I am looking for a decently priced (not 500$ goxlr) unit to upgrade to xlr for my streams I will be starting soon. I use the same exact dynamic mic you are using in this video. The reason I am switching is because I have to adjust too much in post for gain due to the gain through usb being so low.

@DaveSoltura

Жыл бұрын

Hi! If you really want quality, and money is not a concern, go for the Motu M2. You won't need a cloudlifter or additional sources of gain to power the mic with it. It won't have the audible interference, and it'll be futureproofed. For many people, that can very well be their last audio interface, until it needs to be replaced. Mine has served me well for more than 2 years now.

@TalonRahl

Жыл бұрын

@@DaveSoltura thank you for the recommendation! Adding it to the list to take a look at. Anything in the in between 100$ range where the m2 is the highest and the teyun q12 is the lowest? Based on quality.

@DaveSoltura

Жыл бұрын

@@TalonRahl The Behringer UMC202HD and 204HD should fit the bill. :) They’d be about half the cost of the Motu. Here’s my review and comparison: kzread.info/dash/bejne/iaJsrMx_p6-rZ9Y.html

@TalonRahl

Жыл бұрын

@@DaveSoltura watching and liking as we speak! Thank you for the assist!

@DaveSoltura

Жыл бұрын

@@TalonRahl Thank you for watching! Hope it helps!! Happy to know any future videos you might want to see, too!

Can I use this with a DAW for electric guitar, like Waveform 12?

Did you tweak the audio? because it sounds good like podcast 😊😊

@DaveSoltura

11 ай бұрын

Hi! Aside from normalizing the audio (boosting the volume) we didn't do anything else to process it. This is practically raw.

Phantom power won’t damage your dynamic mics.

@DaveSoltura

Жыл бұрын

They do sound worse though!😂

@JeffBourke

Жыл бұрын

@@DaveSoltura legit? I didn’t know that.

@Sanre

10 ай бұрын

@@DaveSolturait just means you don't have shielded xlrs

Good morning; is it possible to connect teyun q12 to a mixing console?

how about the sound latency for monitoring?

Can I ask a question? I am using Teyun Q12+K688+XLR to XLR cable too. But the volume of the microphone input is very, very low. The volume setting on the Windows Control Panel is already set to 100. But in Audacity the recording is only about -30dp~-20dp. And when I chatting with my friends on discord , they have a hard time hearing me because the microphone is so low. (My mouse is about 5cm close to k688.) How to solve this problem? Best regard.

@omba69

9 ай бұрын

What microphone are you using? If you are using condenser mic, you need to turn on the +48v phantom power

does it make a good combo with bm800?

Hearing audio pops on it

Can i just wrap it in aluminium foil to remove interference?

Can you monitor the pc sound to teyun without outputting it to the main?

Question, when you're recording with OBS with it, does the computer audio gets picked up by the mic? Because, my Audio Interface V8, when I try to hear my computer from it, it also gets outputted in my mic, how about this?

Hey, i bought this one but why is that when I record. There is this high pitched hiss? Help.

Can I record an unbalanced stereo keyboard audio output from my Korg pa 300 on this device? Also is it better than using an m audio track duo/solo audio interface for the same purpose?

@DaveSoltura

Жыл бұрын

Haven’t tried it myself, but you should be able to with the combo jacks. The m-tracks are known to have a bit if “jumpy gain” i.e at a certain point, a few degrees of turning the gain would boost the gain by a disproportionally big amount. The Teyun has a tiny bit of static. It’s now a matter of which drawback you’re willing to live with. 🙂

Is the video recorded using the k688 or that necklace thing?

@DaveSoltura

Жыл бұрын

The unboxing with the DJI mic (necklace thing), and the latter part uses the K688.

Hi, was wondering if you think, if the price didn't matter, would you get the teyun over the behringer? Im in the market to get my first audio interface to pair with a samson q2u was just wondering if you thought the extra price on the behringer would be worth it?

@DaveSoltura

Ай бұрын

Hi! I can't say I recommend the Behringer anymore as I had driver concerns the last time I tried to boot mine up. Not sure they're updating software to match OS updates. Right now, the Fifine SC1 is a significant jump from the Teyun, at around $54.99. But you can also find the Focusrite Vocaster One, or Presonus Revelator io24 interfaces at $99 (they both used to be $200). Those 2 interfaces are also a great step up from the Fifine SC1. I suggest going for either the SC1 or one of the above interfaces.

@oalkie

Ай бұрын

@@DaveSoltura thanks alot I appreciate the work you do.

@oalkie

Ай бұрын

@@DaveSoltura Hi, one more thing. Woudl the Fifine SC3 be comparible to the SC2?

@DaveSoltura

Ай бұрын

@@oalkie Yes, they’re about the same quality 🙂

gotta start puting affiliate links in your disc

yo i just bought this audio interface w/ my fifine k688 but when I use the xlr interface, the audio seems to be lower than when I use usb mode. i've set gain and the other red knob on max and i also ensured that its maxed out in the windows settings

@DaveSoltura

11 ай бұрын

Kindly check my pinned post!

For the price Is the killer dynamic microphone

@DaveSoltura

Жыл бұрын

Definitely is!

Hi, sorry for my stupid questions. I m planning to buy AT2020 then this Q-12. Anyone ever tried those together? (Also right now in my country AT2020XLR and this Q-12 is the same price as AT2020+USB, which could be better?) Just for beginner/intermediate singing and music production aka bedroom producer whose cheap USB condenser mic broke haha Thank you :D

@cecilsolidon2181

Жыл бұрын

Ff! Also planning to buy these two but still wondering if they work well together.

Greatings what is the cable xlr you connected ??

@DaveSoltura

7 ай бұрын

Just a generic xlr cable!

Can u use it with a two maono pd100 as a podcast set up

@DaveSoltura

3 ай бұрын

you can! but make sure to to clean up the static in post.

nice mic, can you use teyun for at 2020? and also this mic and at 2020 which one is good?

@DaveSoltura

Жыл бұрын

It as a 48v feature so yes it can power the AT2020. Both mics are great. AT2020 is proven to last you a decade of good use if well-maintained. K688 sounds great but I’m not sure about longevity. You get less reverb with the K688 and more bass with proper mic technique. Personally I’d choose the K688 if I started over :)

@inang1968

Жыл бұрын

Hi have you tried it together? if so - did you plug the AT2020 to the mic condesner 3.5mm plug or the XLR mic input 1 plug? Cause I watched a video saying AT2020 is a condenser mic. I literally just googled microphones today cause mine just broke. Thank you in advance :D

@DaveSoltura

Жыл бұрын

@@inang1968 Hi! I have not tried them together. But it’s best to plug the At2020 into the XLR input, as that’s what it’s designed for. Make sure you’re getting the XLR version of the At2020!

@DaveSoltura

Жыл бұрын

@@inang1968 here’s my video on the At2020 and its other versions: kzread.info/dash/bejne/YnZszKSsj8ivosY.html

@inang1968

Жыл бұрын

@@DaveSoltura Thank you thank you thank you!!!! :)

My teyun q12 has a weird hissing noise how can I fix that? And it isnt the microphone its the interface

Is it still cheaper than $20 now. The price point might have been raised quite a bit. Perhaps it's related to your review here. 😄

@DaveSoltura

Жыл бұрын

It’s still $29 via the affiliate link in the description! :)

@ntonyworkshop

Жыл бұрын

Thanks! I didn't pay attention to the video title. It does state the current price. Still the to-go budget interface. I have the Behringer UMC22, but need another interface on other equipment. Nice review!

@DaveSoltura

Жыл бұрын

@@ntonyworkshop The UMC22 is a great pick! Hope you enjoy the Teyun!🎉

Need a cloud lifter to get rid of that background sound

Do you think this mic and interface would work well on a M1 MacBook Air?

@DaveSoltura

Жыл бұрын

Definitely! You’d need a USB-C to USB-A adaptor, though.

@Joshisbrown

Жыл бұрын

@@DaveSoltura 🤝🤝

Is this applicable to smartphones?

i bought teyun q12 and it barely record my sm58 :/

What does the 1L-2R button do? As well as loopback

@DaveSoltura

5 ай бұрын

Switches between mono and stereo. Loopback uses your pc audio as part of the recording/mic input

Anyway to hook up a phone to it if I want to stream?

@DaveSoltura

Жыл бұрын

The K688 works with Android phones on USB-C. I have not tried connecting the Q12 to a phone.

Is it normal for the audio gain to weaken when I switch from USB to XLR using this Q12?

@hasanalnasser8899

Жыл бұрын

I'm also using k688

For electric guitar?does it do a really good job

@DaveSoltura

6 ай бұрын

Can’t say I’m the best judge for that, as I don’t have one!

Is it a good combo if i use it with maono pd100 ? Please 🙏

@DaveSoltura

9 ай бұрын

It'll work fine!

Is that compatible also for Phone? Like IPHONE

@Bud_GamingPh-zv5ml

Ай бұрын

The Q12

What will happened if turn on phantom power to dynamic xlr mic? Is it good or bad?

@DaveSoltura

11 ай бұрын

Won’t necessarily break it, but there could be some odd frequencies/sounds that are not supposed to be there.

can a smartphone power up teyun ?

Is this asio based?

Here in the Philippines, it's like $11.99 USD😃

@DaveSoltura

29 күн бұрын

It sure is!

I have q-24 and have no static at all

@DaveSoltura

Жыл бұрын

Thanks for sharing. Good to know!

In 1:20 you advised not to use a usb hub because of the popping noises, do you know how to fix that? I've been having that issue for a long time now.

@DaveSoltura

Жыл бұрын

Hi! Have you tried switching to a USB 3.0 cable? The provided cable is apparently lower than that, which is responsible for most of the pops and clicks. A new USB 3.0 cable should help minimize that.

@MaxKosaka002

Жыл бұрын

@@DaveSoltura Thanks for the fast reply! I’ll try that, thanks

@MaxKosaka002

Жыл бұрын

@@DaveSoltura I have another question, how am I able to make sure my mic isn't underpowered? Where else can i plug it besides the usb port?

@DaveSoltura

Жыл бұрын

@@MaxKosaka002 Hi! If you're using this mic + interface combo, your USB port is really the way to go. Or you could try using the USB 3.0 cable for the K688 without the interface. That's not underpowered in my experience.

Is it ok to use the fifine k688 on guitar recordings?

@DaveSoltura

Жыл бұрын

For acoustic guitar, it won't capture the higher end of frequencies and it can sound dull. It could be passable to do you, but I'd personally use a condenser mic instead.

Could you use the k688 with a XLR to jack cable ? A serious genuine question cuz I'm out of budget for a sound interface

@DaveSoltura

9 ай бұрын

I would not recommend doing that, as you would be using your computer’s soundcard and preamps. BUT! If you spend a little extra on a USB 3.0 cable instead, the quality you can get on the K688 in USB mode is incredible for the price.

@VincentN0ne1

9 ай бұрын

@@DaveSoltura thanks for responding kuya. I tried it and it actually sounded alright but Im using usb now and also for some reason my k688 is hella diff from what you have. the capsule of it isnt actually touching so its more like a shure sm7b where there is space between the capsule and the metal.

@DaveSoltura

9 ай бұрын

@@VincentN0ne1 Try getting your mouth much closer. Like 3 inches away from the capsule. :)

@DaveSoltura

9 ай бұрын

Actually, even an inch!

@VincentN0ne1

9 ай бұрын

@@DaveSoltura Ive been using it with steelseries sonar with 50% gain on it and it actually picks up okay with even an arms length away but it does sound alot more muffly so ill try with an inch to 3 inches away

why is there low quality electric cable sound on the background?

@DaveSoltura

Жыл бұрын

I did mention that! It's definitely a drawback for an interface at this price, but good mic placement can help attenuate it.

Would this work for music production?

@DaveSoltura

Жыл бұрын

It can work as a basic combo if you have music production skills.

Honestly just go with the fifine sc3

I always get distorted sound with my condenser microphone when I get really close, even when I’m only getting -12db in Logic Pro, is this a problem or should I just stop touching the mic when I sing

@DaveSoltura

Жыл бұрын

Hi! What do you mean by, you’re “touching” the mic? And what condenser mic is this?

@bf4lvr

Жыл бұрын

@@DaveSoltura touching as in im so close that my lips are making contact with the mic, and it’s one of those really cheap Chinese mics so that might be why, im not even sure what the name is

@DaveSoltura

Жыл бұрын

@@bf4lvr Yes, it's completely possible getting that close is introducing extra distortion alongside proximity effect. I'd recommend stepping back maybe 3-6 inches and see how that impacts sound.

Shouldn’t that main knob be like a master volume and only set at 3 o clock max, anyhigher would definitely start popping sounds…i would set main to 3 oclock and leave it there…and adjust only the levels of the mic line and other inputs.

@DaveSoltura

Жыл бұрын

That's valid!

@benjiebarker

Жыл бұрын

@@DaveSoltura is it possible to connect straight to ipad pro that has usb-c…could the mic/pc switch allow you to play youtube karaoke videos and record while you sing?

@DaveSoltura

Жыл бұрын

@@benjiebarker I’ll order a usb b to usb c cable and try it out. I’ll let you know!🙂

Is the Q12 better that the M Track Solo?

@DaveSoltura

2 ай бұрын

Not at all. The M Track Solo is solid! Just pricier.

@alfredg.m

2 ай бұрын

@@DaveSoltura Thx for the answer. Btw wondering if adding the M Track Solo would make an impact on the K688. Cause I heard the K688's internals are pretty good

@DaveSoltura

2 ай бұрын

@@alfredg.m It's possible, but I can't say for sure. Any difference could be negligible. A true upgrade from.the K688's preamps would warrant something like a Motu M2 or SSL2 as an interface.

what does the "ST PAN" switch do?

@DaveSoltura

Жыл бұрын

I recorded a short about that! kzread.infoW5ZH69P6_js

would you recommend this mic to someone who wants to make covers? (singing)

@DaveSoltura

5 ай бұрын

It might seem dull for that application, but it does the job. Consider the Fifine AM8 instead: kzread.info/dash/bejne/X2153MexqpSvdaQ.htmlsi=kpFwshst7ApO22tO

@JasYTC

5 ай бұрын

@@DaveSoltura thanks! but I'm looking for a mic with XLR 🥹 would you recommend one around the same price range or maybe lower?

@DaveSoltura

5 ай бұрын

@@JasYTC the AM8 has xlr compatibility! Or do you mean with a cable in the box?

@JasYTC

5 ай бұрын

@@DaveSoltura yeah that's what I meant hahaha thoughts on the fifine k726?

@DaveSoltura

5 ай бұрын

@@JasYTC I don’t have it yet. It looks promising, but I’ll have to hear it myself before I jump to any conclusions :)

The combo totally sucks. Super bad noise no matter what I do. You can check my latest videos compared with the older ones with the Audio technica mic.

@DaveSoltura

Жыл бұрын

Hello! Thanks for taking the time to leave a comment on this channel. I had a look at your videos and compared them. You can dramatically improve the K688's signal-to-noise ratio/noise performance, by getting very close to the mic itself. An article on Sweetwater states, "each time you double the distance between your sound source and a listener or microphone, the power of the audio drops by 75% - a fairly significant amount! " (See www.sweetwater.com/insync/inverse-square-law/) So once your mouth is much closer to the mic, this boosts the overall volume by a lot... which means when you normalize your audio, the static would be significantly weaker, and can easily be wiped clean using simple noise reduction. The solution isn't perfect, but it's still an incredible value for the price. Feel free to check out my other video on mic technique, so your audio volume can sound loud, and your background noise will be much quieter: kzread.info/dash/bejne/o3Vmyqlrm5bMYrA.html

I wonder if it works great on instruments.. 🤔

@DaveSoltura

Жыл бұрын

If you mean the interface, maybe not great, but good enough for starters!

can i listen to my silf with no delay with this interface?

@DaveSoltura

Жыл бұрын

Yes you can!

Does this work with Mac's as well?

@DaveSoltura

5 ай бұрын

Yes!

Can you compare sound of them?

@DaveSoltura

Жыл бұрын

Hi! Which ones exactly?

@blackjohnny0

Жыл бұрын

@@DaveSoltura I probably thought abour Teyun and Behringer.

Teyun Q12 work DT-700 250 or 80 ohm?

@DaveSoltura

Жыл бұрын

It would work on the 80 ohm with more volume. :) On the 250 ohm, it's still fairly audible-- I wouldn't call it faint, I wouldn't call it loud, either. Personally, I'd say it's usable for monitoring, but it would be a stretch for mixing.

@seifallahdirgham3206

Жыл бұрын

@@DaveSoltura thank you

The interface has one major issue. There is a periodic click/pop sound that totally destroys the audio

@DaveSoltura

Жыл бұрын

Thank you for calling attention to this.

we can hear the pops from now and then, and the preamps seems very none existing.

@kamratdennis

Жыл бұрын

im not shure about the pops , it might be youtube.

@DaveSoltura

Жыл бұрын

Yes there are definitely pops in USB mode if we use the cable that comes with it. Needs a USB 3.0 cable for pops to disappear. :)

@genetalavera4256

Жыл бұрын

Yup can hear the pops as well using the xlr connection.

BROO AN INTERFACE I CAN AFFORD!!!

I bought this to have an audio interface at my girlfriend’s place

ung live monitoring nito walang latency or delay?

@DaveSoltura

Жыл бұрын

Not in my experience. Live as can be. :)