I have made my own using these components. # 433mhz RF module for wireless communication, # two arduino nano, # one ultrasonic sensor to check water level in the tank, # one relay to actuate motor, # 16x2 lcd (i2c) it shows the percentage of water in the tank, # one touch sensor to turn-on motor, # rgb led to indicate water level, # two Hi-link SMPS to power both setups one in the tank and another near motor or wherever u want to place in the house.... #when i touch the surface of touch sensor motor turns-on when water level reaches 100% then motor turns-off automatically. I have been using it since last two months and its working perfectly. I also made it for my friend he is satisfied with that too
@sidd77759 ай бұрын
Is it copper wire?and what's the gage no of this copper wire?🙏🙏
@aliegebozkurt4050 Жыл бұрын
I tried it and it worked.
@surfnexplore Жыл бұрын
what about shipping cost?
@rajvigneshtn Жыл бұрын
How do we generate a hex array for a custom audio file?
@bouraouiouni81022 ай бұрын
did you find a medhod
@abhijitjoshiortho Жыл бұрын
Which gauge wires to be used?
@moinshaikh6684 Жыл бұрын
Jlc pcb shows 2s for 5 pcb, but they take 2 dollar extra from shipping amount.
@nabinkartheek9390 Жыл бұрын
If you give continious battery voltage in transmitter after the water tank is full, will it damage the transmitter or not? When you continiously press the switch, there will flow of current from the battery into the transmitter which might damage the transmitter. Please correct me if I am wrong.
@uniquedaily62622 ай бұрын
Same question, have you found the solution? And did you use this system?
@NguyenTam-zl2tk Жыл бұрын
Hi, can use vcut to separate to many boards?
@ETSolutions2 жыл бұрын
JLCPCB update it now panelization will charge more $........
@fshabeer2 жыл бұрын
Good one, I also got the same thought, but the drawback is it will ring only once 😕. Is there any way to ring continuously?
@SaiKumar_u2say4sai Жыл бұрын
You can take Musical Multi Tune Door Bell.
@user-xi4de1mr2o2 жыл бұрын
А почему скачет показание!?
@alexismavarez50522 жыл бұрын
Lo simple es bello.
@phantominception28812 жыл бұрын
how to convert audio to analog like you did for the sound effects i need the naruto justu activation code
@endlesslove39122 жыл бұрын
From ingenious 101
@DebmalyaGhoshdaredevil2k2 жыл бұрын
can I use the BMS with 18650 Battery ??
@just4electronics1012 жыл бұрын
Sure
@yerur19122 жыл бұрын
for beginers like me it is really useful and informative.
@aathifshaan66632 жыл бұрын
What is the name that clip please reply please bro
@richiesun96762 жыл бұрын
What's in that tin he keeps dipping into?
@gregd60222 жыл бұрын
goto 6:30 for the jest of it..
@abdulmuksith33912 жыл бұрын
please help to fix this Problem. Arduino: 1.8.15 (Windows 10), Board: "NodeMCU 1.0 (ESP-12E Module), 80 MHz, Flash, Disabled (new aborts on oom), Disabled, All SSL ciphers (most compatible), 32KB cache + 32KB IRAM (balanced), Use pgm_read macros for IRAM/PROGMEM, 4MB (FS:2MB OTA:~1019KB), 2, v2 Lower Memory, Disabled, None, Only Sketch, 115200" D:\Abdullah\ESP-Covid-19 project\covid_19_graphics_display\covid_19_graphics_display.ino: In function 'long int GetData(String)': covid_19_graphics_display:109:13: error: call to 'HTTPClient::begin' declared with attribute error: obsolete API, use ::begin(WiFiClient, url) 109 | http.begin(url); | ~~~~~~~~~~^~~~~ exit status 1 call to 'HTTPClient::begin' declared with attribute error: obsolete API, use ::begin(WiFiClient, url) This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences.
@bilalabbas55652 жыл бұрын
What if we use it without floating sensor? Button wires Directly in the tank?
@hastyz73252 жыл бұрын
why was I bobbing my head to this 0:20 (x2 speed)
@Surenderkumar-mc2ri2 жыл бұрын
Hello l am aman ye chimti kaha milegi jarur bataye pleas
@LomerPVP2 жыл бұрын
Hey @Just4 Electronics Is there a way I can add a sensor to activate it #J4E #@@UCyU1RKYn7BRvUzgXds522mA
@danielpeterson81093 жыл бұрын
How can I do "Hello!" with it?
@danielpeterson81093 жыл бұрын
What is the hexadecimal thing? I Don't use hexadecimal.
@osmanpasha963 жыл бұрын
This offer is no longer relevant. Panelization now costs extra, which raises the price to $22
@dindigulautomationwaterpro51453 жыл бұрын
Hi. Can you design a Pcb to me whattsapp 8610816815
@MartynDavies3 жыл бұрын
Nice form factor
@2kBofFun3 жыл бұрын
They are wronly connected. Please use ICSP pins instead of 10-13. It makes more sense and works on all Arduino boards like the Mega, DUE and Leonardo, where 10-13 are not SPI pins.
@mikeberger16883 жыл бұрын
When you order a panelized board and you want them to panelize, do you enter the single board dimensions? (and then qty of boards, plus the rows and columns). And when you want to have them assembled what panelized size do they prefer? (JLC or PCBWAY)
@benlawton54202 жыл бұрын
That's what I've done, message me back in about a week or two and I should have them by then. It does seem to have worked though as it has panelized dimensions as well as single.
@kodilewis38493 жыл бұрын
careful with jlcpcb. My bank account was hacked from using jlcpcb. They stole over 500$ from me. chances are that they are stealing your pcb designs as well. DO NOT TRUST CHINA!!!
@SumitKumar-ym5it3 жыл бұрын
What is the tape name you should use in your video and give it's link to buy it. Please🙏🙏💓
@artmaker81513 жыл бұрын
i want this project how can i contect u?
@tohtorizorro3 жыл бұрын
What are the wires used as arms in the video?
@GravityOfLife3 жыл бұрын
you don't hav 2 use boost convereter. 3.7*2 is 7.4 which is good enough for a 9volt meter. For me I used 2 laptop batteries and I never charge them for 2 years now and still going.
@dooogfella2 жыл бұрын
But the problem is you need more module for that right? You need a bms to make sure they are running and charging at the same volts. Correct me if I'm wrong.
I need helping solder hand to make a helping soldering hand 🤦🏻 I will make my own design or I’ll buy it from the stores if they sell things like this
@GoatZilla3 жыл бұрын
This isn't 9 minutes worth of information, idiot.
@titanix27173 жыл бұрын
Can u name the wire which u used.. please
@premjithg23553 жыл бұрын
If we add a switch between floating sensor wire and bell I believe we can switch off the alarm during overflow. Just a thought not tried.
@just4electronics1013 жыл бұрын
Nice idea you can try
@tinmt31313 жыл бұрын
Can you inform about, what is this wire type material used to hold the clamp? Please tell
@jpz80423 жыл бұрын
Hi It's looking good and usefull, Can you share the corel draw file for the front panel?
@laeciolopes51153 жыл бұрын
picarera...
@MrOvo12313 жыл бұрын
i would of turned it upside down so the solder did not show
@GendaijinBlog3 жыл бұрын
Thank you for the straightforward explanation. Your English is easy to understand as well. The "you're" in your title should be "your" which is the possessive form of "you." (you're = you + are)
@madanmohan59103 жыл бұрын
how to stop the alarm
@Nikodim102013 жыл бұрын
door bell switch will triggered in some condition then bell switch battery will discharge.
Пікірлер
I have made my own using these components. # 433mhz RF module for wireless communication, # two arduino nano, # one ultrasonic sensor to check water level in the tank, # one relay to actuate motor, # 16x2 lcd (i2c) it shows the percentage of water in the tank, # one touch sensor to turn-on motor, # rgb led to indicate water level, # two Hi-link SMPS to power both setups one in the tank and another near motor or wherever u want to place in the house.... #when i touch the surface of touch sensor motor turns-on when water level reaches 100% then motor turns-off automatically. I have been using it since last two months and its working perfectly. I also made it for my friend he is satisfied with that too
Is it copper wire?and what's the gage no of this copper wire?🙏🙏
I tried it and it worked.
what about shipping cost?
How do we generate a hex array for a custom audio file?
did you find a medhod
Which gauge wires to be used?
Jlc pcb shows 2s for 5 pcb, but they take 2 dollar extra from shipping amount.
If you give continious battery voltage in transmitter after the water tank is full, will it damage the transmitter or not? When you continiously press the switch, there will flow of current from the battery into the transmitter which might damage the transmitter. Please correct me if I am wrong.
Same question, have you found the solution? And did you use this system?
Hi, can use vcut to separate to many boards?
JLCPCB update it now panelization will charge more $........
Good one, I also got the same thought, but the drawback is it will ring only once 😕. Is there any way to ring continuously?
You can take Musical Multi Tune Door Bell.
А почему скачет показание!?
Lo simple es bello.
how to convert audio to analog like you did for the sound effects i need the naruto justu activation code
From ingenious 101
can I use the BMS with 18650 Battery ??
Sure
for beginers like me it is really useful and informative.
What is the name that clip please reply please bro
What's in that tin he keeps dipping into?
goto 6:30 for the jest of it..
please help to fix this Problem. Arduino: 1.8.15 (Windows 10), Board: "NodeMCU 1.0 (ESP-12E Module), 80 MHz, Flash, Disabled (new aborts on oom), Disabled, All SSL ciphers (most compatible), 32KB cache + 32KB IRAM (balanced), Use pgm_read macros for IRAM/PROGMEM, 4MB (FS:2MB OTA:~1019KB), 2, v2 Lower Memory, Disabled, None, Only Sketch, 115200" D:\Abdullah\ESP-Covid-19 project\covid_19_graphics_display\covid_19_graphics_display.ino: In function 'long int GetData(String)': covid_19_graphics_display:109:13: error: call to 'HTTPClient::begin' declared with attribute error: obsolete API, use ::begin(WiFiClient, url) 109 | http.begin(url); | ~~~~~~~~~~^~~~~ exit status 1 call to 'HTTPClient::begin' declared with attribute error: obsolete API, use ::begin(WiFiClient, url) This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences.
What if we use it without floating sensor? Button wires Directly in the tank?
why was I bobbing my head to this 0:20 (x2 speed)
Hello l am aman ye chimti kaha milegi jarur bataye pleas
Hey @Just4 Electronics Is there a way I can add a sensor to activate it #J4E #@@UCyU1RKYn7BRvUzgXds522mA
How can I do "Hello!" with it?
What is the hexadecimal thing? I Don't use hexadecimal.
This offer is no longer relevant. Panelization now costs extra, which raises the price to $22
Hi. Can you design a Pcb to me whattsapp 8610816815
Nice form factor
They are wronly connected. Please use ICSP pins instead of 10-13. It makes more sense and works on all Arduino boards like the Mega, DUE and Leonardo, where 10-13 are not SPI pins.
When you order a panelized board and you want them to panelize, do you enter the single board dimensions? (and then qty of boards, plus the rows and columns). And when you want to have them assembled what panelized size do they prefer? (JLC or PCBWAY)
That's what I've done, message me back in about a week or two and I should have them by then. It does seem to have worked though as it has panelized dimensions as well as single.
careful with jlcpcb. My bank account was hacked from using jlcpcb. They stole over 500$ from me. chances are that they are stealing your pcb designs as well. DO NOT TRUST CHINA!!!
What is the tape name you should use in your video and give it's link to buy it. Please🙏🙏💓
i want this project how can i contect u?
What are the wires used as arms in the video?
you don't hav 2 use boost convereter. 3.7*2 is 7.4 which is good enough for a 9volt meter. For me I used 2 laptop batteries and I never charge them for 2 years now and still going.
But the problem is you need more module for that right? You need a bms to make sure they are running and charging at the same volts. Correct me if I'm wrong.
Super simple and nice :)
Can you share the diagram, please [email protected]
I need helping solder hand to make a helping soldering hand 🤦🏻 I will make my own design or I’ll buy it from the stores if they sell things like this
This isn't 9 minutes worth of information, idiot.
Can u name the wire which u used.. please
If we add a switch between floating sensor wire and bell I believe we can switch off the alarm during overflow. Just a thought not tried.
Nice idea you can try
Can you inform about, what is this wire type material used to hold the clamp? Please tell
Hi It's looking good and usefull, Can you share the corel draw file for the front panel?
picarera...
i would of turned it upside down so the solder did not show
Thank you for the straightforward explanation. Your English is easy to understand as well. The "you're" in your title should be "your" which is the possessive form of "you." (you're = you + are)
how to stop the alarm
door bell switch will triggered in some condition then bell switch battery will discharge.