Watched 4 videos on KZread, this was by far the best and most comprehensive. Thank you.

@canamsledder

7 ай бұрын

Thank you!

Thank you for showing that the brake pads changed .

Hey I used your video to guide me change my rear disc pads. I really appreciate your video. Helped me save some money. I didn’t have to change the front since it was worn down just a bit. Only the side with the wear sensor in the rear was worn down. One pad, due to the spring piece breaking off. I had no errors after but I have to replace my wear sensor since it was broken.

@canamsledder

4 ай бұрын

The pads do not seem to wear evenly, that's for sure.

Excellent Video

Excellent video man. Subscribed!

@canamsledder

11 ай бұрын

Much appreciated!

I appreciate you, sir

Hey Great Video Eh? Very Helpful and I love hearing your Canadian Accent. Is it ever excellent eh? Clicked the thumbs up and subscribed for future videos. Cheer's!

I usually get codes out the wazoo doing front pads. Even in brake service mode. I've been told you have to do some MOJO with a code scanner but mine won't do it. It's only good up to 2018 and they haven't had any updates. The other one I just don't have regular access to. What I have found is that speed is limited to 43 mph then go 43 mph for a bit, safely, then park it for a bit. Around 5-10 min or so. When you start it back up the codes usually clear.

@justingarza6316

8 ай бұрын

If they engine light and ESC Light is on just go to Orileys they'll clear the code then good to go it's free😊

Great video. Appreciate the in depth info in it. Unfortunately though for me when i took it out of brake service mode all the systems failed and got limited to 43mph. Going to take to dealership to get them to reset it all and hope it cleans it all up.

@canamsledder

7 ай бұрын

I've heard that before. Drive it a couple of times, let it cycle through and it might clear on its own. Let us know how you make out.

@niq872

4 ай бұрын

I saw someone that had that problem they were a le to fix it by pressing the brakes and holding down the power button 30 seconds

Dude I think the metal sensor on the brake pad goes up not down check the schematics from the Chevy dealer they'll print it out for you, your video was still helpful

@canamsledder

2 ай бұрын

They will only go one way.

mine did not do that so now I got a service park brake

Question will this be the same on 2021 Silverado?

Will this work on a 2019 GMC sierra

Great video ! Getting ready to do the pads on 19’ Z . Was wondering how many replacement sensors I need to buy since Rock automotive pads don’t come with sensors , thanks .

@canamsledder

4 ай бұрын

Let us know how you make out.

@frankjerseytomato8941

4 ай бұрын

you need one its only on the left rear i dont know about the front

Did you have to open the brake reservoir cap to push the calipers in on the front pads

@canamsledder

9 ай бұрын

No, I did not have to. Just check to make sure there is room for the fluid to be pushed back into the reservoir.

Nice video! Any issues not replacing the front rotors and only the pads? I am at 62K miles and at like 20% on the sensor, visually they match this and are worn pretty good. Debating just changing out pads vs pads and rotors.

@canamsledder

Ай бұрын

Nope, no issue.

Would you happen to know the torque specs for the callipers 14 mm bolts in the back. I plan on doing the rotors as well. Very nice detailed video.

@canamsledder

11 ай бұрын

Front caliper slide bolts, 74 ft-lbs. Front caliper mounting bolts, 170 ft-lbs. Rear caliper slide bolts, 38 ft-lbs. Rear caliper mounting bolts, 148 ft-lbs. At least that's what I find online.

@ricflores1369

11 ай бұрын

@@canamsledder Awesome Thank you!!

@canamsledder

11 ай бұрын

@@ricflores1369 and don't forget the loctight

@jesseleach3883

11 ай бұрын

​@@canamsledderholy crap is that really the specs cause that's a tight ass bolt then

@jesseleach3883

11 ай бұрын

Most lugnuts aren't over 100 ft lbs

How do you return from brake pads maintenance mode ? After you have replaced everything ?

@ChrisM-gj2uc

5 ай бұрын

Watch the last minute of the video. I explained it. Thanks for watching.

Did you pump the brakes after replacing the pads afterwards to seat them. I’ve heard it may not feel like traditional ones where they will firm up because of the new electronic parking system. Just wondering what you experienced

@canamsledder

4 ай бұрын

They pumped up like normal.

@Zebraunit22

4 ай бұрын

Are you saying that with the engine off you pumped the brakes till they felt firm?

@canamsledder

4 ай бұрын

With the engine running.

when put in service mode it automatically winds caliper in on rear so you don't need to press in manually.

@canamsledder

7 ай бұрын

No. It for the electric parking brake.

Add any lock tight to any bolts

@canamsledder

5 ай бұрын

If there is lock tight on from the factory, I clean off and re-apply. The caliper bracket mounting bolts always have lock tight on them.

So after you do the electronic brake service, the piston pushes in, not spun in

@canamsledder

11 ай бұрын

Correct. Just pushes in.

No lube on the clips where the ears of the pads sit?

@canamsledder

10 ай бұрын

The clips are stainless, so not really necessary. But it won't hurt if you want to.

Anyone have a service system for brake pad wear life indicator on.. ive tried 2 new different pad sensors still get the red message. Do i have to cailnrate or something?

@canamsledder

9 ай бұрын

When I put the new pads and indicators on, it came up on the dash, something like new pads detected, press to confirm. Or something like that.

@Squalevision

9 ай бұрын

@@canamsledder thanks . Mine is just stuck saying service system and can't reset it

Great video other than the “C-clamp” part. Should you need to retract the piston , the C clamp method will not work with the 2019+ caliper design. They have a threaded piston so a spinning type clamp must be used. With that said, If put into service mode it isn’t necessary as the piston should retract close to 100%.

@canamsledder

2 ай бұрын

Service mode only retracts the parking brake. The pistons on this truck pushed in straight.

@ajsfree

2 ай бұрын

Interesting. With my ‘20 Sierra at4, I had to grab a caliper threaded kit to screw the piston back in to allow enough space for pads. However, there is a possibility that this happens if the piston extends too far as I didn’t have an issue needing to retract as far when doing the opposite side.

How did you reset the brake life on the dash?

@canamsledder

Жыл бұрын

It reset automatically. It came up on the info center "detected new pads, press yes to confirm" or something similar.

Did you disconnect the battery before changing the pads? Did any codes pop up afterwards?

@canamsledder

Жыл бұрын

No I did not disconnect the battery. And no codes.

@sodbuster518able

11 ай бұрын

I thought rear caliper piston had to be rotated while pushing back and also very important slots only align up with pad in a 6 and 12 o'clock position

@sodbuster518able

11 ай бұрын

What kinda mileage life getting out of these pads? I would expect 100k miles or greater before this service required?

@canamsledder

11 ай бұрын

@@sodbuster518able Only 37,000 mile. Pad wear was not even.

@canamsledder

11 ай бұрын

@@sodbuster518able I thought so too, but nope.

What do you do when you don't have a parking brake button

@canamsledder

5 ай бұрын

Then I guess you don't have the electric parking brake. What year is your truck?

My 2019, 39,200 miles. Same wear pattern,

@canamsledder

11 ай бұрын

It must be the design of the calipers.

@757MrMark

11 ай бұрын

@@canamsledder 1st time I worked on calipers that did pucks on both sides.

Should break service mode be turned on if I'm only doing front brakes ? Please explain, I'd greatly appreciate it. I don't wanna mess anything up.

@canamsledder

4 ай бұрын

I don't believe so. It's only to release the electric parking brake.

@Bmills893

4 ай бұрын

@@canamsledder THANK YOU GREAT VIDEO BTW !!

@Bmills893

4 ай бұрын

Hello it's me again I followed all the steps in this video and after I started my truck I had all the codes come up. The same ones mentioned in other comments on this video. I drove it around the block got to 43 mph twice and took it home. Parked it for around 10 to 15 mins started it again and all codes were gone except the engine light. Turned it off again and waited around the same amount of time and it also went away I have now driven the truck about an hour round trip to work and back for the day. However I am home now and still nothing I can't get the front brake life percentage to reset. Cannot find a way to resolve.... any ideas??????

@canamsledder

4 ай бұрын

@brianmills5613 for me, it came up on the info center. Said new pads detected, press to confirm. Something like that.

@canamsledder

4 ай бұрын

Question Brian, did you move the truck with it in brake service mode?

so how would one do this with a c clamp

@canamsledder

9 ай бұрын

Same as any of the older vehicles you've worked on. Just put the old pad against the piston and use the C clamp to push it in.

@Titian92

8 ай бұрын

@@canamsledder You can't use a c-clamp on the rear piston because they are threaded in. You will be replacing the caliper if you do.

Do you need to leave the ignition on the whole time?

@canamsledder

3 ай бұрын

I did not.

@chriso5974

3 ай бұрын

Do you need to do service brake mode for the front pads too? Or just the rear

@canamsledder

3 ай бұрын

Just the rear, to release the electronic parking brake.

Can you do that with a 2019 chevy traverse?

@canamsledder

Жыл бұрын

My guess is they would be the same.

@dfi1026

Жыл бұрын

Great video... I'm doing my brakes soon... and this video will help. Question though.... you didn't change the rotors, how did you know they were still good? My truck has 55000 miles, would they still be good. Break wear is 59% front, and 43% in the back. I plan on going on a coast to coast road trip towing a trailer, so I want to be safe and just replace.

@canamsledder

Жыл бұрын

@dfi1026 If the rotors looks good, not all rusty and the truck stops without vibration in the pedal ( warped rotors) they should be good. Around here they get very rusty.

@sscamaro6832712

Жыл бұрын

Were you able to reset the brake life percentage for the front and rear without a scan tool?

@canamsledder

Жыл бұрын

@@sscamaro6832712 yes!

Made in China even says so in Mexican language for us. 😂

at least i can understand what you are saying. not with some third world accent

Will this work on a 2019 GMC sierra

@canamsledder

5 ай бұрын

As far as I know, should be the same.

@user-py5dz8wl6g

5 ай бұрын

@@canamsledder one last question did you disconnect your batteries?

@canamsledder

5 ай бұрын

I did not.

@user-py5dz8wl6g

5 ай бұрын

@@canamsledder thank you so much

@canamsledder

5 ай бұрын

Let us know how you make out.