The follow tool doesn’t work… absolutely hate Schlage
@DrL33productions18 күн бұрын
This dude just saved my butt! Thank you 👏🏾👏🏾🙌🏾🙌🏾
@gerardfricot300918 күн бұрын
Can they be rekeyed if you don’t have a key?
@SlightlyStevenАй бұрын
Would the lock still work without the Retaining pin?
@KDrop84Ай бұрын
Everything fell out 😭
@skyghАй бұрын
What isn't shown are the springs and tops pins the follower keeps in place that line up over each pin chamber in the plug. If the follower is pulled out these parts will escape and will need to be replaced one at a time with tweezers. Do not let the follower come out without the plug to take it's place or you will be unhappy
@janaEXTREMEАй бұрын
Off to Home Depot I go to attempt to rekey our 2 deadbolts. This video was great and gave me the confidence to do it myself.
@GregoryGuay2 ай бұрын
Suddenly, my keypad is not working yet my Apple HomeKit Bluetooth connection works fine. I put new batteries in it, but the keypad is still not working. Now it does a single beep. When I try to do a factory reset, by removing the batteries and then reconnecting while holding down the Schlage button,it continues with the single beep and double green checkmark blink. This video says it’s supposed to blink three times but this is not the case.
@novalkel2 ай бұрын
Great job thanks
@l310073 ай бұрын
Where do you get a new key to rekey your locks to?
@mmc818212 ай бұрын
I have the same question 😅
@paulfasse80323 ай бұрын
Great informative presentation. You spoke in very easy to understand instructions. Thank you
@wuptydo73 ай бұрын
hi so I have used this video to attempt to rekey locks about 6 times. 2 of those times I followed this video and jammed the cylinder. The other 4 I did not listen to the video at all key step and it made all the difference. The problem arises when I am sliding the cylinder back on to the housing. If you slide it above those mini half holes and then try to turn the key, the pins get stuck in the half hole and you’ve completely jammed your cylinder. Instead, I slid the cylinder on the other side, without the mini holes, then just manually turned them back to the proper full holes. Has anyone else run into this issue? Am I doing something wrong or is this video incorrect?
@MartinTessmer3 ай бұрын
This procedure was very helpful. Here's a few tips that might make it even easier to complete: 1) The "factory preset codes" are the 4-digit user codes, not the longer programming code. 2) When it comes time for you to enter the 4 digit user code (after you've reset the lock), press the outside Schlage button and RELEASE it. Wait for the screen to light up, then press in one of the two four-digit user codes, making sure that you see a green check mark after you press in each number.
@rkb91554 ай бұрын
Thank you so much for a fantastic video! You are a gifted instructor.
@ronihughes67714 ай бұрын
Where do i buy the keying kit?
@pazziefsu4 ай бұрын
Life saver video. This helped me out so much!
@redneck0485 ай бұрын
Thank you, you just answered all my questions.
@JohnnyNubs6 ай бұрын
anyway to do this with out the original key? I have 4 dead bolts on one of my buildings that I lost the keys too but i have another main Schlage key id like to rekey them too so all my locks will be one key. i love schlage and just figure i need to buy new ones.
@MrMannyboy3296 ай бұрын
Excellent video, thanks.
@mrponce23896 ай бұрын
Is it possible to rekey a double key deadbolt?
@cherylpluto83156 ай бұрын
All the pins fell out thanks to my following the instructions on the back out the rekey kit. How do I replace them?
@morgan793476 ай бұрын
I have tried to find 4 sets of Schlage locks door & deadbolt all keyed the same as I lost my keys. I have one Schlage lock set on a door I recently replaced. So for the other 3 I’m going to get sets or individuals & rekey them. This looks like the cats meow.
@jimsutton44566 ай бұрын
A quick question I couldn’t find an answer to on the Schlage website. I am hoping to rekey a Schlage encode, smart deadbolt and a Schlage B 60N deadbolt to use this same key. Is the five pin cylinder on the Encode deadbolt the same or similar to the five pin cylinder used in the B60N deadbolt? Would they use the same pins if I bought a rekey kit online to rekey these cylinders? A vendor on eBay is telling me they use different pins, but he doesn’t sound that sure of himself. Many thanks for your help. Q2: Can a 6-pin key be used with a 5-pin lock?
@metalfabman54777 ай бұрын
Excellent tutorial! thank you for making this video all I need now is the schlage rekey kit thanks again
@ronihughes67714 ай бұрын
Where did you buy the keying kit?
@apostoloskoritas91497 ай бұрын
Really nice clean and clear videos.Thank you for sharing
@taos557 ай бұрын
Great demonstration on how to perform this task with such clear tutorial. Very appreciated!
@billschmitt72738 ай бұрын
10 minutes of commercials. I figured it out myself before the commercials were fininshed.
@user-rx8hx4wv1u8 ай бұрын
Wonderfully useful explanation. Thank you!
@choco.es.unlimited8 ай бұрын
What a mission
@yordanpopov9 ай бұрын
Liver?
@JSpade8510 ай бұрын
How do you remove the core without having the key to rotate the cylinder?
@devastatoraudio4 ай бұрын
Has to be picked, I bought a cheap picking kit from ebay, still cheaper then paying a locksmith
@piaroger858211 ай бұрын
I’m only getting two green checks
@HarrisonK11 ай бұрын
Thank you! Very easy to understand
@cpg800011 ай бұрын
Phenomenal instruction and clear demonstration. You just gave me the confidence to re-key three of my deadbolts. Many thanks, and best regards.
@ronaldupchurch975211 ай бұрын
This is the second home in which kzread.infoUgkx0jZ_lGlDVJhDnmagEU8gn47cmfPNlLQU we've replaced our "regular" doorbell with a Ring video doorbell and we really enjoy it. It is very easy to install and it works very well, with a clear picture through the app and good in-home use (we added the chime, which is also easy to install and doesn't require another thought to use).
@evictor99 Жыл бұрын
Exellent instructions
@ChrisMedici Жыл бұрын
Thank you!
@Dicofol1 Жыл бұрын
What kind of lubricant if any would you recommend for a deadbolt ?
@11145131 Жыл бұрын
Well done.
@kitemonger Жыл бұрын
Can you change the code to open the lock?
@suspicionofdeceit Жыл бұрын
How do I Get the removable cap on? Is there a specific technique?
@kittyreincat Жыл бұрын
Thank you so much!! I was having difficulty with my lock after changing the batteries. Your video was much more descriptive than the user manual. My lock now works and I am able to leave my house.
@Hodor59 Жыл бұрын
Low key one of the best tutorial videos I’ve ever seen. Can’t believe I was gonna pay someone to do this.
@yosh_lopez Жыл бұрын
I revisit this video annually when I have to change my parent’s lock. Thank you
@joy4moi Жыл бұрын
Excellent and informative video. I did not understand how it would be possible to rekey a lock, but now I understand how it's done! Thank you.
@follyroger Жыл бұрын
Excellent video! I've used my relay kit several times in the past with very frustrating results. I found this video this time around and it couldn't have been easier.
@utubs100 Жыл бұрын
Thank you!
@Windycity773 Жыл бұрын
What if it don’t want to open after u enter or scan your id
@janicewheeler52865 ай бұрын
kzread.info/dash/bejne/hmagxZJ8Ydyyg5c.html
@learnjcbskidsterchickensga7594 Жыл бұрын
Mines a different model and I take the one screw out and I can’t get the cover out
Пікірлер
The follow tool doesn’t work… absolutely hate Schlage
This dude just saved my butt! Thank you 👏🏾👏🏾🙌🏾🙌🏾
Can they be rekeyed if you don’t have a key?
Would the lock still work without the Retaining pin?
Everything fell out 😭
What isn't shown are the springs and tops pins the follower keeps in place that line up over each pin chamber in the plug. If the follower is pulled out these parts will escape and will need to be replaced one at a time with tweezers. Do not let the follower come out without the plug to take it's place or you will be unhappy
Off to Home Depot I go to attempt to rekey our 2 deadbolts. This video was great and gave me the confidence to do it myself.
Suddenly, my keypad is not working yet my Apple HomeKit Bluetooth connection works fine. I put new batteries in it, but the keypad is still not working. Now it does a single beep. When I try to do a factory reset, by removing the batteries and then reconnecting while holding down the Schlage button,it continues with the single beep and double green checkmark blink. This video says it’s supposed to blink three times but this is not the case.
Great job thanks
Where do you get a new key to rekey your locks to?
I have the same question 😅
Great informative presentation. You spoke in very easy to understand instructions. Thank you
hi so I have used this video to attempt to rekey locks about 6 times. 2 of those times I followed this video and jammed the cylinder. The other 4 I did not listen to the video at all key step and it made all the difference. The problem arises when I am sliding the cylinder back on to the housing. If you slide it above those mini half holes and then try to turn the key, the pins get stuck in the half hole and you’ve completely jammed your cylinder. Instead, I slid the cylinder on the other side, without the mini holes, then just manually turned them back to the proper full holes. Has anyone else run into this issue? Am I doing something wrong or is this video incorrect?
This procedure was very helpful. Here's a few tips that might make it even easier to complete: 1) The "factory preset codes" are the 4-digit user codes, not the longer programming code. 2) When it comes time for you to enter the 4 digit user code (after you've reset the lock), press the outside Schlage button and RELEASE it. Wait for the screen to light up, then press in one of the two four-digit user codes, making sure that you see a green check mark after you press in each number.
Thank you so much for a fantastic video! You are a gifted instructor.
Where do i buy the keying kit?
Life saver video. This helped me out so much!
Thank you, you just answered all my questions.
anyway to do this with out the original key? I have 4 dead bolts on one of my buildings that I lost the keys too but i have another main Schlage key id like to rekey them too so all my locks will be one key. i love schlage and just figure i need to buy new ones.
Excellent video, thanks.
Is it possible to rekey a double key deadbolt?
All the pins fell out thanks to my following the instructions on the back out the rekey kit. How do I replace them?
I have tried to find 4 sets of Schlage locks door & deadbolt all keyed the same as I lost my keys. I have one Schlage lock set on a door I recently replaced. So for the other 3 I’m going to get sets or individuals & rekey them. This looks like the cats meow.
A quick question I couldn’t find an answer to on the Schlage website. I am hoping to rekey a Schlage encode, smart deadbolt and a Schlage B 60N deadbolt to use this same key. Is the five pin cylinder on the Encode deadbolt the same or similar to the five pin cylinder used in the B60N deadbolt? Would they use the same pins if I bought a rekey kit online to rekey these cylinders? A vendor on eBay is telling me they use different pins, but he doesn’t sound that sure of himself. Many thanks for your help. Q2: Can a 6-pin key be used with a 5-pin lock?
Excellent tutorial! thank you for making this video all I need now is the schlage rekey kit thanks again
Where did you buy the keying kit?
Really nice clean and clear videos.Thank you for sharing
Great demonstration on how to perform this task with such clear tutorial. Very appreciated!
10 minutes of commercials. I figured it out myself before the commercials were fininshed.
Wonderfully useful explanation. Thank you!
What a mission
Liver?
How do you remove the core without having the key to rotate the cylinder?
Has to be picked, I bought a cheap picking kit from ebay, still cheaper then paying a locksmith
I’m only getting two green checks
Thank you! Very easy to understand
Phenomenal instruction and clear demonstration. You just gave me the confidence to re-key three of my deadbolts. Many thanks, and best regards.
This is the second home in which kzread.infoUgkx0jZ_lGlDVJhDnmagEU8gn47cmfPNlLQU we've replaced our "regular" doorbell with a Ring video doorbell and we really enjoy it. It is very easy to install and it works very well, with a clear picture through the app and good in-home use (we added the chime, which is also easy to install and doesn't require another thought to use).
Exellent instructions
Thank you!
What kind of lubricant if any would you recommend for a deadbolt ?
Well done.
Can you change the code to open the lock?
How do I Get the removable cap on? Is there a specific technique?
Thank you so much!! I was having difficulty with my lock after changing the batteries. Your video was much more descriptive than the user manual. My lock now works and I am able to leave my house.
Low key one of the best tutorial videos I’ve ever seen. Can’t believe I was gonna pay someone to do this.
I revisit this video annually when I have to change my parent’s lock. Thank you
Excellent and informative video. I did not understand how it would be possible to rekey a lock, but now I understand how it's done! Thank you.
Excellent video! I've used my relay kit several times in the past with very frustrating results. I found this video this time around and it couldn't have been easier.
Thank you!
What if it don’t want to open after u enter or scan your id
kzread.info/dash/bejne/hmagxZJ8Ydyyg5c.html
Mines a different model and I take the one screw out and I can’t get the cover out
Thank you very much for sharing your expertise.