Пікірлер

• 
  @ariebossley25093 күн бұрын

  You need to get rid of that track bar. They are completely unnecessary with the leafspring suspension and if you look at your own video, your leaf spring doesn’t compress at all and then your shackle flexes inward.

• 
  @tsmith63153 күн бұрын

  Thank you so much. Love how you actually bring me step by step through this!! Thx

• 
  @kylefrench1395 күн бұрын

  This video saved me a ton of time. My brake lights were not working on my 92 YJ. Turns out the brake switch was only sending 5 volts to the lights when the brake was pushed, not enough to light the leds. The hazards and turns worked fine. Swapped out the brake switch and found a t connector spliced into the wire from previous owner which likely caused the drops in voltage.

• 
  @TyStyckify6 күн бұрын

  Not sure about the M1S Pro but the FX4 Pro has a 3.5 mm headphone jack so you can use In Ear Monitors (IEMs) for better music freq response and noise cancelling. Does the M1S pro use USB C or USB micro interface?

• 
  @jeffallen-yt7uk10 күн бұрын

  Awesome breakdown you rock

• 
  @kdsgarage84759 күн бұрын

  Thank you! Thanks for watching!

• 
  @bradleylang262214 күн бұрын

  You’re the fuckin man this saved me 400 bucks

• 
  @kdsgarage847513 күн бұрын

  Awesome! Thank you for watching!

• 
  @GsStyleModsAndSpecs15 күн бұрын

  Nice vette, man! I'm about to do more uploads on mine.

• 
  @kdsgarage847513 күн бұрын

  Thank you. I appreciate the comment!

• 
  @handwayne15 күн бұрын

  Thank you for sharing. Changed out the unit in my C300 with no issues following your video!

• 
  @kdsgarage847513 күн бұрын

  Awesome! Thank you for watching!

• 
  @markcotugno515616 күн бұрын

  If the bolt is lowered a half inch does that mean the car will be lowered the same amount? Also did 3 turns of the bolt equal a quarter inch difference? Thank You

• 
  @kdsgarage847516 күн бұрын

  Lowering the bolt will push the a-arm closer to the ground, raising the car. You need to turn itcounter clockwise to lower. The number of turns might be different for everyone. Depending on your setup and age of the spring, but that’s a good rule of thumb to go by to start. Also, once you lower the car, you need to drive some. It’ll drop some more as it settles and you may need to adjust.

• 
  @dvao22 күн бұрын

  Thanks! Super useful video went right away and did the procedure, now I have 8 codes... X_X

• 
  @kdsgarage847513 күн бұрын

  Thanks for watching. I'm glad it helped. Some codes you don't need to worry about. Like battery recently disconnected and AC (if you don't have ac).

• 
  @AJ-mn4dw25 күн бұрын

  This hw to video is a true lifesaver!! I just purchased my MB C300 and the driver/passenger switch broke immediately no more than 15mins after driving the vehicle of the lot. Thank goodness my dealership had no issues sourcing the part at no cost to myself. I had called MB to see about purchasing and they quoted me close to $400, NOT including labor 😱😱🤬🤬 Absolutely ridiculous!!!!! I knew it wasn't difficult to do and am looking forward to doing this myself..

• 
  @kdsgarage847513 күн бұрын

  Stealership! I appreciate the comment! Thanks for watching!

• 
  @danbrygider265426 күн бұрын

  No

• 
  @kdsgarage847513 күн бұрын

  yes!!!!!!!

• 
  @moonc4lf27 күн бұрын

  Both switches for raising the rear windows on my C class broke (the car is 4 years old and has traveled 50k km / 31k miles), the authorized service gave me an offer for €230... I bought the original part for €53 and following yours video changed it in 3 minutes. Thank you - Authorized Mercedes service THIEVES

• 
  @kdsgarage847513 күн бұрын

  Awesome! Stay away from the stealership if you can. Thanks for watching my video!

• 
  @Big_Serb27 күн бұрын

  You can leave the (silver) bezel on, just remove the complete unit from the top. Afterwards you can replace the unit without removing the bezel. Test before placing back. Bottom first.

• 
  @kdsgarage847513 күн бұрын

  Yes, you can, but removing the bezel makes it easier and less chance of breaking anything.

• 
  @femiadesanya871128 күн бұрын

  Great video. All done in less than 5mins. Didn't need the tools because my trim is black and didn't care about scratches. Table knife was all i needed.

• 
  @kdsgarage847513 күн бұрын

  Awesome! Thank you for watching!

• 
  @user-iz_pervih_rukАй бұрын

  Зачем снимать серебристую рамку? Можно снять всё целиком сразу. Зачем менять весь блок целиком, если можно поменять одну кнопку вместо сломанной.

• 
  @kdsgarage847513 күн бұрын

  Thank you for watching! I needed to translate this comment. 1. Removing the silver bezel first just makes it easier. Its best not to cut corners. Things get broken that way. 2. Why replace one button, when more than likely, the others will break soon as well. Just replace the whole unit. Its easier, and Its cheap!

• 
  @gggfishing8090Ай бұрын

  Thank you for your review. These intercoms are shit !

• 
  @kdsgarage847513 күн бұрын

  Thank you for watching. They have their + and -.

• 
  @C6nroofingАй бұрын

  Got an excited till I saw the 2

• 
  @kdsgarage847513 күн бұрын

  Yeah, that extra 30 HP makes a huge difference. For scientific purposes, when you get your 3 done, lets line em up to see how much a difference it actually makes. We can post the video here.

• 
  @jesuslandey5744Ай бұрын

  I have a 2005 corvette I want to change door speakers but the cables of my original speaker are 2 inputs and the one I want to install have 5 inputs as I can do

• 
  @kdsgarage847513 күн бұрын

  Hi there. Thanks for the comment. I would follow the speaker's install instructions. Those speakers may need a crossover.

• 
  @BuckNasty9475Ай бұрын

  Beautiful job of planning and execution. Tastefully done. Subtle!

• 
  @kdsgarage8475Ай бұрын

  Thank you very much!

• 
  @lunovallc5018Ай бұрын

  This is the only straight to the point, clearly explained video. Thank you and keep it up.

• 
  @kdsgarage8475Ай бұрын

  Thank you!

• 
  @christhamilton42Ай бұрын

  Cheers for that. Great review with no annoying background music and no bs about the product. Loved it.

• 
  @kdsgarage8475Ай бұрын

  Glad you enjoyed it

• 
  @CJR_ControlsАй бұрын

  How did you get the multicolor finished look? Looks great!

• 
  @kdsgarage8475Ай бұрын

  Thanks for the comment. It happened by mistake. The first day, the can of stain was not mixed properly and came out a bit lighter. The second day, there was about 1/3 left in the bottom of the can and most of the darker pigment was at the bottom. I had to go back and restain some of the first day's pieces to get a more even staggered look.

• 
  @rogeliohernandez5533Ай бұрын

  Hi, dumb question: are shackles the same on both rear and front leaf springs?

• 
  @kdsgarage8475Ай бұрын

  They should be……if they’re stock. You never know what changes a prior owner may have done.

• 
  @billbob9570Ай бұрын

  you needed a cam bro thats what you were looking for not 10k and not a intake tune for no reason you are a cam customer

• 
  @kdsgarage847513 күн бұрын

  I love the blower. I was smiling off my face when I drove it home from the shop. I actually laughed out loud at the night and day difference. Best 10k I ever spent. A cam would be nice as well, I love the chop, but that is a massive undertaking because, then Ill need to do a converter, and while I'm in there might as well go RPM trans and diff so I can turn it all up. Oh, and torque tube......

• 
  @BuckNasty9475Ай бұрын

  How about sharing the wheels specs?

• 
  @kdsgarage8475Ай бұрын

  You’ll find the specs here: kzread.info/dash/bejne/oaiumLKuaNDbkbw.htmlsi=PnCYD1tEF28CyNRT

• 
  @teng-yingchung7295Ай бұрын

  hello why do you need to disassemble the 4 transmission lever device at 9:56 .thanks

• 
  @kdsgarage8475Ай бұрын

  So you can move the trans and transfer case back.

• 
  @teng-yingchung7295Ай бұрын

  @@kdsgarage8475 What I mean is that if you don’t need to disassemble the transfer case, you don’t need to disassemble the 4-speed gear lever base.

• 
  @steve28849Ай бұрын

  i have 2 of these with the version 1.2 software. you don't mention the music sharing function. does yours have it? i can't get mine to work.

• 
  @kdsgarage8475Ай бұрын

  I’m not sure what version I have, but the music sharing does work.

• 
  @Birdman953Ай бұрын

  Thank you for your video and explanation. Followed your instructions and making sure of every step. Worked out perfectly! Thanks once again👍😀

• 
  @kdsgarage8475Ай бұрын

  Glad it helped!

• 
  @nicholasvalerio9232Ай бұрын

  What did you mean at 3:15 when you saw the spring release? I just tried on my c6 but maybe I didnt jack up the leaf enough to relieve the pressure on the bolt because I wasn’t able to turn it even with a wrench. I’m just scared of stripping it so im gonna leave some wd40 on it and get back to it when i have time again

• 
  @kdsgarage8475Ай бұрын

  You’ll notice when the bottom or rubber portion of the lowering bolt is no longer making contact with the A-Arm. Thus releasing all the pressure from the bolt making it easier to turn.

• 
  @nicholasvalerio9232Ай бұрын

  @@kdsgarage8475Thank you so much!

• 
  @geraldthompson2173Ай бұрын

  Nice!

• 
  @kdsgarage8475Ай бұрын

  Thanks!

• 
  @ujuiceАй бұрын

  Thanks for this replaced mine on glc 2020 🎉 took me 5 mins 😌

• 
  @kdsgarage8475Ай бұрын

  Awesome! Thank you for watching!

• 
  @davidandkarenkight7109Ай бұрын

  This was a fantastic video. I just did this myself and saved a ton of money.

• 
  @kdsgarage8475Ай бұрын

  Glad it helped!

• 
  @porterdor39Ай бұрын

  The best video thank you

• 
  @kdsgarage8475Ай бұрын

  Thank you for watching!

• 
  @edwardadourian3780Ай бұрын

  Thank you so much for the video .My question is if we can change the buttons only without replacing the whole thing ? That's what I did on my ML 350 . Thank you one more time.

• 
  @kdsgarage847513 күн бұрын

  Maybe, but its easy and cheap to replace the unit.

• 
  @billscaggsify2 ай бұрын

  Very helpful! I have used a few of your videos now to remodel my 94 YJ.

• 
  @kdsgarage8475Ай бұрын

  Awesome! Thank you for watching!

• 
  @carllally54072 ай бұрын

  Thanks-a-million . . . you just saved me a Dealer Service Repair bill! I'm still working on it, but because of your video, I feel comfortable repairing this myself.

• 
  @kdsgarage84752 ай бұрын

  Glad it helped. Good luck with the project.

• 
  @jmwap36332 ай бұрын

  Thanks man very helpful video! 💯 Actually did it without breaking anything for once haha

• 
  @kdsgarage84752 ай бұрын

  Awesome. Good work! …..and thanks for watching!

• 
  @chevysaregr82 ай бұрын

  I use 34/70 for most my beers, including light beer. Ferment at room temp at 10psi and its so clean, crisp and amazing. Way cleaner then us05 ale yeast

• 
  @kdsgarage84752 ай бұрын

  Thanks for the suggestion. I’ll give it a try. I used us05 because I had so much of it from all my ipa projects.

• 
  @Greydawg2 ай бұрын

  Feels like having enough money to live & build like this means there's none left over for a good, inexpensive microphone, but that's why I wish I could just *give him one of my microphones.* ❤

• 
  @kdsgarage84752 ай бұрын

  I agree. I've been trying to get my hands on some higher quality audio and video equipment, but cant yet justify the 5k for a decent setup. My office has good acoustics since I've added the acoustic tile wall, but lose that advantage when I'm recording elsewhere. I've found some quality used stuff on marketplace, but every time I find something, the people flake out. Please send me one if you have so many lying around.

• 
  @Greydawg2 ай бұрын

  @@kdsgarage8475 5k? In all sincerity, that's just not necessary; a new microphone, even one for a cell phone, is less than $50 (even the "best" Shure mic is $400 but not necessary to spend that much). I do video for a living & likely never $5k-worth at once.

• 
  @AfterFalls2 ай бұрын

  Do you happen to have the plans that can be shared?

• 
  @kdsgarage84752 ай бұрын

  Thanks for the comment. I downloaded the cabinet plans from the geek pub, then made some changes to the design and adjusted them to fit the scale I wanted for my project.

• 
  @2smooth2802 ай бұрын

  Did that fix your problem?

• 
  @kdsgarage84752 ай бұрын

  Yes, that fixed the motor. The cart itself had lots of other issues that needed to be addressed. Once everything was addressed, its been running great. It hits just over 25mph with this motor. It spins at about 4200 rpm.

• 
  @mikemullins88032 ай бұрын

  Thanks so much K&D. I just replaced the Window Module on my 2016 Merc C220D. One of the switches broke off and both switches for the back windows did not work. I followed your Instructions exactly and Presto - all replaced and Works Perfectly. Keep up the good work. Thanks again.

• 
  @kdsgarage84752 ай бұрын

  Hi Mike, Thanks for the comment. I happy the video was able to help.

• 
  @metin220519812 ай бұрын

  really junk that Mercedes uses. All window switches of my Mercedes C180 2021 have already broken.

• 
  @kdsgarage84752 ай бұрын

  Yep. Contract to he lowest bidder.

• 
  @metin220519812 ай бұрын

  Echt troep wat mercedes gebruikt, raam schakelaar van alle deuren is al eens kapot gegaan van mijn mercedes c180 2021

• 
  @kdsgarage84752 ай бұрын

  Thank you!

• 
  @Doberbull2 ай бұрын

  What headers do you have on the car? Also, do I need headers for the A&A kit? I only have a muffler delete currently, stock manifolds and x pipe for now

• 
  @kdsgarage84752 ай бұрын

  I have kooks long tubes, and catless x-pipe feeding magnaflo resonators. I was told by 3 tuners that the long tube headers will make a big difference with the addition of the blower. Since your forcing more air in, gotta get better exhaust flow out.

• 
  @mike060606772 ай бұрын

  I’m currently thinking about getting blower just like this for my grand sport my car is currently canned and has headers already what did this kit run you money wise I just want to get an idea of wat I would be looking at? Thanks in advance

• 
  @kdsgarage84752 ай бұрын

  10K OTD with the cooks long tubes and xpipe.

• 
  @vladimirhaxhiraj64502 ай бұрын

  Hi. Where I can find an engine+gearbox for Quadzilla rs700.? Thanks

• 
  @kdsgarage84752 ай бұрын

  I’m not sure what a RS700 is…

• 
  @vladimirhaxhiraj64502 ай бұрын

  @@kdsgarage8475 , I have many quads and buggies and my friend bring me this atv Quadzilla 700(rs) , someone still the engine+gearbox. So now I wont to ii se for my tours but need to find an engine to fix it

• 
  @kdsgarage84752 ай бұрын

  @@vladimirhaxhiraj6450 thank you for your message. I am not familiar with a 700 rs. Are you referring to a 700 raptor se?

• 
  @TT408VETTE2 ай бұрын

  Quick question; for the rear fender conversion on a base coupe to oem GS rear fender; Is ot possible to reuse any of the base wheelhouse plastic pieces? I'm trying to avoid purchasing replacement wheelhouse/fender liners if possible? Ty

• 
  @kdsgarage84752 ай бұрын

  I’m not sure. Your application is different than mine. My rear quarters came with extension pieces for the wheelhouse. You’ll also need the flares (mud flaps), which are discontinued. You can get aftermarket carbon fiber flares however.

• 
  @andrewsapp8563 ай бұрын

  Thanks for sharing. Love the zillas and the vette

• 
  @kdsgarage84753 ай бұрын

  Thank you for watching!