1947 Ford 2N - Behlen rotary mower (brush hog) #4, Home made "Stay chains"

Фильм және анимация

Thanks to a couple of comments on my other videos, I was inspired to install my own "stay chains" on the 2N. The tractor does not have accurate position control, and I needed the deck height just a few inches off the ground for mowing my thick fields. This mod did the trick. I also have room to adjust the brush hog lower for a tighter pass.
Thanks again for those who made this suggestion. And, maybe this video will help somebody else out there with the same issue.

Пікірлер: 15

  • @d.pierce.6820
    @d.pierce.68204 жыл бұрын

    On my 8N, I had a couple of flat plates that fit on either side of the top link-they each had a "keyhole" cut in them-you would pull the chain through the upper part of the keyhole, and when you got the right length, you turned the chain sideways and dropped a link into the lower slot of the keyhole, locking it in place-worked real well for setting whatever height you wanted.

  • @lareemcra347
    @lareemcra3473 жыл бұрын

    My Fergie would leak down the cutter, so I mounted a couple of chain hooks on it, put chains on the front of the cutter, set it and chained the cutter to the tractor. It worked quite well. I was surprised at the mowing power of the old tractor.

  • @donmacdonald7758
    @donmacdonald77584 жыл бұрын

    The old girl needs sway bars to stabilize motion from side to side,but did a good job. I own a 39 9N.

  • @Just_Chuck_It
    @Just_Chuck_It3 жыл бұрын

    To make attaching implements easier, you should install a set of PATS quick change hooks. Then all you have to worry about is your top link.

  • @michaelt5082
    @michaelt50822 жыл бұрын

    Thank you, it helped and I purchased my stay chains. I have 8 acres to tame and I can now do it. Thanks for showing your setup. I believe that one will work for me. Oh ya I am on a Ford 600. :D its nice and I can work on it :D No computers needed lol

  • @AntiqueCarsandStuff

    @AntiqueCarsandStuff

    2 жыл бұрын

    Glad the video was helpful. Thanks for watching!

  • @richardgreen7811
    @richardgreen7811 Жыл бұрын

    Scary to me. I have 100's of hours bush-hogging with the Ford 8N. The most important factors were the sway-bars (which you don't have installed) and the over-running clutch on the PTO shaft (which it appears you don't have). Level can be controlled with the height of the rear wheel and adjustment of the 3-point attaching bar. The over-running clutch will save your life. I'd advise checking Tractor Supply real soon.

  • @AntiqueCarsandStuff

    @AntiqueCarsandStuff

    Жыл бұрын

    Good advice. Thank you.

  • @robodrone4004
    @robodrone4004 Жыл бұрын

    On that type of tractor with a brush hog, please don’t use that type of top link. It is dangerous. If you hit something with the mower, it can violently kick upwards from the back and shove the top link through the casting and into the driver. Can cause a very serious injury. Simply use a chain for a top link.

  • @kennethstout5616
    @kennethstout56164 жыл бұрын

    Extend the top link to regulate the front height of the bush hog. No need for chains.

  • @chrisfleming3116
    @chrisfleming3116 Жыл бұрын

    What lengths haft you running on there?

  • @henrysosebee9241
    @henrysosebee92414 жыл бұрын

    Hope you have a overriding clutch on pro

  • @henrysosebee9241

    @henrysosebee9241

    4 жыл бұрын

    Can’t spell should be pro

  • @henrysosebee9241

    @henrysosebee9241

    4 жыл бұрын

    Phone needs to learn how to spell PTO

  • @AntiqueCarsandStuff

    @AntiqueCarsandStuff

    4 жыл бұрын

    Yes, some folks swear by those but I have not had any problems at all. I guess I'll look into it and consider. Thanks.

Келесі