-Just did the torque mounts, and I found that a little bottle jack (2 ton Hyper Tough Walmart cheapy) was very helpful to the process (hat tip CrickiKaze B15 forum Mod par excellence). I advise installing both of the Tq-mount through bolts first, then the 17mm cross member bolts up front, then take the bottle jack and push up the rear into place (it is level & you have more work area). The crossmember bushings were shredded and I regret not acquiring them (unless you do the washer/wheel hopper jazz). I should note that I did support the tranny at some point as it was sagging & swaying like granny's handbag.
@srikarwarrior123Ай бұрын
Thank you so much for making the video.
@OXCFilms
Ай бұрын
Glad this video was helpful to you
@zacharygent18628 ай бұрын
One more question, when dropping the crossmember you said I can either support the engine OR the transmission. Meaning that either is okay ??
@OXCFilms
7 ай бұрын
Yes aslong as its not on the oil pan.
@zacharygent18628 ай бұрын
It’s only those four bolts to drop the cross member ? Or are there other bolts you have to take out before dropping cross member with mounts
@OXCFilms
8 ай бұрын
Yes from what we can remember its only 1 for each mount from crossmenber to engine and 2 bolts from cross member to body in the front and 2 in the rear
@zacharygent18628 ай бұрын
How sketchy is it lowering the transmission to get to the bolts? If I let it drop too much won’t it break something?
@OXCFilms
8 ай бұрын
Not sketchy at all. It only drops about a inch or 2 so nothing gets damaged or anything. We lowered it very slowly
@SuperJeyden8 ай бұрын
Hey where did you put the jack on the transmission to lower it ? Where is it safe to place?
@OXCFilms
8 ай бұрын
We put it right under it in the middle sections of the transmission. DONT NOT put it on the engine oil pan
@srikarwarrior12329 күн бұрын
Did the car rattle on bad roads with worn out mounts?
@OXCFilms
28 күн бұрын
No it was like clunking noise
@davidm3210 Жыл бұрын
Does the engine/transmission need to be supported when dropping the cross member? Nice tutorial, but next time no need to fast forward -personally I could have benefitted from watching the whole procedure, thanks.
@OXCFilms
Жыл бұрын
Thank you, we will keep that in mind when editing next time. No need to fully support engine/transmission you just need to put a bit a pressure on either of them to get the pressure off the crossmember bolts to pull them out.
@davidm3210
Жыл бұрын
@@OXCFilms Thanks jefe, one las question if I may be permitted: On the transmission mount, wouldn't it be easier to remove the nut instead of going after the recessed bolt head?
@OXCFilms
Жыл бұрын
The nut is actually welded to the body of the car, no way to remove it
@davidm3210
9 ай бұрын
@@OXCFilms Sorry but I got one more: Did you have all 4 wheels up for the cross member to distribute the tension, or are the front two alone jacked up adequate?
@OXCFilms
9 ай бұрын
@davidm3210 we only jacked up the car from the front. The rear wheels were still on the floor.
@armando5601 Жыл бұрын
The transmission one is hard to do
@OXCFilms
Жыл бұрын
Yes that one is a bit harder, but all you have to do is let the transmission drop a little but and you can get to the bolts
Пікірлер: 24
-Just did the torque mounts, and I found that a little bottle jack (2 ton Hyper Tough Walmart cheapy) was very helpful to the process (hat tip CrickiKaze B15 forum Mod par excellence). I advise installing both of the Tq-mount through bolts first, then the 17mm cross member bolts up front, then take the bottle jack and push up the rear into place (it is level & you have more work area). The crossmember bushings were shredded and I regret not acquiring them (unless you do the washer/wheel hopper jazz). I should note that I did support the tranny at some point as it was sagging & swaying like granny's handbag.
Thank you so much for making the video.
@OXCFilms
Ай бұрын
Glad this video was helpful to you
One more question, when dropping the crossmember you said I can either support the engine OR the transmission. Meaning that either is okay ??
@OXCFilms
7 ай бұрын
Yes aslong as its not on the oil pan.
It’s only those four bolts to drop the cross member ? Or are there other bolts you have to take out before dropping cross member with mounts
@OXCFilms
8 ай бұрын
Yes from what we can remember its only 1 for each mount from crossmenber to engine and 2 bolts from cross member to body in the front and 2 in the rear
How sketchy is it lowering the transmission to get to the bolts? If I let it drop too much won’t it break something?
@OXCFilms
8 ай бұрын
Not sketchy at all. It only drops about a inch or 2 so nothing gets damaged or anything. We lowered it very slowly
Hey where did you put the jack on the transmission to lower it ? Where is it safe to place?
@OXCFilms
8 ай бұрын
We put it right under it in the middle sections of the transmission. DONT NOT put it on the engine oil pan
Did the car rattle on bad roads with worn out mounts?
@OXCFilms
28 күн бұрын
No it was like clunking noise
Does the engine/transmission need to be supported when dropping the cross member? Nice tutorial, but next time no need to fast forward -personally I could have benefitted from watching the whole procedure, thanks.
@OXCFilms
Жыл бұрын
Thank you, we will keep that in mind when editing next time. No need to fully support engine/transmission you just need to put a bit a pressure on either of them to get the pressure off the crossmember bolts to pull them out.
@davidm3210
Жыл бұрын
@@OXCFilms Thanks jefe, one las question if I may be permitted: On the transmission mount, wouldn't it be easier to remove the nut instead of going after the recessed bolt head?
@OXCFilms
Жыл бұрын
The nut is actually welded to the body of the car, no way to remove it
@davidm3210
9 ай бұрын
@@OXCFilms Sorry but I got one more: Did you have all 4 wheels up for the cross member to distribute the tension, or are the front two alone jacked up adequate?
@OXCFilms
9 ай бұрын
@davidm3210 we only jacked up the car from the front. The rear wheels were still on the floor.
The transmission one is hard to do
@OXCFilms
Жыл бұрын
Yes that one is a bit harder, but all you have to do is let the transmission drop a little but and you can get to the bolts