awesome video! very informative and interesting. looks like a lot of fun

@CarRemap

2 жыл бұрын

Thank you mate! I'm doing my best to make entertaining videos and to motivate people to get started :)

I welded that EGR-Pipe and had better circulation in lower revs with higher air speed. But very nice project. I asume that was a lot of fun.

@CarRemap

4 ай бұрын

For real ? You mean where I put my EGT probe ? If it improves low down torque I will definitely do it! Thanks, yeah nice to work on and still unfinished!

I have thé same Awesome car

Very nices what what is The BHP of this polo??

Hello! Im impressed with this video as I just got a skoda roomster 1.4tdi Do you sell these parts on commission? Thanks in advance.

Hi there same engine and gearbox as you but in an Audi A2, was the clutch and flywheel a direct fit? Or was modification needed as I was always told that the clutch and flywheel in the 1.4’s were smaller diameter than the regular 02J boxes so the G60 flywheel wouldn’t fit. Thanks

@CarRemap

2 жыл бұрын

Hi, yes the clutches for 1.4 exist in 216 and 220mm sizes. if you put a JDD gearbox (02R) or a 02J, the G60 flywheel will fit along with a 228mm clutch but not with the original 02T gearbox (BNM engine). However it will work with the stock gearboxes of BNV, AMF, ATL and BHC engines. If you have the spacer between the gearbox and the engine, you'll need to remove it and change the engine mount. I noticed in my gearbox that the pressure plate rubbed a little bit near the input shaft.

Hi my friend. Did you feel the smell of exhaust gas and excessive smoke by removing the catalytic converter? I’m unsure whether to fit a Darkside downpipe (without catalytic converter) or a 200 CPSI metallic catalyst…

@CarRemap

Жыл бұрын

Hello mate, not gonna lie, it's not terrible but it definitely smells specially with a cold engine. I even made my downpipe so the stock cat can be reinstalled in a few minutes and for now it's back on the car. There is no excessive smoke though

3 cylinder?

Sa marche fort

With original Gearbox?

How much boost?

did you renew balancer chain before this upgrade? i also thinking about stage 1 remap but i dont thrust balancer chain.

@CarRemap

Жыл бұрын

Yes I changed the tensioner and the chain

@sameshitdifferentcolour4197

Жыл бұрын

@@CarRemap did you feel any diference before and after the new chain? vibration decrease or increase? i have 1.4 tdi bnv engine idle vibration increase slowly during last 10 years 225k km on dash. i wonder chain stretch can cause balancer weight misalignment and lead to increased vibration.

Hello, Ist the Engine Stock? Piston and connecting rod? Great Power!!!

@CarRemap

3 ай бұрын

Thanks, yes internals are stock

Hey, im new to tuning diesel and i have a question. The injectors you said are 550cc AFR, you mean they are the same injectors that are in 1.9 TDI AFR?

@CarRemap

7 ай бұрын

Hello, I don't exactly know what you mean by AFR but yes, they are the same as found in 1.9 TDI PD ASZ, ARL, AVF (038130073AL)

@kacperbocianski7337

7 ай бұрын

@@CarRemap Thanks, and also i write it wrong i mean "ARL"

Can you tell me what year it is? In what year does FAP mount dpf?

@CarRemap

Жыл бұрын

Car is from 2008. Eco models like bluemotion have BMS engine which carries a DPF.

could you please post a link to the exhaust? this is the only part i'm struggling to find

@CarRemap

Жыл бұрын

I did the downpipe by myself mate, not sure if it exists for the polo with GTD V-Band

What engine code was it and did you use a vnt turbo or wastegatev

@CarRemap

2 жыл бұрын

Engine code is BNM 70hp, yes the 1752VRK is a vnt turbo

Good job! Why did you leave the original exhaust muffler? Isn't it underpowered for the needs of the engine? I also have a 2006 9N3 1.4 TDI BNM...

@CarRemap

2 жыл бұрын

Hello, you are right! This might be one more step along with a bigger intake from the airbox.

@federicolorenzoni245

2 жыл бұрын

@@CarRemap You can install a Seat Ibiza Cupra 6L 1.9 TDI 160 HP air intake (cod. 6LL 129 618 / 6LL 129 621). I've installed it.

@CarRemap

2 жыл бұрын

​@@federicolorenzoni245 I made that part by myself, the big restriction is after the airbox to the turbo inlet. Ideally a custom aluminium one should be a great improvement. Tell me if you find a solution for the 1.4

hi, i have a seat arosa with similar engine, how do i get that blow off sound? can you link me something bro: D

@CarRemap

2 жыл бұрын

Hi, i did nothing special to the intake, except use a bigger intake pipe from outside to the airbox and remove the maf sensor. I guess the vnt of this 1752vrk with the light, billet compressor and ball bearing makes it spool at low rpm and chokes it which makes it flutter.

hello where you buy your reinforced clutch please ?

@CarRemap

3 ай бұрын

Sachs performance

Where did you get the downpipe?

@CarRemap

3 ай бұрын

I made it from steel tubes

Where's the turbo from?

@CarRemap

3 ай бұрын

BMW

Turbo golf 19tdi 1752r ?

@CarRemap

3 ай бұрын

No it's a ball bearing turbo from bmw GTD1752VRK

Pressure?😮

@CarRemap

9 ай бұрын

2 bar

cool! what rpm does the turbo spool up at?

@CarRemap

2 жыл бұрын

Thanks mate! Starts to make high torque at 2000 rpm but pulls already at 1500 in high gear.

@haraldtimma8394

2 жыл бұрын

@@CarRemap that's awesome. especially for a 1.4tdi. i like how those big brakes look on the front haha

@CarRemap

2 жыл бұрын

@@haraldtimma8394 Haha I do too. The restoration and installation of the 312mm brakes is planned for next video :)

@haraldtimma8394

2 жыл бұрын

@@CarRemap id love to see that! also did your polo come with drum brakes in the rear originally?

@CarRemap

2 жыл бұрын

​@@haraldtimma8394 Sure, wouldn't be fun if I didn't have to retrofit some discs haha. I will certainly add them to the video then

Поставил данную турбину, она работает с огромным шумом слышно как врашаються подшипники вала.Шум большой очень напрягает. Огромный минус

@CarRemap

8 ай бұрын

That's true that turbo is very noisy but I personally like it a lot! And the ball bearing and this gen of turbos make them very robust

why so little power from a 1752? increasing a vb gives more horsepower

@CarRemap

Жыл бұрын

This is due to the AL injectors not flowing enough and too restrictive intake I guess

How much power it running

@CarRemap

2 жыл бұрын

6:07

@wpgarage9765

Жыл бұрын

Hy! at what degree opening do the injectors go? What turbo pressure?

What’s the top speed ?

@CarRemap

5 ай бұрын

It should be around 220-230km/h but I did not check

Cr turbo on pd engine?

@CarRemap

Жыл бұрын

turbo from 2014-2015 BMW 150-190hp with welded PD manifold

3:00 :D :D :D :D

Engine broken or no?, 😂

@CarRemap

Жыл бұрын

still going strong mate 😂

Top speed?

@luidjissj4627

Жыл бұрын

On tdi (in my opinion) we dont search the top speed The performance goes to the second et third gear on a 400m But if we have to put a number I guess between 190 and 230 easily

Is this alive

45 bar turbo 😂😂

Hey hast du das auto noch kann man mit dir irgendwie auf insta schreiben?

@CarRemap

Жыл бұрын

Hello mate, you can contact me on insta mk4.vag