Had same problem with same Carli track bar as part of their leveling kit. Instructions on how to measure distance between eyelets is pretty vague, but you can get it to center your axle by shortening overall length by screwing eyelet in (cw). Problem is that you’ll need to unbolt eyelet end to do so, and it’s a guessing game how many turns in you’ll need to go, so a few iterations.

@mcmahansgarage

Жыл бұрын

Yeah not to mention having to re torque the jam nut.

@mrfuninthesun33

Жыл бұрын

Bros the Carli instructions for their track bar are super clear. Gives u the length u need to make the track bar with the corresponding lift kit height. I measured twice and installed once. Done and centered and no more death wobble

Good morning the problem is that if you put a 2 /1/2 leveling kit you should buy the trackbar bracket with the the same 2/1/2 inches dropped

@mcmahansgarage

Жыл бұрын

Roger

I would advise putting a tack weld On both sides of that nut.. Otherwise it will eventually start turning back and forth at the thread.. Of course It will not be able Really go anywhere. So as the truck bounces up and down it will turn/move between the 2 halfs of the track bar at the adjustment thread instead of at the ball joint.. Eventually causing wear to the threads... ... You get it where you want it.. Buzz a couple small tack welds.. Make weld small enough so You can easily remove it with a grinder& cutting wheel.. 🙉🙈🙊👤

@mcmahansgarage

6 ай бұрын

I just safety wired it and called it good

Do you have a video reviewing the Carli Level Kit you installed? I couldn’t find one. If not, how’d you like it? Big difference? How was it before and after the install off the add-a-pack? I’m thinking about getting a carli kit for my 2014 f350 and need to figure out if I need all the extras or if the kit by itself will be good. Was thinking either the commuter or the backcountry kit. Would love to know what your thoughts are!

@mcmahansgarage

Жыл бұрын

Personally i think upgrading is a waste. Yes the ride quality is minimally better but if youre like me and your truck only sees off road trails on the weekend to hual a dirt bike somewhere then its not worth it to purchase resivors. Yes i will give it to carli you can feel a difference, but a $4,000 difference? I dont think so. The basic kit will do the trick

If you turn the top bolt, the pitman arm hits it at full lock left I believe. Someone may have already commented that. Didn’t read all comments

@mcmahansgarage

6 ай бұрын

Thank you for the input friend

Is it possible to install this incorrectly? Which direction is the bend in the track bar supposed to be? Toward the front or rear. I have the full kit on my F350 and hear clicking turning wheels fully right or left and I’m also a 1/2” off center for the axle. Need to fix this!

@mcmahansgarage

Жыл бұрын

No you should be able to install backwards. If you have the adjustable track it's pretty easy to readjust the length to center that axel though.

I thought I was going crazy until I saw this video and read the comments. I measured the Carli track bar four fricken times and after install I was off the same amount as you. It sounds like this must be normal and I should just leave it alone instead of fighting it.

@mcmahansgarage

Жыл бұрын

Yeah it's just a pain in the ass I'd leave it

I had the ready lift 2.5 with bracket on my 19 250 with 35x12.5x20 and it was centered. Replaced with Carli springs and Fox shocks and added Carli shims to correct caster. Drives much, much better and tracks straight, but now the axle is off to the right .5 inch. The truck sits only slightly higher so how did I get off to the right?? Shouldn't higher pull the axle to the left?? So now I'm rubbing on right tire front when I turn to right and go uphill. Thinking about going back to stock bracket and getting an adjustable track bar. Main question... couldn't you remove the bar, jack the truck, center the axle, drop it, and then adjust the bar length? Thanks for the vid!

@mcmahansgarage

Жыл бұрын

Theoretically I'd say yes but kind of seem like a pain in the ass. However, if you do in fact try this let me know how it works.

@MACKROV

Жыл бұрын

@@mcmahansgarageLol. That why I'm an accountant and not a mechanic. Guess it would be a pain unless I could lift it from somewhere other than the axle itself and/or I got it perfectly right the first time. We both know the latter isn't going to happen. I'll let you know, but there's a reason 2 hour jobs take me a day. 🤣

@mcmahansgarage

Жыл бұрын

@MACKROV yeah I vote to just deal with it lol

@codyhenry3926

6 ай бұрын

You need an adjustable track bar..

would it be possible the track bar is backwards? my adjustable on 2020 the gussets welded to the eye is the bottom(passenger side) with a ball joint and him joint is top side (driver). just a thought, as i have not installed mine yet and no idea of the brand on mine.

@mcmahansgarage

3 ай бұрын

No it only goes on one way.

I called cjc yesterday and they advised me that on the leveling configuration in order to have proper articulation, they have the measurement on that track bar set that way on purpose. I know it’s annoying. I really thought about getting a pmf trackbar but I’m going to leave it alone. I love carli parts but this one didn’t really make sense to me at first either. Both me and my dads trucks have the same trac bar and have had the same result. Hope this helps.

@mcmahansgarage

Жыл бұрын

Yeah I'm just going to leave it 1/4 off isn't that bad

@burnair1608

Жыл бұрын

I like the baja tractionater better costly but best of all worlds in correcting the wobble problem!

What did you end up.doing with both the axle and steering wheel?

@mcmahansgarage

Жыл бұрын

I adjusted the steering to straighten the wheel

Can ya put it on first before torquing it, center up the axle, then torque it?

@mcmahansgarage

6 ай бұрын

No because you wouldn’t be able to turn the Heim joint

No need to be aligned....just adjust the steering linkage and replace your steering wheel straight......and for the track bar if is just one quarter of inch difference on one side its ok........even on stock form the front axle isn't centered!!!!

@mcmahansgarage

Жыл бұрын

Thank you so much

That steering wheel twist is super easy to fix.

@mcmahansgarage

Жыл бұрын

Yeah I got it figured out thanks friend.

Did you ever figure out a fix for the axel being to one side ?

@mcmahansgarage

Жыл бұрын

Adjustment on the track bar was a little off.

@maxschlum8898

Жыл бұрын

@@mcmahansgarage did you measure from center of bolthole to center of bolthole on both ends? I’m doing the same track bar soon on my truck

@mcmahansgarage

Жыл бұрын

@maxschlum8898 yes I did

Nice video, do you plan to upgrade your headlights? I want to upgrade mine and want to find a how to video. BTW, can I find you on IG? Thanks😉

@mcmahansgarage

Жыл бұрын

I like these headlights so probably not and yes IG is mcmahans garage

Enjoy your vids and I mean no offense but with all the mods you have done., why didn't you just by a Tremor?

@mcmahansgarage

Жыл бұрын

Because the tremor is overpriced and rides like shit. At least spending money on aftermarket suspension makes it ride better

@kevinA1973

6 ай бұрын

exactly, for tremor package buy a carli kit and a tremor sticker and still saves money and rides better @@mcmahansgarage

It is a lot easier to use a bottle Jack to push the track ball joint out.. I mean, I like beating on s*** with a hammer just as much as the next guy but. Up under there It can be a pain in the ass to hammer on. . And you won't bugger up ur threads Or your fingers or anything else...👤

@mcmahansgarage

6 ай бұрын

Thanks

You have to actually screw it in and out.. Try screwing it out a little ways..... Yes i'm a mechanic.. That's a rough measurement they gave you.. It will get you close.. It's not set in stone.. Move it where it needs to be.. 🙉🙈🙊👤

@mcmahansgarage

6 ай бұрын

Thanks mechanic

【ｐｒｏｍｏｓｍ】