Where did you get your rear deck for the carolina skiff
@727allan7272 ай бұрын
I got it from Manatee Marine and they ordered it from Carolina Skiff, but I do not believe believe Carolina skiff is making them anymore?
@boss_hoggbullys5 ай бұрын
Where did u get the deck pls
@727allan7274 ай бұрын
Deck was from Carolina skiff but I’m not sure if they still sell them
@tintdr Жыл бұрын
Guy was asked how fast is it a couple times and can't answer the ??? Why???
@mo-cchannel6107 Жыл бұрын
hello good afternoon you did a good job in your carolina I want to do the same as you , how did you order the console with carolina skiff?
@TexasNEV Жыл бұрын
What is WOT on that? I'm troubleshooting an engine issue on a 14 w/ a 30 so I'm guessing whatever your top speed on a 16 w/ a 40 would be similar.
@haroldmcclellan34482 жыл бұрын
It doesn't need a bilge pump pull a plug and ride
@99christyn3 жыл бұрын
Where can I order the front and rear deck?
@davideasterling10993 жыл бұрын
Not a good video, u show nothing important
@sector76763 жыл бұрын
You said it's weight sensitive but shouldn't it be more stable than a v-hull? Generally flat bottoms are more stable..
@jcvgcrawfishy3 жыл бұрын
Jesus Christ loves you all and he died for your sins and he rose again and he’s coming back one day repent of your sins and turn to Christ
@danielarnold27843 жыл бұрын
Where did you get it??
@matthewzayas81293 жыл бұрын
Where did you purchase the hull from?
@ufozencom4 жыл бұрын
I'm sure nobody wants to hear music.
@darthvader68474 жыл бұрын
Where do I get the deck from
@mr.nickivey5374 жыл бұрын
What year is yours?
@lucabuca53674 жыл бұрын
Do you know how fast the boat can go?
@skysoutside97084 жыл бұрын
I like the set up 👍👍👍
@cubaniton744 жыл бұрын
Installing trim tabs in a Carolina Skiff J series requires drilling a hole much larger than the one needed, then filling the hole with fiberglass putty, waiting for it to cure, then drill new holes the size of your screws to install the trim tabs. The reason is because with just regular holes in the transom area below the water line, water will eventually get inside the flotation foam through the holes, but by drilling bigger holes and sealing it with epoxy first, you are creating a water tight place where water can't penetrate, as long as the screws are not longer than the epoxy plug.
@cubaniton744 жыл бұрын
Avoid drilling holes in the floor of your Carolina Skiff, if using 3M 5200, just use a little bit more, that way you will not have to use screws, because screws will eventually allow water to penetrate into the flotation foam in the floor and the water will be trapped in there permanently, causing your boat to weight considerably more.
@AubreyM.Adventures24 жыл бұрын
Did you make that bilge area yourself, or did come that way
@ericfabian67304 жыл бұрын
hi super video. how much did you adjust the anti-cavitation plate in relation to the bottom of the hull? Thancks u
@thomasearl97324 жыл бұрын
I don't think a bilge pump is necessary it is no water gets in my Carolina Skiff unless it rains and I don't go out in the rain
@cubaniton744 жыл бұрын
Thank you for the DIY video. I did remove some material off my rear deck, but used hand tool only, a rounded file, and kept testing time after time, so avoid removing too much material, it ended up looking nice, thanks to your inspirational video. God bless you.
@TattedSails5 жыл бұрын
Where did you buy the rear deck from? Is there a website?
@cubaniton744 жыл бұрын
Look for local Carolina Skiff dealers, they might have one available.
@davidwarner67555 жыл бұрын
Cant hear you very well
@ahunterstail10835 жыл бұрын
you should get all your tools set out before filming or edit it before uploading, too drawn out, was getting boring, sorry mate, just my opinion
@MrLash735 жыл бұрын
what year is your j16 cuz mine doesn't have that little dropped indention in the back in the Middle where your bilge pump is
@cubaniton744 жыл бұрын
That's how Carolina Skiff is building their skiffs now, with a channel or tunnel to run the wiring for the console. I actually prefer the old way, because in the new system I can't see how well sealed that channel or tunnel is, and if water gets in there, it could penetrate into the flotation foam and be trapped in it.
@hungnmiami5 жыл бұрын
Please tell me when sanding what grit do you start with I have an assortment and I'm not sure how heavy to start and how like to end up thank you in advance for your help
@727allan7275 жыл бұрын
i actually used a ....1/4 in. x 1 in. Cylindrical Solid Carbide Burr Rotary File Bit with 1/4 in. Shank ...they also come in a set and they are very useful !
@bobby0506065 жыл бұрын
@@727allan727 where did you source the back decks and front deck from?
@cubaniton744 жыл бұрын
@@bobby050606 Look for local Carolina Skiff dealers, they might have one available.
@cubaniton744 жыл бұрын
@ReelNauti-Cal I did remove some material off my rear deck, but I used hand tool only, a rounded file, and kept testing time after time, to avoid removing too much material, it ended up looking nice, thanks to Allans' inspirational video. God bless you.
@lesliebyrd30025 жыл бұрын
Good job Dude. Nice build. Let's go! Your boat or mine!
@jjohn89895 жыл бұрын
Why have a switch for fish finder, if you have to power up anyway?
@kirkshammett946 жыл бұрын
What size motor is it?
@727allan7275 жыл бұрын
2016 40hp mercury
@alexriveros29606 жыл бұрын
Where did you buy the back deck ?
@cubaniton744 жыл бұрын
Look for local Carolina Skiff dealers, they might have one available.
@aidandanner25946 жыл бұрын
Not sure if your still monitoring this video but where did you order your console?
@727allan7276 жыл бұрын
i got it at manatee marine in Sarasota fl.
@kirkshammett946 жыл бұрын
I’m wanting to buy this boat how well does it do nearshore? And in somewhat rough chop?
@727allan7276 жыл бұрын
last weekend i was out in 1-2 ft chop and it was fine you just have to know slow down cant open throttle it all the time, i also had a few yachts go by and they were throwing a 4-5 foot wave... not bad at all
@1shawnv16 жыл бұрын
My seal at the edge where the deck meets the boat is older and coming off pretty bad, do you have any recommendations on what to use after I clean all the old stuff off? Thanks in advance for any advice!
@cubaniton744 жыл бұрын
Remove any material that does not feel solid, and rebuild it with layers of fiberglass and epoxy, then finish the last layer with Gelcoat.
@nicholaslangford27776 жыл бұрын
love watching your vids could you watch one of mine
@Pokemonballers876 жыл бұрын
What do you use to refinish that if it gets scratched I have some on my Seats id like to fix..
@cubaniton744 жыл бұрын
Use Gelcoat.
@Astralpilot2.06 жыл бұрын
iam buying one , it will be my first boat. Florida weather changes by the second so if they are that bad in chop whats the sense in owning one
@Wicked.Z063 жыл бұрын
Well this boat isn’t meant to take off at Jupiter. Keep it in your lakes, canal systems, mangroves, glades, etc.
@Astralpilot2.03 жыл бұрын
I bought and sold it already
@matthewduncan54196 жыл бұрын
Dude listening to you talk is like listening to an old lady taking a fucking shit you have no business making a video Jesus Christ!!!!
@colbywhite54226 жыл бұрын
How fast dose it run?
@jordancanales46 жыл бұрын
Sweet j16.... saw the vape in there lol.
@edwardsmith52347 жыл бұрын
Hey AG, nice boat. Adjust the smart tabs move it to 1 and go up till you find the spot, and it will correct the spray at transom. I have mine on one, but I have trolling motor and battery up front. So it just depends on how your boat is loaded with what you have to set it to. I have a Jv 17 cc with the Merc 40 HP. Mine is wet too. I'm up in Crystal River so shallow water here. Great little boats. Hope you enjoy it.
@chuckchamplin66277 жыл бұрын
MR.Allan I like the way u fixed your skiff very good job.my wife retires in three yrs and i get a new boat yay.and i really want a 17ft Carolina skiff.God luck with your BOAT.later CHUCK
@brettlund22557 жыл бұрын
I've got the same J16 but tiller steer with a 40 mercury 2 stroke. The lil boat is tough yes wet riding but smart tabs and a learning your trim will stop most of the splash. On the take off trim the motor up a lil and as the bow rises start trimming it down.
@steveenglish76116 жыл бұрын
Brett Lund hey man what size prop are you running on your motor?
@darkerbrother17 жыл бұрын
Do you know how fast you were going ? At what speed did you feel the drag ?
@727allan7277 жыл бұрын
i am not sure i will have to go out again and figure it out ..... i have stx automatic trim tabs on it also not sure if that part of the big splashing
@tome99007 жыл бұрын
It kinda looks like you got a lot of drag by your cavitation plate with lol that spray by the motor
@727allan7277 жыл бұрын
yea im not sure what i can do with that .....maybe move the motor higher ?? any suggestions ?
@tome99006 жыл бұрын
Allans Garage sorry for the long reply but yes if you raise the motor slightly it won’t drag as much and you’ll get more speed
@tome99007 жыл бұрын
For the center console
@tome99007 жыл бұрын
You should get a grab rail! That would complete the boat!
@sebastianmata8038 Жыл бұрын
Completely ruin*
@manch0vy5437 жыл бұрын
What size console did you purchase?
@727allan7277 жыл бұрын
the console is the small center console for J16 from Carolina skiff
@727allan7277 жыл бұрын
caught a break at the end but you can see how wet the windshield is
Пікірлер
Where did you get your rear deck for the carolina skiff
I got it from Manatee Marine and they ordered it from Carolina Skiff, but I do not believe believe Carolina skiff is making them anymore?
Where did u get the deck pls
Deck was from Carolina skiff but I’m not sure if they still sell them
Guy was asked how fast is it a couple times and can't answer the ??? Why???
hello good afternoon you did a good job in your carolina I want to do the same as you , how did you order the console with carolina skiff?
What is WOT on that? I'm troubleshooting an engine issue on a 14 w/ a 30 so I'm guessing whatever your top speed on a 16 w/ a 40 would be similar.
It doesn't need a bilge pump pull a plug and ride
Where can I order the front and rear deck?
Not a good video, u show nothing important
You said it's weight sensitive but shouldn't it be more stable than a v-hull? Generally flat bottoms are more stable..
Jesus Christ loves you all and he died for your sins and he rose again and he’s coming back one day repent of your sins and turn to Christ
Where did you get it??
Where did you purchase the hull from?
I'm sure nobody wants to hear music.
Where do I get the deck from
What year is yours?
Do you know how fast the boat can go?
I like the set up 👍👍👍
Installing trim tabs in a Carolina Skiff J series requires drilling a hole much larger than the one needed, then filling the hole with fiberglass putty, waiting for it to cure, then drill new holes the size of your screws to install the trim tabs. The reason is because with just regular holes in the transom area below the water line, water will eventually get inside the flotation foam through the holes, but by drilling bigger holes and sealing it with epoxy first, you are creating a water tight place where water can't penetrate, as long as the screws are not longer than the epoxy plug.
Avoid drilling holes in the floor of your Carolina Skiff, if using 3M 5200, just use a little bit more, that way you will not have to use screws, because screws will eventually allow water to penetrate into the flotation foam in the floor and the water will be trapped in there permanently, causing your boat to weight considerably more.
Did you make that bilge area yourself, or did come that way
hi super video. how much did you adjust the anti-cavitation plate in relation to the bottom of the hull? Thancks u
I don't think a bilge pump is necessary it is no water gets in my Carolina Skiff unless it rains and I don't go out in the rain
Thank you for the DIY video. I did remove some material off my rear deck, but used hand tool only, a rounded file, and kept testing time after time, so avoid removing too much material, it ended up looking nice, thanks to your inspirational video. God bless you.
Where did you buy the rear deck from? Is there a website?
Look for local Carolina Skiff dealers, they might have one available.
Cant hear you very well
you should get all your tools set out before filming or edit it before uploading, too drawn out, was getting boring, sorry mate, just my opinion
what year is your j16 cuz mine doesn't have that little dropped indention in the back in the Middle where your bilge pump is
That's how Carolina Skiff is building their skiffs now, with a channel or tunnel to run the wiring for the console. I actually prefer the old way, because in the new system I can't see how well sealed that channel or tunnel is, and if water gets in there, it could penetrate into the flotation foam and be trapped in it.
Please tell me when sanding what grit do you start with I have an assortment and I'm not sure how heavy to start and how like to end up thank you in advance for your help
i actually used a ....1/4 in. x 1 in. Cylindrical Solid Carbide Burr Rotary File Bit with 1/4 in. Shank ...they also come in a set and they are very useful !
@@727allan727 where did you source the back decks and front deck from?
@@bobby050606 Look for local Carolina Skiff dealers, they might have one available.
@ReelNauti-Cal I did remove some material off my rear deck, but I used hand tool only, a rounded file, and kept testing time after time, to avoid removing too much material, it ended up looking nice, thanks to Allans' inspirational video. God bless you.
Good job Dude. Nice build. Let's go! Your boat or mine!
Why have a switch for fish finder, if you have to power up anyway?
What size motor is it?
2016 40hp mercury
Where did you buy the back deck ?
Look for local Carolina Skiff dealers, they might have one available.
Not sure if your still monitoring this video but where did you order your console?
i got it at manatee marine in Sarasota fl.
I’m wanting to buy this boat how well does it do nearshore? And in somewhat rough chop?
last weekend i was out in 1-2 ft chop and it was fine you just have to know slow down cant open throttle it all the time, i also had a few yachts go by and they were throwing a 4-5 foot wave... not bad at all
My seal at the edge where the deck meets the boat is older and coming off pretty bad, do you have any recommendations on what to use after I clean all the old stuff off? Thanks in advance for any advice!
Remove any material that does not feel solid, and rebuild it with layers of fiberglass and epoxy, then finish the last layer with Gelcoat.
love watching your vids could you watch one of mine
What do you use to refinish that if it gets scratched I have some on my Seats id like to fix..
Use Gelcoat.
iam buying one , it will be my first boat. Florida weather changes by the second so if they are that bad in chop whats the sense in owning one
Well this boat isn’t meant to take off at Jupiter. Keep it in your lakes, canal systems, mangroves, glades, etc.
I bought and sold it already
Dude listening to you talk is like listening to an old lady taking a fucking shit you have no business making a video Jesus Christ!!!!
How fast dose it run?
Sweet j16.... saw the vape in there lol.
Hey AG, nice boat. Adjust the smart tabs move it to 1 and go up till you find the spot, and it will correct the spray at transom. I have mine on one, but I have trolling motor and battery up front. So it just depends on how your boat is loaded with what you have to set it to. I have a Jv 17 cc with the Merc 40 HP. Mine is wet too. I'm up in Crystal River so shallow water here. Great little boats. Hope you enjoy it.
MR.Allan I like the way u fixed your skiff very good job.my wife retires in three yrs and i get a new boat yay.and i really want a 17ft Carolina skiff.God luck with your BOAT.later CHUCK
I've got the same J16 but tiller steer with a 40 mercury 2 stroke. The lil boat is tough yes wet riding but smart tabs and a learning your trim will stop most of the splash. On the take off trim the motor up a lil and as the bow rises start trimming it down.
Brett Lund hey man what size prop are you running on your motor?
Do you know how fast you were going ? At what speed did you feel the drag ?
i am not sure i will have to go out again and figure it out ..... i have stx automatic trim tabs on it also not sure if that part of the big splashing
It kinda looks like you got a lot of drag by your cavitation plate with lol that spray by the motor
yea im not sure what i can do with that .....maybe move the motor higher ?? any suggestions ?
Allans Garage sorry for the long reply but yes if you raise the motor slightly it won’t drag as much and you’ll get more speed
For the center console
You should get a grab rail! That would complete the boat!
Completely ruin*
What size console did you purchase?
the console is the small center console for J16 from Carolina skiff
caught a break at the end but you can see how wet the windshield is
How fast does she run