Пікірлер

• 
  @johnhylant998811 күн бұрын

  Good luck with a mechanical fuel tank and a double pump will operate wipers better. I've tried 3 pumps and now there's an electric 6v pump. 6v wasn't too hard to find

• 
  @stevepope548416 күн бұрын

  I installed a stationary antenna on the 99 /from a explore without power antenna. Because I can't find a power replacement! Now I need an antenna coupler. Now I've got two male antenna ends. I'll see after I get the coupling if it works. It's been a long while since I took out the power antenna. Seems like it had wires that might have went to the amp.in the rear? Too bad I can't get the power antenna.

• 
  @jamesspano2335Ай бұрын

  Is your truck a SuperCrew with four doors?

• 
  @jamesspano2335Ай бұрын

  Is it possible to cut a hole in the bed please reply

• 
  @EnerdhilАй бұрын

  Thank you for this video. My car happened to be. 2002 Corolla and so I found everything exactly where you showed us it was. The electrical connection was stuck and took a while of trying before I could disconnect it. The new sensor was slightly different from the original, but fit perfectly into place. Thanks again. I couldn't have done this without your help. God bless you.😁👍

• 
  @WV5913 ай бұрын

  what's the correct belt tension on these 2005 sentra?

• 
  @sonnyc38263 ай бұрын

  thanks for the video...im goign to start changing my own oil to save seom money

• 
  @MrTomtodd3 ай бұрын

  The absolute best connector is heat shrink with soder built into the connector.

• 
  @jeffblank97673 ай бұрын

  Thanks for the safety trick about the battery

• 
  @spicypeppers20194 ай бұрын

  amber bulb behind a red lens. interesting…

• 
  @user-rs6xb8so9d4 ай бұрын

  What about the fourth cylinder

• 
  @aPoorsPerspective6 ай бұрын

  Make sure you have the engine just a little warm so the oil will remove more sludge and contaminants.

• 
  @abelmanteca59026 ай бұрын

  You need to throw those away very far

• 
  @jorgemora71906 ай бұрын

  Wow very good job body we learn everyday thanks

• 
  @larrysalzman71656 ай бұрын

  My problem while replacing the MAP SENSOR is getting the rubber 'L' to go onto the tube from the throttle body. Three times put the sensor into place, but that rubber piece is being uncooperating. Any good suggestions? Thanks for a reply.

• 
  @larrysalzman71656 ай бұрын

  After four failed trys to get the rubber L onto the throttle plate tube with moving to the side away from the nozzle port.....I rechecked my thinking. I slide the rubber tube onto the nozzle first, keeping it centered. Attach screws loosely and with a small screwdriver and bend the top on rubber L back towards you and put in the two screws of the Map Sensor tight. Once the sensor is in place ,, push UP the rubber tube onto the Map Sensor inlet tube, so now it's in place. Started engine,,,ran smooth. This system worked for me, so if you are having the same problem that I had, this should help you. Good luck.

• 
  @Joe-rd8we7 ай бұрын

  Water pump replacement not engine overhaul?

• 
  @alpinehs7 ай бұрын

  Great video

• 
  @shua93478 ай бұрын

  THANK YOU

• 
  @lenchonegro55679 ай бұрын

  This is pretty thorough. 😊

• 
  @samuelherman48599 ай бұрын

  Excellent video but you should explain what was the problem with the truck before you install everything you know bro

• 
  @gg6ft79 ай бұрын

  This was great. Thank you. Saved me about $100.00

• 
  @erichkorman7109 ай бұрын

  Unfortunetly the mechanic has zero experience with engine development, certainly not with testing cold air intakes on a Dynometer. The team I worked with abroad had three, the smallest able to read as low as 1/4 HP. Intake temp does not change much without an intercooler but they reduce or eliminate design restrictions, noise baffles etc. Of dozens most produce 5-10 HP if done correctly; we had over 15 HP+ on some engines that had high-flow exhausts etc with stock air boxes and filters. Many of our mechanics today think they know everything about not just mechanical things without any basis but "seat of pants" research as well as more about Virology, Climatology, or if a mask can stop transfer. Until they need an operation! With smarts dropping from attacks on schools we have to import hundreds of thousands of engineers and scientists each year because some now think any profession like engine development that takes more knowledge than home skoolin' at the kitchen table & maybe a GED or even an actual education is just lies to confuse slower brains! Many things like special plugs etc will not budge a Dyno readout. Exhausts & intakes on newer vehicles are better than an amateur can do but sound or the change in feel can fool you. If the exhaust is too restrictive or the engine intake is tuned for low-end an intake will just change feel at certain RPM. You need a dynometer to know but engines are air pumps so of course flow & volume matter. If all you see is old tools and grungy garages get performance improvement advice from experts with the neccesary learning when trying to improve anything. As for changing a TPS over testing if the original sensor, idle air control or mass air flow sensor are over 15 years or near 100k miles old they are so cheap replace them anyway, they are so cheap online and can really sharpen up what seems to be working fine already.

• 
  @stevewheatley24310 ай бұрын

  Those Ford quick disconnects aint so quick sometimes. Not after they been there for yrs.

• 
  @jamesbarnes704511 ай бұрын

  Bro take that nasty ass ashtray out of the video nobody wants to see or smell that stinking ass shit

• 
  @markcreel9258 Жыл бұрын

  Thanks, awesome job

• 
  @user-ix9yu8ue8q Жыл бұрын

  You do not loosen the two 14 mm bolts..you loosen the idler pulley bolt which is on a slide. Just like the outer belt it secures the adjuster in place once adjusted.

• 
  @MyLooneyBin Жыл бұрын

  Great video man. I'm going to be giving it a shot. Appreciate the tips on my 2004 Honda Accord

• 
  @classicstangbrn8964 Жыл бұрын

  Just did the same repair tonite, same door even the truck is the same color but mine is a 2003 and the door panel hooks in place, no chrismas tree fasteners, thank god.

• 
  @Tom-ic7hw Жыл бұрын

  I think I'll just use my angle grinder with a cutoff wheel and make an access hole in the bed my truck isn't that nice plus I got slide in bed liner to hide the hole

• 
  @betochipistube6543 Жыл бұрын

  Thank you Sir

• 
  @JuInTheTrap404 Жыл бұрын

  Thanks you, just saved a broke college student a few bucks 🙏🏽

• 
  @tyarb52 Жыл бұрын

  Good teaching but cant see anythingabout the clips etc

• 
  @texxs01 Жыл бұрын

  10 years and they're price is a little more than double . . .

• 
  @Clearanceman2 Жыл бұрын

  I bought a milwaukee 1/2 inch 1400 ft. pound impact because of my first experience doing the crank bolt on this. Some guy on you tube broke six honda crank bolts in a row with the same battery at a junk yard and it just spins it off like it's nothing.

• 
  @Clearanceman2 Жыл бұрын

  Seems like the hardest part of the whole thing is getting the lower timing cover back on. I've resorted to pulling three motor mounts and moving the engine over. Also, one of my water pump bolts stripped and the fun of doing a helicoil in there. I did it though right angle adapter with right angle drill with 1 inch 1/4 inch drive stuby bit. The helicoil brand takes a 1/4 inch drill bit which comes in a set of 1/4 inch drive stubby bits from amazon. It was not fun. 6m x 1 bolts like to strip.

• 
  @darcyfoster5982 Жыл бұрын

  Just pull the 6 50 torx bolts off thr bed and move the box back 3 ft. The whole operation to mo e the box off is about ten minutes and you can do everything from above.

• 
  @giovannipg3000 Жыл бұрын

  Does it destroy the rubber seals ?

• 
  @amazingdamy5012 Жыл бұрын

  This is still helpful till today.

• 
  @TYGON100 Жыл бұрын

  Thanks!!!....i have to change the drive belts in my sentra special 2006

• 
  @estebangarcia1673 Жыл бұрын

  Hey boss, love the video is there any chance you could provide tips or a video on replacing a thermostat housing? Cracked it yesterday and it looks like it goes under my engine head and im not sure what to do

• 
  @waveland0 Жыл бұрын

  Slider bolt is 14 mil and not 9/16. 9/16 is slightly bigger and I ended up rounding off the stuck bolt with it. Wasted time and money getting an extractor socket set.

• 
  @normanalvarez5751 Жыл бұрын

  Recommendation fill the oil filter with oil 1st

• 
  @iamozzman990 Жыл бұрын

  "Crank it up to 11" why not make 10 one higher? Spinal Tap... Good video.

• 
  @wayneflemmer2607 Жыл бұрын

  Well after watching this I'm cutting an access door in the bed of the truck way easier than all this. Takes about 20 minutes and you are right there. Unbolt it take it out no breaking things put the new one in and that's it.

• 
  @jamesspano2335Ай бұрын

  Were you able to get to the fuel pump by cutting the bed if so can you send me a picture.

• 
  @koraku8519 Жыл бұрын

  Amazing. You single handedly helped me get my belt back on thank you

• 
  @stevendorey280 Жыл бұрын

  Do you think it would free up a stuck plunger for the choke?

• 
  @walterleblanc4485 Жыл бұрын

  The only reason I watched was to figure out what size wrench, the fucker goes over everything else but...

• 
  @JoseDominguez-gf7xk Жыл бұрын

  Great video It helps a lot just in the part when you put the new pump you forget to install the new seal at least that you installed before you finish the video

• 
  @richardcondit3462 Жыл бұрын

  Please get a windscreen for your mic. So distracting.

• 
  @garymackey850 Жыл бұрын

  Absolutely loved the cardboard box idea....thanks!