2010 Chevrolet Malibu Start up issue Ignition key cyclinder replacement
A tutorial to guide you through replacing your Chevrolet Malibu ignition cylinder. The vehicle I am working on is a 2010, but this will most like be the same method for models close in year to 2010.
The vehicle has been causing trouble with starting up at random instances. It seems like it has a mind of it's own. After replacing the cylinder, the vehicle did cause the same issue once again. The temperatures are really low so I will wait it out to see if the cold is causing the problem which is likely since the days I have encountered the problem were the coldest days here in Saskatoon (-40 degrees).
Пікірлер: 29
Thank you so much for the detailed explanation. The dealership wanted $400+ to swap this out. They were quoting this as a 2.5 hour task.
Great video. Will be using this video to replace my cars cylinder. Will update with how it goes. Hah
Great video! thanks! Liked.
Thank you! I needed this info a lot my security light turns on while driving. Need to replace this.
@EngineerShah01
8 жыл бұрын
Your welcome. I also suggest watching my other video for the same vehicle. The cylinder replacement didn't fix my no start problem.
@reyesjose214
2 жыл бұрын
@@EngineerShah01 whats the part#???
Ever figure out what happened to the ignition switch video?
Thank you so much !!!
@EngineerShah01
5 жыл бұрын
Your welcome!
The key is stuck in my 2008 Chevy Malibu is there a release button somewhere please help
Chevy's Malibu 2010 won't pass emissions code p0701 and others any help
Thank you for this video. I had a problem where I could not turn the key all the way to the off position so the accessories would not shut off and the battery would drain. I bought a new key cylinder and that didn't fix it so I bought a new ignition switch and that didn't fix it either. It turned out to be the Chevrolet Malibu Shift Interlock Solenoid. I replaced that and everything worked again. it was a 2003 car with over 200,000 miles.
@josholivarez3804
2 жыл бұрын
after reading your comment halfway through I realized it had to be the shifter because I can't tell you how many times I've tried to turn off the car without it being in park lol hahaha
@leel2skummy
2 жыл бұрын
@@josholivarez3804 yoooooooo chillll 😂🤣🤣🤣 that’s probably whats going on wit my car its goin into power reduced mode i think its my ignition switch i tried to turn off my car plenty of times without it being in park😂
How can you tell if the cylinder is bad
How do you remove the thing you put the pins with from the cylinder
@EngineerShah01
6 жыл бұрын
Greg Deachan there is a small round hole at the top and you have to stick a needle in there and push down the ball that is holding it in.
@gregdeachan7117
6 жыл бұрын
Engineer Shah okay i tried that earlier and the ball popped out and the pin stayed in
You need to state that you don't have to reprogram the key if your relying the original key.
My N-Word !!!
Check
I couldn't find the cylinder fix
@ronnorman7862
5 жыл бұрын
Angel T. there's no cylinder. just a switch.
Can the same key be used
@EngineerShah01
6 жыл бұрын
ivan ibanez yes it can.
@claidheamdanns
3 жыл бұрын
Thanks! The keys on mine are brand new (a couple months old) from the dealership. So, I’ll go ahead and use the existing keys.
Ignition switch when turn it does not spring back
PLEASE! EDIT this Video because of "TMI"... thanks! (Yes as in Too MUCH Information)... GOOD material... it just takes TOO much time to get to each step).
@claidheamdanns
3 жыл бұрын
This is NOT too much information. Not everyone has the same skill level. I am not mechanically inclined myself, so I appreciate all the extra details.