Dont mind the haters theyre not putting up their time to help others. Many ways to skin a cat. Thanks mate very helpfull!

@handymanPF

7 жыл бұрын

Thank you, I greatly appreciate that. Thanks for watching and commenting.

@moparerrnocar

5 жыл бұрын

Its called criticism, now go repeat what was demonstrated here and look for someone to blame when the bearing lip snaps and pops you in the face. Its one thing to act a fool, but dont post it publicly unless its to show what NOT to do.

@x-man5056

5 жыл бұрын

@@moparerrnocar Absolutely 100% correct Sir.

@apaulothegreat1581

4 жыл бұрын

I'm just a dumb old country boy only one way to skin a polecat double barrel 10 gauge shotgun that is simple easy problem solved

@eriv4735

4 жыл бұрын

I for one am glad the “haters” aren’t posting videos demonstrating improper and horribly unsafe “methods” for using SIMPLE tools

The puller goes underneath, you don't want pressure on the bearing itself, will make it harder to slide off.

Extremely helpful! I've got the same situation on a Mini Cooper Getrag 5 Speed transmission - too tight to get under the bearing. I think your approach will work in my circumstance. Thank you for sharing your expertise!

@frankfournier2177

6 жыл бұрын

i use a smalli bit grinder to cut race partly and then use a hamer and chisel to split much faster and safer

with no puller simply turh the shaft up the other way, apply heat to the race with propane torch till the race fall off. millwright for 35years

@superbestdad

7 жыл бұрын

If the pinion or ring gear are to be reused you might not want to heat the part. The hardening is important. You do what you have to, just saying

@MrBrobilly

7 жыл бұрын

If its going to be reused you dont have to take it off. if you are gentle with the heat it wont hurt it, 250 degrees will do it. It will fall off when it expands. oils starts to smoke at 300 degrees, the bearing wont get hurt till 350. and there will be a lot of smoke, oil can flash after that.

@superbestdad

7 жыл бұрын

MrBrobilly on a GM pinion maybe but on most others the press fit is too tight, if I'm not mistaken you only get about .001" expansion for every 100 deg F. And the temp required has to be quickly added to keep the pinion from leeching and expanding. I've done it this way many times when I started working but have evolved and found better ways. For the sake of the do it yourselfer your method does work, use caution though

@charliedee9276

5 жыл бұрын

If you have a welder a bead run on the race being removed will allow it to pretty much fall out also. I have removed many hub bearing races from old Harley wheels with that method.

@MrSexoda

5 жыл бұрын

I always sat the gear in an ice water soaked rag when heating the race. And I've found if you try to concentrate the heat in one or two places rather than the whole thing it works better and faster. Never once did the shaft change color( which is a sign of weakening the heat treated steel.). Changed them on all different kinds of shafts like the differential plus many different differentials from cars to semis to large boats even. Even if it doesn't fall off , a screwdriver or small pry bar always was able to get it off.

Pulling that bearing off by the cone front face rib is a good way to loose an eye or break your teeth when the bearing breaks under the force of the puller. If you are going to do it that way at least wrap a rag around the bearing to contain the shrapnel. Trust me I am a millwright in my 60's and have been hit in the teeth from exploding bearings not to mention the people I have worked with over the years that have sight in one eye only from removing bearings in an unsafe manor. Do it right or don't do it at all.

@pupdog7374

7 жыл бұрын

I agree. Too many people with no experience about bearing removal are giving advise on KZread.

@irondiver292

5 жыл бұрын

oto169 what local?

@DickRichie510

5 жыл бұрын

Im industrial mechanic ill have to agree

@MrGGPRI

5 жыл бұрын

I would be wearing a welding helmet. Using a die cutter to snap-off the race would be safer.

@j7ca

5 жыл бұрын

Duh... china tools are cheap... who knew ???

This is not the way the removal kit is intended to be used. The two cheeks should be fitted at the base of the bearing and gradually tightened. They act like a wedge. It is not necessary to remove the roller cage

@handymanPF

7 жыл бұрын

+paul c there was barely any clearance between the pinion and bearing To do it the textbook way. So I improvised and I survived. As a disclaimer again: these videos I make are videos on how I go about doing things. Only used as information purposes only. With that being said, this will be my last comment to this thread. Thanks for watching and commenting. I greatly appreciate it.

@jerryreynolds1334

7 жыл бұрын

exactly!

@handymanPF

7 жыл бұрын

Mike M that's correct. I did not reuse the pinion gear because I bought a new ring and pinion set. But I only thrashed the old bearing and not the pinion gear itself. I did it the way I did because of the lack of clearance between the bearing and pinion. I hope you found this information useful. Thanks for watching and commenting. Please like, share, and subscribe.

@dillonwarman7769

6 жыл бұрын

He's lucky the inner edges of the puller didn't slip off the top of the race, did you see the deflection on it ha talk about dumb luck.

Just an idea something I Do once the bearing has pulled up enough. It’s a good idea to re rig the set up and grab the race from the bottom where the pignion gear. You get more meat to grab I have seen the upper lip crack and shatter. Just something I do and would recommend also I like to use a hydraulic press with the bearing separator but when you don’t have hydraulic press then the old screw press works

Thanks for taking the time to show how you remove the pinion bearing. I am using the same tool and it's just not moving so now you have given me another way to try it.

@handymanPF

4 жыл бұрын

Be careful. It is dangerous like this. Cover it with a a heavy blanket or something of the sort just in case something does break. Wear eye protection too. Safety first. Good luck. Thanks for watching and commenting. Please like share and subscribe

A bigger impact gun has a hammering effect and it seems to make them come off easier. Heat helps too. Split many in half by grinding a slot and sticking a cold chisel in and hitting with a mini sledge. Put the bearing puller under the race too. Much harder to shatter it that way. Putting it on the upper lip leaves just a little material to rely on for strength. Putting it under the bottom is a lot safer. My preferred way is with heat though. Fun to watch it drop off when it gets hot. Also putting the puller under the bearing before cutting the race off ends up compressing the rollers against that inner lip you see handy man lock his puller on. That way the all press against it and you have a pretty strong set up.

Thank you, a very informative video! Helped me a lot as a first timer!

@handymanPF

5 жыл бұрын

I’m glad you found it useful. Thanks for watching and commenting. I greatly appreciate it. Please like share and subscribe and hit the notification bell to stay up to date for new videos. Thanks again

Good lesson....Thanks

Watching you try and cut that Bearing Cage with those snips was like watching a turtle try and eat a tomato.

@thecatfelix2988

6 жыл бұрын

Sassy badger. 👀😄😄

@rsz90182

6 жыл бұрын

SassyBadger I was gonna say a new born playing with a rattle. LMFAO!

@almenz339

Жыл бұрын

Oh that’s good! 😂

Shouldn't the puller be on the bottom part of the bearing race. I always found that adding some heat makes the job easier.

@bryanmartinez6600

6 жыл бұрын

Joe SC thermal expansion is a great thing indeed

@ashokbamanalli338

6 жыл бұрын

Joe SC both way it can be removed if the puller reach is adequate

@ashokbamanalli338

6 жыл бұрын

Joe SC right

@alexlairson4759

3 жыл бұрын

No, not job easier. I tried today and still completely stuck.

@timjohnson1199

2 жыл бұрын

And, less chance to score the shaft.

I took mine to the machine shop, had them pull it and then turn down the pinion where the bearing would just slide on and off. when the rear end wasn't right the first time I could adjust it and just pull the bearing off. no more machine shop. great!

@BeeftallicA

7 жыл бұрын

You have to be trolling. That is probably the dumbest thing I have ever heard. Inner races are press fit for a reason. How long before you fried the pinion? SMDH.

@philgrimes6137

7 жыл бұрын

No elliston, you're full of shit. They are pressed on because they are easier to set up when they won't move. You don't know what you are talking about. You're the troll.

@BeeftallicA

7 жыл бұрын

I'm glad you made yourself a "setup pinion" bahahahaha

@larrychristopher9147

4 жыл бұрын

TURN THE PINION DOWN??? CAN'T FIX STUPID

Good work, man! Very well presented!

@handymanPF

8 жыл бұрын

+alwcurlz Thank you. Glad you liked it. Thanks for watching and commenting.

Great video, and I agree removing the bearing cage will help. However, the tapered halves should slide between the bearing and pinion as the pinch bolts are tightened. Above all else, be careful. Use a heavy rag around the race Incase it shatters.

@handymanPF

5 жыл бұрын

You do bring up valid points and I agree. I greatly appreciate your comment greatly. Thanks for watching and commenting. Please like share and subscribe. Also please hit the notification bell 🔔 to keep up to date of upcoming videos. Thanks again

@crazyantny9161

Жыл бұрын

I have the easiest way. Just leave the old one on if it not a mess

Hi Handy Man, Thanks for taking the time. I'll look for a puller kit now. I saw your link to a reasonably priced set in the comments. Good vid, Cheers

@handymanPF

9 жыл бұрын

Thank you for commenting. I m glad it helped.

Nice Bud Thanks !~!~Adding That kit To My bucket list !~!~

@handymanPF

5 жыл бұрын

It’s a great tool to have. Thanks for watching and commenting. Please like share and subscribe.

Gotta do this in my 02' Blazer ZR2. Everything is tight & I had 3 shops tell me that the noise was a bad wheel bearing. I changed the 2 Hub Assemblies in front & the Rear Bearings & seals only to still have that noise. Then we figured out it was my pinion bearing. $300 for a shop to install, so I'm letting them do it.. That's with me buying the parts.

The puller is stronger if installed upside down from the direction you used. With the offset of the puller rods it will tend to clamp tighter in the other direction. And yes the part is correctly called the bearing race.

@handymanPF

8 жыл бұрын

+Dick Mick great tip. Thanks for watching and commenting. Please like, share and subscribe.

@superbestdad

7 жыл бұрын

The silver part that's being refered to as a puller is called a bearing splitter. the splitter can be used many different ways but the way it was used in the video is one of the most cringe worthy ways. if you watch the splitter as torque is applied, you can see the splitter bolts start to bend. a little more torque than he used and lovely warm shards could find their way into your skin or eyes. Been there, Done that

@superbestdad

7 жыл бұрын

oh man im laughing. tell a guy named dick "great tip"

You can also cut the bearing off if you have a steady hand

very helpful. Great easy job. Thank you.

@handymanPF

7 жыл бұрын

I am glad you liked it. Thanks for watching and commenting. I greatly appreciate it. Please Like, share and subscribe.

The clam shell is the easiest way to do this. You got the job done good vid

Very helpful, thanks for the video bro

@handymanPF

5 жыл бұрын

Great, I’m glad you found it helpful . Thanks for commenting and thanks for watching. Please like share and subscribe.

efficient video, you got right to the process. Thanks

@handymanPF

8 жыл бұрын

Thanks for commenting and watching. I greatly appreciate it. Please Like, share, and subscribe.

This was more than a few years ago. The one thing that spooked me was the bend you were getting in the bearing separator bolts.

@handymanPF

4 жыл бұрын

Yeah it was quite a bit ago also that was bothering me also the bend in the bolts. But I had no room to get it between the pinion and the pinion bearing.

@seannot-telling9806

4 жыл бұрын

@@handymanPF At the time you do what you have to do. If you had access to a larger splitter the bending would of been less do to larger bolts. The worry about the smaller splitter is that it could pop off the bearing your pulling and hurt someone. As some have said wrapping the assembly in a towel would be a good idea to slow any parts that might come flying off of something were to slip or break. Stay safe.

@handymanPF

4 жыл бұрын

Now that right there is proper and respectful criticism and advice. Very well put. Have a great new year.

@seannot-telling9806

4 жыл бұрын

@@handymanPF Thank You. You also have a Good Safe New Year.

I have two sets of bearing puller and I'm able to pull the whole bearing off without any damage if I use my OTC puller. My Armstrong puller has a shorter taper so it will damage the bearing if you don't pay attention to it.

wow man what a great video!

sometimes i'll use a die grinder with a small cutoff wheel to cut a groove in the inner race and than hit the groove with a chisel and crack the race, or run a bead of weld around it and tap it off, all depends solely on the feels of that day.

@josepeixoto3384

6 жыл бұрын

TWO great solutions people,have done that many times.

@bjr2379

5 жыл бұрын

I once hit an inner race with a chisel. The cutting edge of the chisel is still in my leg.

First time I've seen that thank you.

@handymanPF

4 жыл бұрын

I’m glad you found it useful. Thanks for watching and commenting. Please like share and subscribe and hit the notification tab.

i c u like to do things the hard way

@DONNIEWATKINS

5 жыл бұрын

Nice !~!~!~

Good video handyman. Really you don't have to buy a kit at all. I went to autozone and they have a kit you can rent. Works great. Thanks for the video.

@handymanPF

9 жыл бұрын

Yeah you can do that, I ve done it. Thanks for watching and for the comment.

pretty cool.

Thank you fot your time and knowledge!

Do you know what tool is used to put the little yellow springs back in to the differential?

Thanks!! good to know

@handymanPF

7 жыл бұрын

Im glad it helped.Thanks for watching and commenting. Please like, share, and subscribe.

Agree with alot of comments here, simply adding heat will make this job a lot easier. For the safety of people watching this, assume the bearing / pullers will break so protect your eyes/face!!

Sometimes you can put the whole thing in the freezer, take it out, put a little heat on the bearing and slide it right off. To put the new bearing on, do the same thing. Don't put the new bearing in the freezer...just warm it up...lol

@superbestdad

7 жыл бұрын

always a great technique for home do it yourselfers, we all have ovens and freezers and time

@ws678ta

5 жыл бұрын

Yes, that works great. It is only .0015 interference fit.

Thank you. Very helpful.

@handymanPF

7 жыл бұрын

I'm glad you found this helpful. Thanks for watching and commenting. I greatly appreciate it. Please like share and subscribe.

Even though this is a fairly old thread, it is still relevant! In comments below, MrBrobilly had the closest solution to do this bearing removal. However, there is one more stage to actually making sure that the bearing will simply slide off or gently pull off and thus avoiding any potential damage to the shaft or the thread end. Once you have the Pinion out, wipe excess oil off and then put the Pinion into a plastic bag and then put into a freezer for an hour. Place the Pinion on a bench with the bearing facing down and then apply gentle heat with a propane torch to the bearing circumference and the bearing should expand and fall off. Do not apply heat to the Pinion!! If the bearing doesn't fall off, just repeat the process of freezing the Pinion and bearing, remove from the freezer and attach the puller and apply heat again to the bearing only. You will be able to remove the bearing by hand. Remember that in life; what a man can do, a woman can do better. Be fair warned! By the way.. When installing the new bearing. Never pound the bearing on! Clean off the Pinion shaft and put back into the freezer for an hour. Prepare the bearing by warming the inner bearing race to about 140-F degree. Take the Pinion out and place it upright on the bench and put a little oil on it, put oil on the inner race and slip the bearing over the Pinion quickly. It should slip all the way down and seat itself. If not sure, then tape it down with the old race or a socket!

Thank You ! This was immensely helpful !

@handymanPF

2 жыл бұрын

Thank you for watching and commenting.

Good info now can you make a video on how to remove the bearing without damaging it?

Wait. What? No. The round wedge shape of the puller halves are meant to go beneath the bottom of the race in which to use the bolts to wedge the halves together wedging the race upwards. But you're doing great. Everybody learns something the hard way sometimes.

Nice one, good video. As a rally mechanic , I hit it on edge with a snap on chisel, cracks on second hit, job done. But you did a great job there with the correct tool. So many "know all's" on here, everyone gets by in the end.👍

@handymanPF

6 жыл бұрын

Thank you, I greatly appreciate that.

THANKS BODY!.... i have everyting to build that puller on my shop great advice!...

@handymanPF

8 жыл бұрын

I'm glad you liked it. Thanks for watching and commenting. I greatly appreciate it. Please like, share, and subscribe.

I'ce always used the bearing seperator to wedge in between the bearing and the pinion. This is likely smarter to not damage things and less wear on the tool. I enjoyed the Nailbomb audio clip at the end.

@handymanPF

9 жыл бұрын

Yes that is correct. But when you have no room to fit the tool behind the bearing and pinion, than this is one of the other alternatives that you can use. Thanks for watching and thanks for the comment.

I'd have heated it up a little bit with a propane torch. Heat up the race and it might just fall right off.

Cut it with a 4inch grinder wheel. Tap the cut with a chisel!!! Way faster !!! But over all that is the proper tool to do the job !

Thanks man good job!

@handymanPF

6 жыл бұрын

Thank you. Glad you liked it. Thanks for watching and commenting. Please like share and subscribe.

You don't need to remove the cage and rollers to pull the bearing with this tool. Just grab the inner race between the gear head and the bearing. Also you risk stripping out the threads on the forcing screw by not lubricating the threads and by using a power tool. Been there, done that. Lesson learned.

@ 2:30, it's called the 'inner race'. ;)

@Demonslayer20111

6 жыл бұрын

fuzzy wuzzy why because he actually had something usefull to say

wow, something easy to remove took long time.

When you place the top bracket on, The bolt or nut on the top left was not snugged down before you put the extractor in place.

Made it look easy. thanks.

@handymanPF

7 жыл бұрын

+1080sucks I'm glad you liked it and hope you found it useful. Thanks for watching and commenting. Please like, share, and subscribe.

I did one of these. I think you can get under the bearing with the splitter and remove it w/o damage

Great information!!!!

Good job, every one is a critic but your method worked great. I was ASE cert in auto, medium, HD truck for 25 years and used the same method often. Thanks for taking the time to make this nice demo vid. Take care, Joe

@handymanPF

8 жыл бұрын

Thank you for watching and commenting. Your opinion is very well appreciated. Take care.

@superbestdad

7 жыл бұрын

i call bs on you sir.....bs I AM a mechanic of 25 years and about 3 or 4 jobs in you grow up and buy big boy tools.

Profesional my frend.

wow some of the people on here have really good ways of do the job! but, the 1st tool he used is called a bearing splitter & if he had used it correctly he could of had it off alot faster!! the splitter goes between the pinion & bearing with the same flare side up like he had it. then tighten the nuts and then the splitter will force the bearing away from pinion. then use the rest as he did and presto off quicker!!!!

@josephmartin2362

5 жыл бұрын

The splitter is too small to do the job properly. Otherwise your comments are correct.

@abdulhassan1107

3 жыл бұрын

I tried that without cutting off the cage and it worked fine. The old bearing is still reusable. But it wasn't easy. I need to do it again to change the shim and I hope I don't damage the new bearing so I'll use a heat gun first.

@johnnyonnotice

2 жыл бұрын

Exactly

@johnnyonnotice

2 жыл бұрын

First guy to say it.

@johnnyonnotice

2 жыл бұрын

You got it

i put on other bearing upsidedown and heat it up and at the same time i spin it, it falls down. easy.

Once you are down to the raceway, just heat one side with a propane torch for about 3 minutes and it will slide right off. The raceway being of much less mass than the Pinion Shaft will expend much faster than the Shaft. What you did was dangerous as hell.

I brought the same, slipped a couple of times, thought it wasn't going to work there was bang and the bearing popped of, wouldn't have got the bearing off without it, thanks

Put the bearing puller behind the bearing bolt on down and put the thing in the press. Take less then 60 seconds.

Outstanding!!

why do you have to destroy the bearing? the kit won't get underneath with the cage still intact? i was planning on saving the old bearings for setups. thanks.

@handymanPF

8 жыл бұрын

+Jacob James on this one is because I didn't have enough room behind the bearing to put the tool. I hope this helps. Thanks for watching and commenting. Please like, share, and subscribe.

@superbestdad

7 жыл бұрын

never make used bearings set-up bearings. your set up will be way off when the new bearings and races are installed. Using a bearing splitter like the silver part of the puller set he is using could be used under the cage, this will roll the bottom of the cage and basically ruin the bearing. the puller that will not harm pinion bearings or carrier bearings is a bit over 400 us so $20 bearing....$400 puller.....you choose

@guntipradeep2922

7 жыл бұрын

handy man

@MrMusic1950

6 жыл бұрын

Jacob James I have always used the part he cut off to pull the bearing, it's way quicker and easier.

@jacquespoirier9071

6 жыл бұрын

if you use a cold chisel to wedge the bearing, often it will move enough to permit the installation of the bearing plate, this manoeuver is risky and you must be very attentive to not gouge the pinion.

thanks

@handymanPF

8 жыл бұрын

+juan Figueroa no problem. Thanks for commenting. Please like, share and subscribe.

Thanks for the great educational video 👍💯

@handymanPF

Жыл бұрын

Thank you for watching and commenting. I greatly appreciate you. Have a great day

awesome! thanks a milion

@handymanPF

8 жыл бұрын

I'm glad it helped. Thanks for commenting and thanks for watching. Please like, share, and subscribe.

Nice!

My Only Suggestion Is start out Like That to get separation Then Flip Your Brackets So They Don't Force The Taper To Make Sleeve Tighter to Pinion Bolt With The Taper Down It May Pull easier ? definitely Getting This Tool !!~!~

@handymanPF

5 жыл бұрын

That’s not a bad idea. Thanks again.

Mine didnt work the two studs that hold the pullers together bent and made the extenders all crooked and i eventually broke one of them.. lol but then again nothing ever goes my way

now I gotta figure out how to remove the carrier bearings!

i just bought the same exact tool, however it bent and broke on me, any suggestions on how to use it properly?

@rosseowens

3 жыл бұрын

Same here.

Thanks helped me out here where did you get the bearing puller

@handymanPF

7 жыл бұрын

+Kelly no name thanks , I'm glad it helped. You can purchase the bearing puller from here amzn.to/2nsFA7v . Thanks for watching and commenting. Please like share and subscribe.

What about if i want to remove the bearing withou dammaging it? i.e to put shimms under it during adjusment phase of re-assembly?

@handymanPF

7 жыл бұрын

+Alan Adams with it having a very tight tolerance and not having enough room between the bearing and pinion to fit the tool in, it would be difficult. What I did is bought 2 pinion bearings. Machine inner diameter of the dummy bearing so it barely slipped on and off with no problem and then I adjusted my shins that way. Once I have all my proper shims then I install the new pinion bearing. I hope this helps. Thanks for watching and commenting. Please like, share, and subscribe.

The puller may be upside down as those two horizontal bolts bend, then the catchment area opens up and could slip off the lip of the inner cage. If turned upside down the bending in the two puller horizontal bolts would. would press under the lip of the inner race. I think I would have used a welder to do that job.

Great video, is it possible to not cut the bearing off to remove a bearing without breaking it?

@pjames4413

Жыл бұрын

Yes, absolutely.

How do you put it back on?

Very nice..👍

@handymanPF

6 жыл бұрын

I’m glad you found it useful. Thanks for watching and commenting. Please like share and subscribe.

Great job My_Friend... you got 'er done... more than most!!! Many will gain knowledge from your effort!!!

@handymanPF

5 жыл бұрын

Thanks. Thanks for watching and commenting. Please like share and subscribe

i had that tool bought it for the sole purpose of doing the rear diff on a dakota just sold it a month ago because it was useless to me i now have a repaired press somebody threw out haven't had to use it yet.

Thank you

@handymanPF

3 жыл бұрын

Thanks for watching and commenting, I greatly appreciate it. Please like share and subscribe.

Well this is good if you dont reuse the bearing, but how to pull of a bearing if you are setting the pinion depth in the beginning? Thanks

Very good

@handymanPF

6 жыл бұрын

Thanks. I’m glad you found it useful. Thanks for watching and commenting. Please like share and subscribe .

Como se ajusta el piñon con la corona

The setup at 4:00 I think I would try by opening up my vise and allow the tool to rest on top off the jaws then hit the pinnion with a dead blow.

@jacobjames1171

7 жыл бұрын

That setup looks scary.

Good man

@handymanPF

6 жыл бұрын

Glad you liked it. Thanks for watching and commenting. Please like share and subscribe.

The puller is upside down, lol

👍good vid

@handymanPF

4 жыл бұрын

Thank you

hey Hman, this looks like it will work on ANY bearng mounted in a flush situation. I am learning if I can pull the tapered bearing at base of a motorcycle's steering stem. Exactly the same flush install. I will look for this style puller and remove the roller cage. Great teacher, thanks. P.S. rename the video title that gets searched to something like bottomed-out bearing removal or whatever the correct terminology is. If that helps.

@handymanPF

9 жыл бұрын

Thanks for watching and the compliment , I m glad it helped.

@superbestdad

7 жыл бұрын

bearing splitter and a press

Cut the cage off? What about when you are doing your setup and you have to pull the bearing to add or subtract a shim?

@handymanPF

7 жыл бұрын

Since it was so tight against the pinion, I seen this as my only option. What I do it buy 2 pinion bearings. Home one so it slides on and off the pinion smoothly but with a slight snug. Then I measure my shims. Once I have that figured out then I remove the dummy bearing and install the good one. Glad it helped. Thanks for watching and commenting. Please like, share, and subscribe

Very nice

@handymanPF

7 жыл бұрын

I m glad you liked it and I greatly appreciate your comment. Please help support this channel by liking and subscribing. Again thank you for watching and commenting.

Is there any of what you would consider 'hammering' or percussion on the threaded center shaft in the operation of this tool? Thanks.

@handymanPF

8 жыл бұрын

+Tae Ken Do no not recommended, because hammering could damage the threads and or distort the shaft. I hope this helps. Please like, share, and subscribe.

@TaeKenDo

8 жыл бұрын

Ok because another youtuber does a review of the same puller and says you need to hit it with a hammer, then a turn with the wrench, then another hammer blow (light) then another turn with the wrench, etc...until it's off. I dunno but I thought puller were supposed to to the job for you by pulling not pushing with hammer blows...lol Thanks.

Anyone who has never done this before should do some reading on how to set up the diff or rear end assem. You will need a dial indicator and toque wrench to set it up properly.

@superbestdad

7 жыл бұрын

reading good, marking location of parts removed better, pay attention. If you put things back like you found them except new bearings and seals then the set up hasnt changed. still need the torgue wrench but honestly the home do it yourselfer most likely wont make it past the crush sleeve install.

Nice video

@handymanPF

7 жыл бұрын

I'm glad you like it and found it useful. Thanks for watching and commenting, I greatly appreciate it. Please like, share, and subscribe.

I see why you took to rollers out . nice work. different way of doing things.

@handymanPF

7 жыл бұрын

Great, I have tried to explain it over and over again but some other people do not understand. Thanks for watching and commenting. I greatly appreciate it. Please like, share, and subscribe.

That bearing remover kit does not fit a Toyota Differential

Just run a bead of weld around it, after you take the cage and rollers off. Let it cool... turn it over, race drops right off. Much easier!

Great video. I found that puller set on Amazon for under $60. :)

@handymanPF

8 жыл бұрын

Thank you. Thanks for commenting. Please like, share, and subscribe.

@fosgate375

8 жыл бұрын

Well, at least the guy can spell.

@SouthFlaDiver

8 жыл бұрын

Harbor freight 45.00

instead of destroying the bearing why not slide the whole thing out with the puller...