Just finished working on mine. You do not need to remove any of these bolts on the back side. You need to remove the top pivoting bolt completely, and the bottom bolt that locks in position. However, the bolt is long and is against the chassy. Remove the 3 bolts, 14 mm, on the rear engine mount. Then put a jack under the engine. Lift it up just enough to extract the bolt. Then the pump falls down. Of course, you should remove the 16-mm rubber hose that feeds the pump and the high pressure outlet, but these are trivial. The pump is sandwiched between 2 steel plates and held in place by 3 bolts and 2 nuts.
@larrydimond97162 жыл бұрын
Good video. I have been fighting those bolts for hours. Thank you.
@LouisianaTractorworks4 жыл бұрын
You did that the easy way! lol Making all them other guys look bad!! lol Have a good weekend!
@MrMelvinkennedy1
4 жыл бұрын
Thanks. You to
@fedaiwoldu20542 жыл бұрын
Thank you! I was fighting the bolt over the high pressure hose.
@MrMelvinkennedy1
2 жыл бұрын
No problem
@theevangelist31743 жыл бұрын
I just did one on the same car this past weekend , it took me over 2 hours . 😀
@MrMelvinkennedy1
3 жыл бұрын
They definitely could have made it easier
@jasondroyd9373 Жыл бұрын
No need to remove those three bolts. From the front just remove the belt adjusting bolt and loosen the pivot bolt as far as you can (the bolt head will hit the pulley). The rear bracket will come out with the pump.
@Willyd2758
Жыл бұрын
How do you loosen the pivot bolt? I can’t see it anywhere
@bradyhouston4644 Жыл бұрын
Appreciate the info man
@MrMelvinkennedy1
Жыл бұрын
Absolutely
@yosvanirodriguez7499 Жыл бұрын
These are a pain, took me 2 hours even with a lift
@MrMelvinkennedy1
Жыл бұрын
Dang i hate that but glad you got it
@Mmamma805 ай бұрын
Thank you
@MrMelvinkennedy1
5 ай бұрын
Absolutely
@marka.27154 жыл бұрын
Where did you get that lift from and how much did it cost?
@MrMelvinkennedy1
4 жыл бұрын
Mark A. Amazon $2049
@xVxx65283 жыл бұрын
Is it the same for a 2002 Toyota highlander 3.0l v6?
@MrMelvinkennedy1
3 жыл бұрын
I honestly wouldnt know. Id think it would be similar but cant say for sure
@joshyjosh2142 жыл бұрын
What’s that long tool called
@MrMelvinkennedy1
2 жыл бұрын
Long tool? Extension?
@joenavarrete31944 жыл бұрын
I’m trying to get my pump off but I’m having trouble the 3 bolts your talking about in the beginning the 14 mm I can’t get them off . I use a ratchet in the front and a wrench in the back but no luck I noticed in your video you don’t show how to remove them , any advice?
@MrMelvinkennedy1
4 жыл бұрын
Joe Navarrete just seeing this but shouldnt be to hard. Socket, swivel, ratchet
@jamesjoseph24293 жыл бұрын
Where did you buy that lift? I want one!
@MrMelvinkennedy1
3 жыл бұрын
Amazon, its a xkusa mid rise lift
@canelamckee54able4 жыл бұрын
My pulley won't come off. I did the same thing as u and it just spun
@MrMelvinkennedy1
4 жыл бұрын
Canela History sorry just seeing this. You may have to use something to hold the pulley
@west_park7993
Жыл бұрын
take two strong pieces of metal. Drill holes on the 2 ends. Connect on end to the other to form a V-shape. Align the other ends with the holes of the pulley. Bolt them. No you have a lever to prevent the pulley to swing. Do not use impact wrench. Just a regular 17 mm box wrench, maybe extension.
@anthonyjarry42192 жыл бұрын
What about the first line
@MrMelvinkennedy1
2 жыл бұрын
Sorry just seeing this comment, im not sure which line you are referring to?
@stevec259110 ай бұрын
That's awesome if you have a lift if you don't it's useless
@TheRealMichaelP
7 ай бұрын
I jacked my car up laid down cardboard and did it on my back 🤷♂️
Пікірлер: 33
Just finished working on mine. You do not need to remove any of these bolts on the back side. You need to remove the top pivoting bolt completely, and the bottom bolt that locks in position. However, the bolt is long and is against the chassy. Remove the 3 bolts, 14 mm, on the rear engine mount. Then put a jack under the engine. Lift it up just enough to extract the bolt. Then the pump falls down. Of course, you should remove the 16-mm rubber hose that feeds the pump and the high pressure outlet, but these are trivial. The pump is sandwiched between 2 steel plates and held in place by 3 bolts and 2 nuts.
Good video. I have been fighting those bolts for hours. Thank you.
You did that the easy way! lol Making all them other guys look bad!! lol Have a good weekend!
@MrMelvinkennedy1
4 жыл бұрын
Thanks. You to
Thank you! I was fighting the bolt over the high pressure hose.
@MrMelvinkennedy1
2 жыл бұрын
No problem
I just did one on the same car this past weekend , it took me over 2 hours . 😀
@MrMelvinkennedy1
3 жыл бұрын
They definitely could have made it easier
No need to remove those three bolts. From the front just remove the belt adjusting bolt and loosen the pivot bolt as far as you can (the bolt head will hit the pulley). The rear bracket will come out with the pump.
@Willyd2758
Жыл бұрын
How do you loosen the pivot bolt? I can’t see it anywhere
Appreciate the info man
@MrMelvinkennedy1
Жыл бұрын
Absolutely
These are a pain, took me 2 hours even with a lift
@MrMelvinkennedy1
Жыл бұрын
Dang i hate that but glad you got it
Thank you
@MrMelvinkennedy1
5 ай бұрын
Absolutely
Where did you get that lift from and how much did it cost?
@MrMelvinkennedy1
4 жыл бұрын
Mark A. Amazon $2049
Is it the same for a 2002 Toyota highlander 3.0l v6?
@MrMelvinkennedy1
3 жыл бұрын
I honestly wouldnt know. Id think it would be similar but cant say for sure
What’s that long tool called
@MrMelvinkennedy1
2 жыл бұрын
Long tool? Extension?
I’m trying to get my pump off but I’m having trouble the 3 bolts your talking about in the beginning the 14 mm I can’t get them off . I use a ratchet in the front and a wrench in the back but no luck I noticed in your video you don’t show how to remove them , any advice?
@MrMelvinkennedy1
4 жыл бұрын
Joe Navarrete just seeing this but shouldnt be to hard. Socket, swivel, ratchet
Where did you buy that lift? I want one!
@MrMelvinkennedy1
3 жыл бұрын
Amazon, its a xkusa mid rise lift
My pulley won't come off. I did the same thing as u and it just spun
@MrMelvinkennedy1
4 жыл бұрын
Canela History sorry just seeing this. You may have to use something to hold the pulley
@west_park7993
Жыл бұрын
take two strong pieces of metal. Drill holes on the 2 ends. Connect on end to the other to form a V-shape. Align the other ends with the holes of the pulley. Bolt them. No you have a lever to prevent the pulley to swing. Do not use impact wrench. Just a regular 17 mm box wrench, maybe extension.
What about the first line
@MrMelvinkennedy1
2 жыл бұрын
Sorry just seeing this comment, im not sure which line you are referring to?
That's awesome if you have a lift if you don't it's useless
@TheRealMichaelP
7 ай бұрын
I jacked my car up laid down cardboard and did it on my back 🤷♂️