You can get it out without disconnecting anything on the intake side. Just take out the intake bolts, the two vacuum hoses and use a strap to hold it back

@ujudoka8928

2 жыл бұрын

Make the video and send it to me bro. I’m not trying to do all this extra stuff.

@NPCArchivist

2 жыл бұрын

@@ujudoka8928 lmao facts

@ipassbirdflu

2 жыл бұрын

Make that video yet? I’m at the regal replacing my shit son.

@XXLGUNZ619

2 жыл бұрын

love to see this video lol has it been made?

Don't forget to disconnect the Neg battery terminal

@PalomboDylan

3 жыл бұрын

i was about to ask this. thanks for posting this comment mate

@Airmanmx1

3 жыл бұрын

@@PalomboDylan no problem! Any time you deal with electrical anything it is important to disconnect the power source, obviously unless you need power to diagnose the concern.

Ty bro u saved me alot of headaches.

Thanks for a great video. You cut my time down to about an hour and a half.

@YoDIYVideos

2 жыл бұрын

Nice that’s a quick job!

That was pretty damn good,thanks

Thank you so much!!

Intake manifold definitely gotta come out for ease of replacement

Would you happen to have a a list of exact tools and socket sizes need for the whole job

@YoDIYVideos

3 жыл бұрын

I don’t have an exact set, but a standard set of metric wrenches or a socket set will be a great start. I’d get yourself a breaker bar, a set of needle nose pliers, and that’ll be a good start. If you have the funds, get a torque wrench too.

I am getting code problems with misfires and a Honda mechanic says it's because of the aftermarket starter. A Honda starter solves the misfire problems. I already replaced the Crankshaft Sensor and it did not help.

@YoDIYVideos

3 жыл бұрын

Had the same issues, wish I would gone original OEM. I heard getting the updates to the computer software helps

@YoDIYVideos

3 жыл бұрын

With that being said, I generally don’t let my starter crank if it doesn’t start. I’ll let it sit and try again, it’s a pain but I won’t swap another until this one dies

@jsinister_vq8303

Жыл бұрын

Damn, I just had my starter replaced OEM by the dealer because I was having the exact same issues and it solved all the problems.

@danielquaternik22

Жыл бұрын

@@jsinister_vq8303 You did the right thing. I replaced my OEM with an aftermarket and after a few months, crankshaft pos. sensor went bad. ( threw codes ) I've since learned you need to replace starter with OEM to avoid this. Just my experience and I'm in the process of changing back to an OEM starter and CPS. Don't know if I have to have the sensor "relearned". Waste of time and money.

When taking out that 14 and 17mm starter bolt , which you pushing the ratchet to loosen up the bolts ? Pulling it towards or pushing towards the car ?

@YoDIYVideos

5 жыл бұрын

You push the wrench towards the bolt and go counterclockwise. The bolt will naturally go out and loosen up. Once you place the socket on the bolt, then you let the wrench do the job.

@oshenandlily

2 жыл бұрын

Lefty loosy

Great video sir 👍👍👍

@YoDIYVideos

Жыл бұрын

Keep watching!

would it be easyer to get to from underneath?

@Airmanmx1

4 жыл бұрын

Not easier, it will cost less if you go from underneath to avoid discounting the air intake manifold and the throttle body gasket. No need to do the coolant lines on the throttle body either. So I'm short, save about $70 if you do the underbelly path

@ram43x80

3 жыл бұрын

How r u saving money doing it from underneath?

@roby14

3 жыл бұрын

@@ram43x80 Your not saving money that way. I was wondering if the starter would be more accesable. Now I know it clearly isn't.

@brettrichards1009

3 жыл бұрын

@@roby14 If you did take a look from the bottom, would it be easier? I have a lift.

@roby14

3 жыл бұрын

@@brettrichards1009 No. It sits below the intake and above the body of the engine.

Looking at this because my 2011 is having those cold cranks even though the engine is warm.. then i noticed your battery is an everlast as well.. im starting to think it might be the battery..

@YoDIYVideos

4 жыл бұрын

Swapping out the battery may be a good first step, that’s what I did. It didn’t help, unfortunately. If I had to do it over, I would’ve stuck with an OEM starter or rebuilt the starter if you have the bandwidth and time. The new starter I put in was a brand new one, aftermarket, AutoZone. There is some intermittent Long starts, still technically works, doesn’t work like the original

@pinnaclecooking2384

4 жыл бұрын

I have the drank sensor warning code and dealer is telling me it's because my aftermarket starter is spinning the shaft differently than a factory starter and I need to start there. What do y'all think?

@adventures223

2 жыл бұрын

@@pinnaclecooking2384 when you have to replace the starter again use oem thats all there is to say