Пікірлер

• 
  @robertwest843613 күн бұрын

  Getting ready to do seals on an 03 Dyna super glide. Video was very helpful. Great job. Thank you.

• 
  @steelcitycaprice.899Ай бұрын

  🤛🏾😎 just put crank and bearings in my 0610r and second ride that rattle started...but it is the original oem tensioner so almost 20yrs old and bound to go bad. Gotta order one of those manual ones for sure.👍🏽🏁🏁🏁 Good post well explained.

• 
  @dwightcarlson71362 ай бұрын

  Is it necessary to remove the pan to access the drain plug? What size the drain plug 'o'ring?

• 
  @mr_Christ0pher3 ай бұрын

  Great video. I have a 21 as well with the same loud crunchy sound from 1st to 2nd shift. What causes this? I notice around 3k rpm shift practically sucks into gear but most other times I get the crunch sound.

• 
  @folerx4 ай бұрын

  is it better to have more gps speed, maybe 200kmh or is it irrelevant? OE speedometer is not linear, more speed less correct is.

• 
  @victorserna90396 ай бұрын

  Is very interesting how you do the work. Is so smart how you explain. Got an idea what my mechanic what will be do in my bike. Which is same like your.thank you sir!👍🏻👍🏻👍🏻

• 
  @Eqwi6 ай бұрын

  thanks a lot

• 
  @Vedran.7 ай бұрын

  I just use automatic chain tensioner on my Z900. When chain makes noise for more that 2000-3000km and tensioner dont do it itself (and it never did), i adjust it one click (2 small bolts loosened until one click is heard). Its like MCCT :D I did it 3-4 times in past 72500km.

• 
  @josephferris69367 ай бұрын

  my zx6r manual that i just used to do my job for my 2000 zx6r also said what his manual says.....confusion now.

• 
  @craigster12348 ай бұрын

  I didn't think this was boring at all. But then again... I do have the same car so that helps!

• 
  @stevejenks77118 ай бұрын

  Excellent series! Lots of clarity + logical sequence of steps.

• 
  @jwbonnett8 ай бұрын

  You shouldn't solder cables in any vehicle, this was a lesson learnt from the aerospace industry, due to vibrations the solder cracks and creates a break quicker.

• 
  @CebastyanB10 ай бұрын

  Thank you bro! I was struggling with replacing my rear wheel trying to get the wheel in with the caliper still in place rather than installing it last which makes complete sense

• 
  @EdTrollington11 ай бұрын

  Thanks for the video! Very informative!

• 
  @zgarmy61 Жыл бұрын

  Did it work??

• 
  @fpvtechnology837 Жыл бұрын

  Too much complicated!

• 
  @cameronsword2081 Жыл бұрын

  it seems to me to be absolute madness to loosen the tensioner while the engine is running

• 
  @user-nk2kp7un8p Жыл бұрын

  Thanks rider. B safe out there, if u r still riding. But u save me a lot of money

• 
  @mustafacaglak6044 Жыл бұрын

  Even if it's a photocopy. Thank you very much.

• 
  @Mech.E Жыл бұрын

  The fact that this diy is from 2011and so good is insane

• 
  @Mech.E Жыл бұрын

  The trick would have saved me 15 bucks two days ago 😬 but at least I got the right tool now.

• 
  @TheGreenTeaGuy Жыл бұрын

  Do you know why the starter gear with the mark only rotates when you spin the crank counter clockwise but the manual says to rotate it clockwise?

• 
  @jessefpv9217 Жыл бұрын

  Gosh This is So Confusing to me idk why.

• 
  @victorteran9766 Жыл бұрын

  Very nice! I also have a 6 MT, how do you modify for heeltoe? do you have problem with revmatching? very nice vid, and the fact that oyu were able to get the 6MT with the 8 inch screen, I am jealous mate!

• 
  @wedginator Жыл бұрын

  Thanks! I just needed to modify the gas pedal. I screwed on an extender to bring the gas pedal closer to the brake. These are some parts I bought off ebay and made them fit using aluminum pieces. This makes revmatching much easier.

• 
  @vernonz8897 Жыл бұрын

  Keep it up!!! Find out the secret > Promo>SM!!!

• 
  @michaelkulman7095 Жыл бұрын

  It's less confusing to convert liters the can holds to milliliters and then divide by 50 to get the amount of oil to add in milliliters for 50:1. So a 5 liter can equals 5,000 milliliters, (just multiply by 1,000) then divide 5,000 by by 50 equals 100 milliliters of oil to add to a 5 liter can for a 50:1 mix.

• 
  @marcvipond159 Жыл бұрын

  Great article. It's a while since I've done this on a bike and it's always good to have a reminder. Very well put together clear and concise.

• 
  @proto7688 Жыл бұрын

  excellent vid man!@ thank you

• 
  @happycanadian5424 Жыл бұрын

  Btw the timing mark is to put pistons 1 or 4 at tdc not both so make sure you’re not 360 degrees out on your measurements. You can check this by seeing if the cam lobes on pistons 1 or 4 are engaged then you can continue to measure the valve spacing.

• 
  @emmettturner9452 Жыл бұрын

  It isn’t that relays are used where you need more amperage than a switch can provide or else they would just make higher-amperage switches with the same contacts that go in a relay. No, a relay is when you need a switch that is electrically actuated instead of requiring you to physically flip/turn a switch. The reason you might think otherwise is because one of the biggest reasons to use a relay is to switch a high amp circuit on/off with a low amp circuit. For example, you don’t want all the amps from your headlights or starter going through the ignition switch, so the key on and start positions merely trigger a relay that gives fully power to the starter or headlights.

• 
  @claytonhawkins8785 Жыл бұрын

  I can't say that my 2007 ninja 650 r front sprocket nut did not cooperate like yours and is currently still being a major mother stumper . Are you sure you didn't rehearse or edit your video? Lol! It looked way to easy you should come take a crack at this one of mine lol!

• 
  @Vedran.7 ай бұрын

  Impact gun is safest (both for you and for motorcycle) way do undo that nut. I have relatively strong pneumatic impact gun (over 2000Nm - 1500 ft-lbs) and had no problem with that nut on my 2020 Z900.

• 
  @jordanwigley8909 Жыл бұрын

  Do you have to drain the oil and take bolt out to look in the side windows to see tdc

• 
  @tjratz1 Жыл бұрын

  Thank you for this video! Will this work the same for the new k110s?

• 
  @deathgod79252 жыл бұрын

  I watch all your videos such a huge help I fallow. Ur steps omg bro ur a pro hit me up I wanna show u my project zx6r 2007 boreded

• 
  @2WCapo2 жыл бұрын

  Using this video to double check my work on my 2021 ZX6R. At 15k miles I am seeing tight clearances on all of my exhaust valves, and within spec of all of my intake valves. Thank you again for posting this video it is very helpful 11 years later.

• 
  @motoridesaz37292 жыл бұрын

  Hey man great video but what if I moved my Adjusters when taking off the tire on accident how would I get them back to where they were

• 
  @prototype99042 жыл бұрын

  AWESOME M8 Thanks \m/

• 
  @zmanphx2 жыл бұрын

  Daisy chain tx to rx to tx to rx

• 
  @rohlen62152 жыл бұрын

  Great tips. I just got a 2009 Ninja 500R. It hasn’t been run in a few years, so I’m taking one issue at a time. I have it started but no headlight. The bulb is good, the connector is good, the ground is fine and the hi / low switch seems fine. When I turn the key all the other lights come on but no headlight. Any suggestions would be greatly appreciated.

• 
  @HighGrade_FireBlade2 жыл бұрын

  The reason all modern sport bikes have cam chain noise is because that’s how they’re designed. My uncle just retired as a senior mechanical engineer at Honda and he was explaining to me that over the years they discovered a direct relationship between the strength of the tensioner and cam chain components (guides, chain, sprockets). Through research they found that they could greatly reduce the amount of wear to the timing components by using a less powerful tensioner. Does this mean more noise and a unit that wears out faster, yeah, but it also means much more longevity for the engine.

• 
  @kritterdangus31022 жыл бұрын

  Please stay in Canada. 😜

• 
  @bongoms2 жыл бұрын

  need to do the adjustment on my 04 636 and this video has been a live saver lol, thanks internet man from 11 years ago

• 
  @ohlukkyman2 жыл бұрын

  I know you can damage the motor if not enough oil gets into the fuel mix. What if you accidentally put too MUCH oil in the mix? Is there a downside, other than dirtier exhaust?

• 
  @bryantreeves6044 Жыл бұрын

  you will foul a spark plug and need to clean or replace it

• 
  @kalkurap2 жыл бұрын

  I have a JR radio that takes external modules. I am hoping that if I use the iRangeX Plus module in the external bay, your method of setting it up would still work. If you have any thoughts on this, please comment. Thanks for the video, really helpful.

• 
  @BELINC72 жыл бұрын

  I NEED TO FIND AN AMERICAN WHO USES OUNCES AND PINTS/GALLONS

• 
  @32marcopolo2 жыл бұрын

  Apple 15.02

• 
  @k9millie12 жыл бұрын

  Hey brother what kind of nut socket did you get. Is it the normal square or a special one . And by the way I need it for a 2009 one. I seen newer models that use the regular socket but this one seems to have like a star one .

• 
  @dougmaverick32872 жыл бұрын

  Would be easier to make 5 litres total, then you would add 100ml of 2 stroke oil.

• 
  @kevinmiller71052 жыл бұрын

  take a shit everytime he says umm. You will be wasted 😁😁

• 
  @kevinmiller71052 жыл бұрын

  shot*^

• 
  @wiitrujillo2 жыл бұрын

  You’re awesome man! Just so you know, till this day, people are still watching your videos and they are extremely helpful! My 2016 zx6r appreciates you a ton!