2008 Mazda 5 Minivan Build| lower ball joint/ control arm replacement| Part 3

2008 Mazda 5 Minivan Build......
Music: Paradise
Musician: IMMNNC
URL: icons8.com/music
Music: Don't Stop
Musician: Jason Shaw
URL: audionautix.com

Пікірлер: 16

  • @dennisrodriguez9420
    @dennisrodriguez9420Күн бұрын

    Thanks for the video! Other guys removed the engine mount to remove the long bolt but you didn't. You save me alot of time. Great job bud!

  • @AndyFalvai-hh7ob
    @AndyFalvai-hh7obАй бұрын

    Very useful video! Saved me a lot of trouble on changing the lower control arm on my Mazda 5. Jacking up the engine is brilliant. Saved my day. Thanks, man!

  • @williamcamacho7214
    @williamcamacho72149 ай бұрын

    tanks bro!!

  • @luismedina2341
    @luismedina2341 Жыл бұрын

    Buen travajo😮😊

  • @mikoloe
    @mikoloe Жыл бұрын

    I had a clunkity klunk issue so I bought a set of control arms. I had the car up, tires off and was ready to change them out when I saw that there were 2 bolts loose on one side and 1 on the other. Just a quick tightening and I would have been done with it all. Since I was half way there and beside me were 2 new Beck Arnley control arms, it was a no brainer. Well, the rest is history and they perform like a champ. Moral of the story is, check for loose bolts before you spend money replacing something that knocks and Klunks.

  • @barbaralavoie2642
    @barbaralavoie2642 Жыл бұрын

    Thank you. Awesome job BTW! 👏

  • @tigersnake72
    @tigersnake72 Жыл бұрын

    Nice job

  • @realsacerdocionacionsanta6513
    @realsacerdocionacionsanta65132 жыл бұрын

    Thank you so much

  • @Segoviano74
    @Segoviano742 жыл бұрын

    Bendiciones bien explicado y suscrito

  • @jeffnapolitano3749
    @jeffnapolitano37492 жыл бұрын

    Thank you for this! Just wondering, though - did you torque the bolts upon installation? Looks like you used an impact driver to drive them in.

  • @Mangandi17
    @Mangandi17 Жыл бұрын

    Yo lo ise igual que el pero me quedo un problema el volante me quedo media vuelta ala izquierda

  • @plumslikerocks5538
    @plumslikerocks55383 жыл бұрын

    Hi - great video. I noticed that you referred to that chunky cylinder of metal on the arm as a bump stop. I’m interested in checking if that’s really what it is, because mine corroded and fell off! I thought bump stops were usually made of rubber and prevented bottoming out - I can’t work out what these would bump off! Any ideas?

  • @timkudryavtsev4133

    @timkudryavtsev4133

    2 жыл бұрын

    These are called dynamic dampers made of rubber. It is not a bump stop.

  • @DUNELIZARd7

    @DUNELIZARd7

    Жыл бұрын

    Same on mine 🤣 Owell rocking it thou

  • @jsol2480
    @jsol24802 жыл бұрын

    How did you install the 19 mm back? The one beside ac compressor

  • @BilutzZaA

    @BilutzZaA

    2 жыл бұрын

    Hello there ! In the manual it specifies that you must take out the screw of the lower engine mount, push the engine in front and then you remove the screw. To put it back in you do the same thing but in reverse. There are a couple of videos on youtube about that. Search for mazda 3 bk.