2006 Honda Ridgeline CV Axle
Автокөліктер мен көлік құралдары
Parts Available At Amazon:
Fits 2006-2014 Honda Ridgeline:
Front Right Complete CV Axle: amzn.to/2MWcOqZ
Front Left Complete CV Axle: amzn.to/2JM4bxl
Rear Right Complete CV Axle: amzn.to/2pmnTII
Rear Left Complete CV Axle: amzn.to/2Jrs6Sr
00:00 - Intro
01:49 - Remove Sway Bar Link
02:16 - Disconnect Control Arm Ball Joint
03:28 - Remove Axle Nut
04:49 - Remove Axle
06:43 - Compare & Install New Axle
08:38 - Connect Ball Joint
09:06 - Connect Sway Bar Link
09:55 - Tighten Axle Nut
Пікірлер: 43
Can’t thank you enough for posting this video. Best of many KZread offerings on this subject. I rewatched the video this morning and then changed front left cv axel on my Ridgeline. Piece of cake except for a 10 minute wrestling match with the lower ball joint.
@davekingsley966
3 жыл бұрын
My 08 ridgeline is leaking grease, I see a axle change in my future. Great video 👍👍
@RustyHondas
Жыл бұрын
Bro Lower ball joint will never come off
job well done, sir!I was totally stressed because my passenger side wheel slipped off its' spline while I was changing the strut...(I know, I know). Now I know that it won't be such a big deal putting it back in place. Thanks a mil!
⚠️ Warning: do not try this approach if your sway-bar arm hex screws are seized to the bolt with rust (especially if you don't have impact wrench). If you try to turn rust-seized bolt from hex screw manually, it will strip. Then you'll need to saw off the screws and replace the entire sway bar arm. Much safer to do approach that disconnects the strut and knuckle.
@brandonmacdonald7802
10 ай бұрын
If your sway bar links are that rusty they probably need to be changed anyway.
Best video on this I've found so far. tHanks....and my Ridgeline tHanks you as well
Wow. So helpful! Fantastic video!!
Thanks for the video .. you do a great job ..
Thanks for the tip somebody told me I had to take the rotor the caliper everything but I will be doing this on my wish me luck
@uhyeahitsme413
4 жыл бұрын
I was told the same thing. Glad this is easier than expected. This video saved me from executing unnecessary steps.
@84blingbling
3 жыл бұрын
How hard was ? need to do this my self too but kinda scared
Good tips! Thanks
I saw another guy did the same thing on passenger side by only disconnecting stabilizer link. No need to disconnect ball joint.
What kind fluid was leaking? Is it from Hypoid Gear Oil from the transfer case?
they are not the same length!!!!!!! this is a big problem i running into now
Thanks for showing how to avoid the re-alignment. It should help me because I'm using cam bolts because of a 2 inch strut lift as well. I'll see if it works tomorrow. 👍
@nehemiahgrey625
3 жыл бұрын
you probably dont care but if you guys are stoned like me during the covid times then you can watch pretty much all of the new movies on instaflixxer. Been streaming with my brother for the last few weeks :)
@rivermemphis9170
3 жыл бұрын
@Nehemiah Grey yea, I've been using instaflixxer for since december myself :)
@colemayson1164
3 жыл бұрын
@Nehemiah Grey Yea, have been watching on InstaFlixxer for since november myself :D
Those axles are not the same size. Ridgelines are notorious for having problems with aftermarket axles.
@wanelly
3 жыл бұрын
Looks like he didn't notice...
@user-ze7tl2dw4i
3 жыл бұрын
@@wanelly yeah, I'm sure he has/the driver has by now lol the forums are pretty adamant about avoiding after market axles. The only okay stories I've heard are with NAPA gold, but even then I've read of problems with them.
@robertberin4872
3 жыл бұрын
Axles rarely go bad. Change the boots & or rollers
how do you change the inner boot. Mine is leaking grease but its clean.
@robertberin4872
3 жыл бұрын
@DONT BE SHEEP Nope. I changed the boot using the help of this vid & $13 ACDelco boot from rock auto. kzread.info/dash/bejne/aaaVk86Ro8-6Z6g.html
hey i have a 2010 honda ridgeline, i need a drive shaft replacement but i don't know which one i need. how do i tell?
@gtells
4 жыл бұрын
Caribbean Marine Care if you get a clunking noise in a turn to the right it is probably the front left axel and vice versa. There are a lot of other things that can cause noises so do your homework.
7:30 are you tapping it with a mallet or all by hand?
@APDTY
5 ай бұрын
By hand, however, we have used a ball-peen hammer on some other models. If you use a hammer, first put the nut onto the threads and then put the socket onto the nut, then hit the socket with the hammer. This Ridgeline, we just wiggled and pushed it in by hand until the clip snapped in.
Is this $60 axle still holding up?
Was it necessary to remove sway bar link? Can this job be done without removing it?
@APDTY
3 жыл бұрын
Maybe? Although it allows you to move things around a lot easier when disconnected.
What size nut is the lower ball joint?
@brianhunt793
3 жыл бұрын
19
@robertberin4872
3 жыл бұрын
Depends if you have the oem control arm or aftermarket. Stock is 19mm. Detroit axle is 21mm
Anyone having issues using aftermarket axles? I really don’t wanna shell out 500 in parts alone for new ones
@eluniversodelecuador
3 жыл бұрын
I like to buy “new” versus “re manufactured” NAPA Auto Parts sells decent CV Axles.
@robertberin4872
3 жыл бұрын
Junk yard
1500 for that t job expense
Aftermarket axles are always junk…
You damaged the customers ball joint boot when separating.