267whp 8th Gen Civic Si! Fully built & gutted
Ойындар
K20a2 head, drag cartel 4.5 cams, supertech valvetrain with steel retainers Ferrea 6000 valves
K24 block, k1 rods, wiseco 12.5:1 pistons, ported type s pump.
Skunk2 centre feed, skunk 2 header, skunk 2 3 inch exhaust, j37 throttle body, 3.5 inch intake
Skunk2 centre feed, skunk 2 header, skunk 2 3 inch exhaust, j37 throttle body, 3.5 inch intake
Id1000 injectors and a dw200 fuel pump
267whp 192tq
Tuned by chase_on_tuning !!
Пікірлер: 28
People that own a si knows that 5:50 sounds crazy cause short shifting and still being in power band spinning like that is insane in commenting a lot but I love this build
Good God this thing is spicy can't wait to see what chaseontuning can do to this beast next year wake it up even more 300hp n/a would be crazy
definitely retune, leaving a lot of power on the table.
@clintonsmeenk1022
7 ай бұрын
That’s the plan dude. We didn’t touch timing 267 was on super conservative timing
This cars an absolute animal
god that idle is so good
I love this thing I have a tip for you too so you can save that transmission of yours with that much power too
Love the song choice 😂🤣 party animals lol
God bros this things move !!!!! 😈😍🤟
that intake is cracking me up lol
🔥🔥
Holy sheeeit
any guesses on what it will do 60-130mph or 1/4mi. gotta get a dragy and do some runs
Not hating but with the amount of stuff you’ve done to the engine I thought you would be running more horsepower than that . I’m running a K24a Rbb3 Makes 253hp 192tq Skunk2intake manifold Skunk2 3 inch exhaust 550cc injectors 74mm throttle body Cheap air intake 3 inch Skunk2 Alpha headers Type s oil pump Acuity short shifter Carlos tuned on hondata
@SofaKingNYce
7 ай бұрын
I thought he would be making more too
@clintonsmeenk1022
7 ай бұрын
Car didn’t have timing touched at all, that 267 was strictly on vtc and fuel being straightened out. My flywheel ended up coming loose so obviously we stopped. Didn’t get back there to finish it yet.
@Motofried
7 ай бұрын
@@clintonsmeenk1022that makes sense . You should throw some e85 at it in the future I bet it would be making really close to 300 .
How are you using a shifter box? What cables are you using and what else did you have to change ?
Do you know your 60-130mph time ?? Just curious since I want to build my si as well
💀 was that the cold air intake popping outside the bumper look like a stoggy
What throttle body are you running and is there any modification to get the center feed to work in a 8th gen si
@Hunchosburnouts
7 ай бұрын
Just need to cut water pump and get half rad and that should roughly be it
@backyardracin
7 ай бұрын
@@Hunchosburnouts is there a certain throttle body you have to use and what about the wire harness does it reach far enough
@clintonsmeenk1022
7 ай бұрын
@@backyardracin used a j37 with an adapter. Also had to extend the throttle body plug
What’s your exhaust setup ?
@Hunchosburnouts
7 ай бұрын
skunk 2 header, skunk 2 3 inch exhaust, build list in description
Stock trans?
@Hunchosburnouts
2 ай бұрын
Yup