This is the best run-through of a diff pinion bearing/seal replacement that I've found here on youtube. Bravo!

It seems to have been very successful - no more noise, runs smooth and quiet!

a lot more depth than other videos was really good

good accurate installed ........helpul

good video, very detailed, thanks!

I don't own this truck but very informational video thanks

So the bearings need to be pressed into place...how long did it all take from disassembly up to where you were ready to reassemble thereabouts. Thanks.

استفسار يا أخوة جيب شيروكي 99 لما انحطه في D امورة طيبة على الأمام لكن لما تحطه في R ريوس مايرجع لمن لدية خبرة زين يفيدنا شكرا على تعاونكم معنا

The part starting at 5:50 is the most sophisticated, isn't it? That's why my mechanic declines to do the job. Does it only depend on the shims at each side? How many attempts where needed at your axle? Thx for this vid!

So the ranger has the same rearend as the mustang?Always thought it had the 7.5 rearend,so your info is good to know.Wish you couldve included replacement of the clutch packs too.Good solid well explained video

You need two step-down adapters - one for 1/2" to 3/8" and then another 3/8" to 1/4"

What did you use to remove the old bearings from the carrier and pinion, then install the new ones? Great video BTW.

What kind of paint you used to do load test?

yea were there some cups you pressed in for the pinion bearings? and nice job on the alignment with the yellow paint. you had it re machined and thats why you had to re chek it?

Very cool man, Thank you for the very informative vid...

Immensely helpful video!!! Thank you!

Should you match-mark the drive axle before you take it off?

where do i stick the hose to fill it? I just bought a ranger and the bottom lip is bent backwards and leaking.

what size is the pinion nut?

i have a loud knocking noise when i drive my mazda b4000 4x4. it has large tires and the 373 limited slip 8.8 rearend. i dismantled the diff and all of the bearings were tight, the pinion was solid and i noticed that when i moved the drive shaft with the tires on the ground the ring gear had signifigant movement as if the axles were worn!. im going to replace them with salvage units. is this common to wear out splines on axles of an 8.8? im a mopar man this is my 2nd ford lol

what sound dose it make if its bad

it is absolutely impossible to find a beam style inch pound torque wrench like you have to check the drag.... is there another way to do this step?

@aux1z11

5 жыл бұрын

29.95 Ebay all day

What size punch did you use to hold the pinion yoke?

thanks..very good.

@manuelchapadiaz1811

5 жыл бұрын

Tanks very good video, i have a Ranger 99 , bearings bad, bot , , Guadalajara México

Thank You Very Much, for the info. I have a 1991 Ford Ranger w/4.0 Engine that I'm planning on putting a 3:73 Ring and Pinion in. The only doubt I have is, how much rpm the motor could take especially when doing anywhere from 55 to 75 mph. I don't know if the motor could handle revving-at-3,000 rpm on the expressway. I would like to hear from anyone who has the 4.0 motor, Automatic Transmission and 3:73 Ring and Pinion Ratio. Like how many miles there Ford Ranger has and what had to be repaired. My motor, the 4.0, is rated at 160 hp at 4,200 rpm and red-lines at just under 5,000 rpm.

@km9097

6 жыл бұрын

1BlubeTube i have an 01 with 3.73 in an 8.8 and its good. Surprisingly quick for such little tourque. The rpms are fine no need to worry.

@aux1z11

5 жыл бұрын

Mine has a 4cyl with 8.8 with 5.13 gears and it's nice and zippy with 33,s

Would have liked to seen the bearings getting pressed on, what tools to use, etc. Otherwise it's good video..

Good job

step crown and pinion brings. sorry google translator

@hossamshahd7143

5 жыл бұрын

SOCRATES MARTINEZ م

Ma ktoś schemat plan diff ?

Rear nesfing wheel neafong

the sleeve of your shirt is ripped, its bothering me

@buddhudd1054

9 жыл бұрын

Hahahahaha

Sorry, but I have to say it looks like you did not crush the sleeve. You must get to that point where you crush the sleeve or it won't work. It may be quite for a while but then you will get whine on coast. Gotta crush the sleeve.