Grabe yung motor, may part na parang nagwawala sa lakas 😅
@Violator-RC2 күн бұрын
@@johnpaulpunla3357 nadaan sa 3s bro.
@Violator-RC2 күн бұрын
@@johnpaulpunla3357 may full run ako sa fb limited ksi yung dito sa yt shorts.
@kyusha51223 күн бұрын
is the stock mn82 waterproof ready? or do we have to purchase a certain part to make it waterproof?
@Violator-RC3 күн бұрын
@@kyusha5122 you have to use nail polish on the electronics ro make it water resistant.
@kyusha51223 күн бұрын
@@Violator-RC ohh ok ok do i need to extend the antenna from the circuit board? or just put a nail polish too on that short antenna?
@Violator-RC2 күн бұрын
@@kyusha5122 no need for the antenna.
@kyusha51222 күн бұрын
@@Violator-RC ohh ok... coz i saw a post about the mn82 getting submerged under the water and the rc stopped working although the board is waterproof it says the antenna is too short and its way under the water and stops working but after removing it from the water it works again
@Violator-RC2 күн бұрын
@@kyusha5122 If the antenna is submerged underwater then the signal is going to drop. I thought you meant putting nail polish on the antenna :D
@raybradleyladi2674 күн бұрын
cars in offroad outlaws be like when you install a snorkle:
@Violator-RC4 күн бұрын
pretty much.
@BrodieChristophers6 күн бұрын
Love the vid what thicknesses the styrene?
@Violator-RC6 күн бұрын
Thank you. I used 1mm thickness then put them together to create a 4mm thick walls and support.
@TokyoNightGirl-fk4cn8 күн бұрын
💞Wow💞💜💜💜💜💜💜💜💛
@Violator-RC8 күн бұрын
Thank you so much!
@danielg.whjwjwjw554113 күн бұрын
Oi gente, sou do Brasil 🇧🇷 ! meu sonho é uma dessas eu sou apaixonado, só que aqui tá muito caro, vcs não poderiam me enviar uma de presente?
@guilhermepassos893017 күн бұрын
qual o tamnaho desses amortecedores ? manda o link de onde comprou
if you're planning on using the stock bed you might have to trim since this is too long for mn82. I just used this to cater to the canopy weight.I also made a custom shock towers for it.
@guilhermepassos893016 күн бұрын
Entendi, muito obrigado.
@Violator-RC16 күн бұрын
@@guilhermepassos8930 you're welcome.
@MNRc-crawler21 күн бұрын
I'm currently making something like this to but I'm using PVC pipe that got flatten
@Violator-RC21 күн бұрын
That's nice. PVC is very durable. I hope I see your setup soon.
@Violator-RC21 күн бұрын
I have a new project right now, I'm replicating the maverick viper 16 camper trailer
@MNRc-crawler20 күн бұрын
@@Violator-RC cool
@MNRc-crawler20 күн бұрын
@@Violator-RC sure i will appload some short video of it when I'm done ❤️❤️
@Violator-RC20 күн бұрын
@@MNRc-crawler awesome. Tag me up!
@mickeysrccrawl22 күн бұрын
Nice build. ✌😎 what glue do you use? Best from Denmark
@Violator-RC22 күн бұрын
@@mickeysrccrawlThanks. I used oily super glue.
@mickeysrccrawl22 күн бұрын
@@Violator-RC year, but can read the green label
@Violator-RC21 күн бұрын
@@mickeysrccrawl it's a Chinese brand and the only English on it says oily glue.
@Violator-RC21 күн бұрын
@@mickeysrccrawl Tree Frog Oily Glue,Welding High-Streth Oily Glue,Repair Glue for Electrical,Electronic,Craft,Rock,Glass,Plastic,Toy-1.8oz a.co/d/0cEyuaaP kinda like this but mines Chinese
@mickeysrccrawl21 күн бұрын
@@Violator-RC thanks :-)
@Rs-fg1rz28 күн бұрын
I'm a bit in a situation, should I buy MN99s, Mn78, Mn82, or Wpl C24? great video btw!
@Violator-RC28 күн бұрын
Thank you. I'd recommend to go for the MN82 but the 99 and 78 are great as well.
@Rs-fg1rz28 күн бұрын
@@Violator-RC Thank you!
@Violator-RC28 күн бұрын
@@Rs-fg1rz Welcome.
@thecomedyhouse12329 күн бұрын
On the receiver module , there is 6 pin plug is empty any idea whats that for ?
@Violator-RC29 күн бұрын
@@thecomedyhouse123 I think that's for the light kit but I'm not really sure.
@oyemstvofficialАй бұрын
anong tawag po ba nong tube? o may link po kayo sa shoppe?
@Violator-RCАй бұрын
@@oyemstvofficial s.shopee.ph/3fioWVjAKA Yung NASA video 4mm sukat nyan.
@oyemstvofficialАй бұрын
@@Violator-RC thanks po
@Violator-RCАй бұрын
@@oyemstvofficial welcome.
@oyemstvofficialАй бұрын
isa pa po hehehe, yung sheets ilang mm po, nahihirapan ako pag pvc, mas maganda yung gamit nyo at cutter lang pwede na
@Violator-RCАй бұрын
@@oyemstvofficial 1mm yung kapal Ng styrene sheet na gonagamit ko. Makapal pag PVC Kasi Kaya mas mahirap yun
@johnpaulpunla3357Ай бұрын
Nice, hindi mona kailangan umorder sa shopee hehe
@Violator-RCАй бұрын
@@johnpaulpunla3357 oo nga laking tipid enjoy pa hehehe.
@ARJAYBuenoАй бұрын
I just one of this just waiting to arrive❤
@Violator-RCАй бұрын
You're going to love this one.
@sciptofanicАй бұрын
Loved the work! great video. Very inspiring. #Respect
@Violator-RCАй бұрын
Thank you so much. I really appreciate it.
@s3th_editz742Ай бұрын
how did you cut the styrene?
@Violator-RCАй бұрын
I used a box cutter.
@s3th_editz742Ай бұрын
@@Violator-RC thank you so much
@Violator-RCАй бұрын
@@s3th_editz742 you're welcome.
@SNKCreativityАй бұрын
отличная модель, купил себе тоже такую!
@Violator-RCАй бұрын
Nice. This is an awesome trail truck with lots of after market support.
@gustavoaraujo6278Ай бұрын
Comprei também, estou aguardando chegar 🇧🇷
@Violator-RCАй бұрын
@@gustavoaraujo6278 It's worth the wait.
@danielg.whjwjwjw554113 күн бұрын
Oi gente, sou do Brasil 🇧🇷 ! meu sonho é uma dessas eu sou apaixonado, só que aqui tá muito caro, vcs não poderiam me enviar uma de presente?
@s3th_editz742Ай бұрын
is it waterproof? if it is how did you do it?
@Violator-RCАй бұрын
It is waterproof, I'm using a cheap 60a esc on this one which is waterproofed already then I waterproofed the dumborc receiver using nail polish then wrapped a breathable fabric on the 370 motor so the water that comes inside the motor will be filtered.
@s3th_editz742Ай бұрын
@@Violator-RC thank you
@Violator-RCАй бұрын
@@s3th_editz742 no worries.
@vhonborbon986Ай бұрын
Where do you buy the plastic materials?
@Violator-RCАй бұрын
Ordered styrene from our local shopping app here in PH.
@vhonborbon986Ай бұрын
Hey man what materials did you use?
@Violator-RCАй бұрын
Styrene.
@jandymckracken6797Ай бұрын
Can you tell me where to get the wheels / tires? Those are sick!!!!
@Violator-RCАй бұрын
Thanks. These are the Alf Extreme tires available on our local shopping app here in PH, it's Indonesian made, I'm not sure if it's available in your Country.
@Violator-RCАй бұрын
Here's the updated build. kzread.info/dash/bejne/ioR1q5JmnrPOmMY.htmlsi=rhnQQnRoeHztDZMW
@terriblemem0Ай бұрын
What wheels and tires you use ?
@Violator-RCАй бұрын
s.shopee.ph/AKFBFnpw5E
@terriblemem0Ай бұрын
Thank you! 👍🏼 @@Violator-RC
@Violator-RCАй бұрын
@@terriblemem0 you're welcome.
@shieng3847Ай бұрын
Nice one bro
@Violator-RCАй бұрын
Thanks bro.
@NamVu-mq1jk2 ай бұрын
According to you, which one should I choose c24 and c54?
@Violator-RC2 ай бұрын
I'd go for the c54
@s3th_editz7422 ай бұрын
Where did you get the skid plate from?
@Violator-RC2 ай бұрын
It's available on our local shopping app here in PH but I found it on amazon www.amazon.com/misppro-Stainless-Protector-Crawler-Upgrades/dp/B0C3C2147Z
@isaacrios44242 ай бұрын
How did you attach the stock wheels to the rear window like that?
@Violator-RC2 ай бұрын
I used a zip tie.
@isaacrios4424Ай бұрын
@@Violator-RC what suspension?
@Violator-RCАй бұрын
@@isaacrios4424 on this video it's still using the stock suspension. Here's the update build. kzread.info/dash/bejne/ioR1q5JmnrPOmMY.htmlsi=CN_u3-bozSnXDifL and kzread.info/dash/bejne/ioR1q5JmnrPOmMY.htmlsi=CN_u3-bozSnXDifL
kzread.infor577Nc8ZNtI?si=7JSbSm992VUmvMLR This is my updated run with the alf sportivo tires.
@desertleo42972 ай бұрын
Very impressed with your handy work 👍
@Violator-RC2 ай бұрын
Thank you so much. I appreciate the support.
@raident292 ай бұрын
astig bro!
@Violator-RC2 ай бұрын
Salamat bro.
@TorLeg222 ай бұрын
Supercool!! how thick styrene did you use to make this?
@Violator-RC2 ай бұрын
Thanks. Used 1mm styrene then combined them to 4mm.
@desertleo42972 ай бұрын
What wheels are those?
@Violator-RC2 ай бұрын
I'm using the Alf extreme tires on this video. You can check the updated build here. kzread.info/dash/bejne/ioR1q5JmnrPOmMY.htmlsi=bSWxodnIhTvP3sQj and here kzread.info/dash/bejne/k3yducZpqJzHZrw.htmlsi=GUoMaG2kfoFgz23J
@wltoysxtreme2 ай бұрын
That was deeeeep
@Violator-RC2 ай бұрын
It is deep, I thought it was going to get stuck in the mud.
@DadangsulaemanDadang-jw4ze2 ай бұрын
Wawww keren keren 👍🏻👍🏻👍🏻
@Violator-RC2 ай бұрын
Thank you so much.
@user-yf5jw9tv5k2 ай бұрын
Nice
@Violator-RC2 ай бұрын
Thank you so much.
@SouthernRCGarage2 ай бұрын
Best looking MN82 I have seen. Well done. ❤️❤️👍👍
@Violator-RC2 ай бұрын
Thank you so much.
@pandacrawler6x62 ай бұрын
W😮W Awesome job my Friend 🎉Congrats 🐻❄️🏆🐼👌🏻
@Violator-RC2 ай бұрын
Thank you so much!
@pandacrawler6x62 ай бұрын
You're welcome my Friend 🎉
@raident292 ай бұрын
astig!
@Violator-RC2 ай бұрын
Salamat bro.
@pandacrawler6x62 ай бұрын
Nice Mods 🐼👍🏻
@Violator-RC2 ай бұрын
Thanks. I have an updated version of this MN82 on my channel you can check it out as well.
@pandacrawler6x62 ай бұрын
You're welcome my Friend ❤ I will watch 🎉
@Violator-RC2 ай бұрын
@pandacrawler6x6 Thank you.
@pearlborneo81732 ай бұрын
Can do a waterproofing tutorial for this specifi mn82? Ur video is awesome btw. ❤❤❤❤
@Violator-RC2 ай бұрын
Thank you. I'll try to make one. Usually I just use a nail polish.
@pearlborneo81732 ай бұрын
Cool video bro ❤❤ can do a specific video waterproofinh this specific model mn82? Tqtq
@Violator-RC2 ай бұрын
For the stock electronics you can just use a nail polish, I'll try to make a video of it I'll just have to find a stock elecs since I have given mine away.
@raident292 ай бұрын
san ito banda sa UP paps?
@Violator-RC2 ай бұрын
malapit to sa sunken garden dun sa tindahan na tabi tabi.
@raident292 ай бұрын
@@Violator-RC aahh! paano mo dinadala crawler mo dyan? haha! pag sunday kaya pwede maglaro dyan? dami kasi natakbo parang nakakahiya dalhin hehe!
@Violator-RC2 ай бұрын
@@raident29 bag lang sir tapos padyak lang din ako hehe tuwing weekend ako naglalaro madalas wala nmana hassle maglaro.
@raident292 ай бұрын
@@Violator-RC aahh pwede nga hehe! galing pa ako south kaya mag park nalang ako sa medyo malapit tapos lakad.. sayang nga eh kagagaling ko lang ng UP ngayon at nag jogging. dami nga spot ako nakita na malapit sa sunken.
@Violator-RC2 ай бұрын
@@raident29 madami tagong spot na maganda sa UP pag nalibot mo sir
@ungurdani83463 ай бұрын
Salut my friend super car super video subscribe subscribe .
@Violator-RC3 ай бұрын
Thank you so much!
@ideanet11563 ай бұрын
❤️
@fredericmanuel83473 ай бұрын
J'ai fait exactement pareil Ont a eu la même idée Ont est pas con😅
@Violator-RC3 ай бұрын
Les grands esprits se rencontrent
@raident293 ай бұрын
sang spot ito paps? sa may UP ba ito?
@Violator-RC3 ай бұрын
sa may UP to sir malapit dun sa mga tindahan na tabi tabi.
@SouthernRCGarage3 ай бұрын
Inspiring build. Great job. 👍👍💯💯
@Violator-RC3 ай бұрын
Thanks, I appreciate it.
@raident293 ай бұрын
how did you mount the spare wheel?
@Violator-RC3 ай бұрын
Just a black zip tie
@raident293 ай бұрын
ganda, tagal lang mag ship from shopee. overseas kasi
@Violator-RC3 ай бұрын
konting tyaga lang darating din yan
@Abdulrahman_T7473 ай бұрын
Today I took it off-roading in the beach but it fell in the water half of the car was covered and it starts moving by itself can you tell me why?
@Violator-RC3 ай бұрын
Did you waterproof the electronics?
@Abdulrahman_T7473 ай бұрын
@@Violator-RC no
@Abdulrahman_T7473 ай бұрын
@@Violator-RC is there a way to fix it or not because I’m letting it dry rn
@Violator-RC3 ай бұрын
@@Abdulrahman_T747 You can try to turn it on again once it completely dries. Dry the electronics and the battery completely. But in case the electronics are fried then you have to replace the electronics by buying a esc and a Rx/tx
@Abdulrahman_T7473 ай бұрын
@@Violator-RCshould I buy a new mn82 the beige or lc79 the red because I can’t find where to buy the Esc and the rs/tx
@dwadventures35313 ай бұрын
Where did you get the wheel arches from please
@Violator-RC3 ай бұрын
Here are the links for the files. www.thingiverse.com/thing:5239230 www.thingiverse.com/thing:5718285
Пікірлер
Grabe yung motor, may part na parang nagwawala sa lakas 😅
@@johnpaulpunla3357 nadaan sa 3s bro.
@@johnpaulpunla3357 may full run ako sa fb limited ksi yung dito sa yt shorts.
is the stock mn82 waterproof ready? or do we have to purchase a certain part to make it waterproof?
@@kyusha5122 you have to use nail polish on the electronics ro make it water resistant.
@@Violator-RC ohh ok ok do i need to extend the antenna from the circuit board? or just put a nail polish too on that short antenna?
@@kyusha5122 no need for the antenna.
@@Violator-RC ohh ok... coz i saw a post about the mn82 getting submerged under the water and the rc stopped working although the board is waterproof it says the antenna is too short and its way under the water and stops working but after removing it from the water it works again
@@kyusha5122 If the antenna is submerged underwater then the signal is going to drop. I thought you meant putting nail polish on the antenna :D
cars in offroad outlaws be like when you install a snorkle:
pretty much.
Love the vid what thicknesses the styrene?
Thank you. I used 1mm thickness then put them together to create a 4mm thick walls and support.
💞Wow💞💜💜💜💜💜💜💜💛
Thank you so much!
Oi gente, sou do Brasil 🇧🇷 ! meu sonho é uma dessas eu sou apaixonado, só que aqui tá muito caro, vcs não poderiam me enviar uma de presente?
qual o tamnaho desses amortecedores ? manda o link de onde comprou
www.amazon.com/Vgoohobby-Absorber-Damper-Compatible-Crawler/dp/B0C6JMJW2W/ref=sr_1_1?crid=VSWVT5UTZ7CN&dib=eyJ2IjoiMSJ9.ZCh_bSXbIzHp-3XFtZdwgT-v6QuaewniAkglHAzhTEvGjHj071QN20LucGBJIEps.FeM9JQBcs_39T843KIghE4RyF83CilQ_B1RT6j5XiaA&dib_tag=se&keywords=mn128%2Boil%2Bshocks&qid=1720937945&sprefix=mn128%2Boil%2Bshoc%2Caps%2C548&sr=8-1&th=1
if you're planning on using the stock bed you might have to trim since this is too long for mn82. I just used this to cater to the canopy weight.I also made a custom shock towers for it.
Entendi, muito obrigado.
@@guilhermepassos8930 you're welcome.
I'm currently making something like this to but I'm using PVC pipe that got flatten
That's nice. PVC is very durable. I hope I see your setup soon.
I have a new project right now, I'm replicating the maverick viper 16 camper trailer
@@Violator-RC cool
@@Violator-RC sure i will appload some short video of it when I'm done ❤️❤️
@@MNRc-crawler awesome. Tag me up!
Nice build. ✌😎 what glue do you use? Best from Denmark
@@mickeysrccrawlThanks. I used oily super glue.
@@Violator-RC year, but can read the green label
@@mickeysrccrawl it's a Chinese brand and the only English on it says oily glue.
@@mickeysrccrawl Tree Frog Oily Glue,Welding High-Streth Oily Glue,Repair Glue for Electrical,Electronic,Craft,Rock,Glass,Plastic,Toy-1.8oz a.co/d/0cEyuaaP kinda like this but mines Chinese
@@Violator-RC thanks :-)
I'm a bit in a situation, should I buy MN99s, Mn78, Mn82, or Wpl C24? great video btw!
Thank you. I'd recommend to go for the MN82 but the 99 and 78 are great as well.
@@Violator-RC Thank you!
@@Rs-fg1rz Welcome.
On the receiver module , there is 6 pin plug is empty any idea whats that for ?
@@thecomedyhouse123 I think that's for the light kit but I'm not really sure.
anong tawag po ba nong tube? o may link po kayo sa shoppe?
@@oyemstvofficial s.shopee.ph/3fioWVjAKA Yung NASA video 4mm sukat nyan.
@@Violator-RC thanks po
@@oyemstvofficial welcome.
isa pa po hehehe, yung sheets ilang mm po, nahihirapan ako pag pvc, mas maganda yung gamit nyo at cutter lang pwede na
@@oyemstvofficial 1mm yung kapal Ng styrene sheet na gonagamit ko. Makapal pag PVC Kasi Kaya mas mahirap yun
Nice, hindi mona kailangan umorder sa shopee hehe
@@johnpaulpunla3357 oo nga laking tipid enjoy pa hehehe.
I just one of this just waiting to arrive❤
You're going to love this one.
Loved the work! great video. Very inspiring. #Respect
Thank you so much. I really appreciate it.
how did you cut the styrene?
I used a box cutter.
@@Violator-RC thank you so much
@@s3th_editz742 you're welcome.
отличная модель, купил себе тоже такую!
Nice. This is an awesome trail truck with lots of after market support.
Comprei também, estou aguardando chegar 🇧🇷
@@gustavoaraujo6278 It's worth the wait.
Oi gente, sou do Brasil 🇧🇷 ! meu sonho é uma dessas eu sou apaixonado, só que aqui tá muito caro, vcs não poderiam me enviar uma de presente?
is it waterproof? if it is how did you do it?
It is waterproof, I'm using a cheap 60a esc on this one which is waterproofed already then I waterproofed the dumborc receiver using nail polish then wrapped a breathable fabric on the 370 motor so the water that comes inside the motor will be filtered.
@@Violator-RC thank you
@@s3th_editz742 no worries.
Where do you buy the plastic materials?
Ordered styrene from our local shopping app here in PH.
Hey man what materials did you use?
Styrene.
Can you tell me where to get the wheels / tires? Those are sick!!!!
Thanks. These are the Alf Extreme tires available on our local shopping app here in PH, it's Indonesian made, I'm not sure if it's available in your Country.
Here's the updated build. kzread.info/dash/bejne/ioR1q5JmnrPOmMY.htmlsi=rhnQQnRoeHztDZMW
What wheels and tires you use ?
s.shopee.ph/AKFBFnpw5E
Thank you! 👍🏼 @@Violator-RC
@@terriblemem0 you're welcome.
Nice one bro
Thanks bro.
According to you, which one should I choose c24 and c54?
I'd go for the c54
Where did you get the skid plate from?
It's available on our local shopping app here in PH but I found it on amazon www.amazon.com/misppro-Stainless-Protector-Crawler-Upgrades/dp/B0C3C2147Z
How did you attach the stock wheels to the rear window like that?
I used a zip tie.
@@Violator-RC what suspension?
@@isaacrios4424 on this video it's still using the stock suspension. Here's the update build. kzread.info/dash/bejne/ioR1q5JmnrPOmMY.htmlsi=CN_u3-bozSnXDifL and kzread.info/dash/bejne/ioR1q5JmnrPOmMY.htmlsi=CN_u3-bozSnXDifL
@@isaacrios4424 kzread.info/dash/bejne/k3yducZpqJzHZrw.htmlsi=xPCxTpz0uw9PkgrQ
🫡 nicely done
Thanks.
kzread.infor577Nc8ZNtI?si=7JSbSm992VUmvMLR This is my updated run with the alf sportivo tires.
Very impressed with your handy work 👍
Thank you so much. I appreciate the support.
astig bro!
Salamat bro.
Supercool!! how thick styrene did you use to make this?
Thanks. Used 1mm styrene then combined them to 4mm.
What wheels are those?
I'm using the Alf extreme tires on this video. You can check the updated build here. kzread.info/dash/bejne/ioR1q5JmnrPOmMY.htmlsi=bSWxodnIhTvP3sQj and here kzread.info/dash/bejne/k3yducZpqJzHZrw.htmlsi=GUoMaG2kfoFgz23J
That was deeeeep
It is deep, I thought it was going to get stuck in the mud.
Wawww keren keren 👍🏻👍🏻👍🏻
Thank you so much.
Nice
Thank you so much.
Best looking MN82 I have seen. Well done. ❤️❤️👍👍
Thank you so much.
W😮W Awesome job my Friend 🎉Congrats 🐻❄️🏆🐼👌🏻
Thank you so much!
You're welcome my Friend 🎉
astig!
Salamat bro.
Nice Mods 🐼👍🏻
Thanks. I have an updated version of this MN82 on my channel you can check it out as well.
You're welcome my Friend ❤ I will watch 🎉
@pandacrawler6x6 Thank you.
Can do a waterproofing tutorial for this specifi mn82? Ur video is awesome btw. ❤❤❤❤
Thank you. I'll try to make one. Usually I just use a nail polish.
Cool video bro ❤❤ can do a specific video waterproofinh this specific model mn82? Tqtq
For the stock electronics you can just use a nail polish, I'll try to make a video of it I'll just have to find a stock elecs since I have given mine away.
san ito banda sa UP paps?
malapit to sa sunken garden dun sa tindahan na tabi tabi.
@@Violator-RC aahh! paano mo dinadala crawler mo dyan? haha! pag sunday kaya pwede maglaro dyan? dami kasi natakbo parang nakakahiya dalhin hehe!
@@raident29 bag lang sir tapos padyak lang din ako hehe tuwing weekend ako naglalaro madalas wala nmana hassle maglaro.
@@Violator-RC aahh pwede nga hehe! galing pa ako south kaya mag park nalang ako sa medyo malapit tapos lakad.. sayang nga eh kagagaling ko lang ng UP ngayon at nag jogging. dami nga spot ako nakita na malapit sa sunken.
@@raident29 madami tagong spot na maganda sa UP pag nalibot mo sir
Salut my friend super car super video subscribe subscribe .
Thank you so much!
❤️
J'ai fait exactement pareil Ont a eu la même idée Ont est pas con😅
Les grands esprits se rencontrent
sang spot ito paps? sa may UP ba ito?
sa may UP to sir malapit dun sa mga tindahan na tabi tabi.
Inspiring build. Great job. 👍👍💯💯
Thanks, I appreciate it.
how did you mount the spare wheel?
Just a black zip tie
ganda, tagal lang mag ship from shopee. overseas kasi
konting tyaga lang darating din yan
Today I took it off-roading in the beach but it fell in the water half of the car was covered and it starts moving by itself can you tell me why?
Did you waterproof the electronics?
@@Violator-RC no
@@Violator-RC is there a way to fix it or not because I’m letting it dry rn
@@Abdulrahman_T747 You can try to turn it on again once it completely dries. Dry the electronics and the battery completely. But in case the electronics are fried then you have to replace the electronics by buying a esc and a Rx/tx
@@Violator-RCshould I buy a new mn82 the beige or lc79 the red because I can’t find where to buy the Esc and the rs/tx
Where did you get the wheel arches from please
Here are the links for the files. www.thingiverse.com/thing:5239230 www.thingiverse.com/thing:5718285