Thanks a lot man! I fixed the same issue in the CP800 thanks to this, same issue, same split plastic arm, used superglue and some string to keep tension while the glue dries, will probably add a zip tie if the tolerances are right
@karllaun24273 ай бұрын
Thanks so much for making this video. I recently pulled out my Selphy CP-760 which until now had been working just fine. After resolving a maddening issue with images not showing in the preview screen, then I found I was getting only half a print as seen in your video. I ended up having to fully disassemble my machine to actually see the split. If someone else goes down this path there's a lever arm on the PCB side of the printer that can rotate to release the metal rod. I ended up using JB Weld and some fine stainless steel safety wire to secure the nylon fitting to the rod. After reassembly, I was VERY disappointed to find it didn't work (blank prints). Took it apart again and made sure the fitting under the PCB was pushed down enough to engage with the drive gear. Success!. Disassembly/assembly the first time took a couple hours. Second time about 15 minutes (many tight ribbon cable connections).
@filipkovac28687 ай бұрын
Thanks for this video. Helped me to repair the printer. As I see you prevented a lot kilos of garbage in the world. Good work!
@SSUKBD10 ай бұрын
Hi, Need some Help here. I printed some photo with this Canon Selphy cp510 printer using my laptop. The problem I am facing is, no matter what size I select it's printing SMALL size picture. I selected 4 x 6 inch from the laptop. The Photo paper was 7 x 4 inch But it's printed in the middle like 3 x 2 inch size. Why? I uploaded a video of it in my KZread channel as a Short, please have a look. I am unable to post a link as it will delete this message.
@karinevandecatsije967711 ай бұрын
Thanks a lot for the tutorial. I bought it at a flea market without knowing if it was still working. Thanks to you I repaired it myself. Greetings from Belgium. Karine
@jimmychang191311 ай бұрын
Thank you for video. I have CP1200 and it was same issue without the split. Gave a little pressure and it printed perfectly. Now to add a tiny drop of oil, hopefully it won’t happen again.
@SammYLightfooD Жыл бұрын
I wanted to print a Birthday Card today but my Selphy printer showed exactly this failure. I opened it up and yes the right lever had a very fine crack. Unfortunately it was located on the bottom side, so I continued to remove the pcb on the left side and find out that the gear rotates a shaft inside the metal tube. I was able to unhook the tube, remove the lever, superglue it, put it back on, mount the tube, strap a zip-tie and put everything together again. Electronically it worked but mechanically it did not. Something went wrong along the way, but I bet that's just bad handling/luck in my case. I'm not sad bc. its an old Selphy CP 720 which lasted for 15 years and it also had a problem with paper feed, so I guess that piece has reached its end of life. Thanks for the video, interesting and I'm sure many can be fixed.
@TaC084 Жыл бұрын
Thnx! Works!
@weslyng77 Жыл бұрын
Thank you, but for my situation, the plastic part didn't break, but if I forced it down when printing, it works at the first time. After the first one, the second one even press it very hard, it's not work.
@xenover Жыл бұрын
Worked for my CP-510! Thanks a lot!
@propeller4711 Жыл бұрын
👍👍👍Thanks to your instructions, I was able to repair my CP710!!! Thank you very much
@future-matze-35 Жыл бұрын
Thank you so much!! The fix totally worked with my old Selphy CP760. Thanks for sharing, you're awesome!
@kevintan18862 жыл бұрын
Thank you for saving me from having to buy a new printer and saving the printer from going into garbage heap :)
@9ernie92 жыл бұрын
Fixing my CP400 with the help of this video. I hadn't noticed the crack in this plastic part. Super video. Many thanks for uploading it. Save me buying a new printer!
@awsali20112 жыл бұрын
Thnx a lot
@rado5952 жыл бұрын
Thank you so much!
@antoniocanclini65532 жыл бұрын
Thank you for the video, I'd like to try but I would like to be sure I use the correct glue. Which one do you suggest? Also: the crack in the plastic is in the bottom part, not visible from the top. How do you suggest to glue it? Thanks!
@peterkann62702 жыл бұрын
thanks for this super video. i have the same problem. next day´s i will fix my printer. happy new year and greetings from Kassel germany.
@mayolgll88552 жыл бұрын
Thank you for this!
@sarahalrayyan25202 жыл бұрын
I recently bought this printer at the thrift store for $6 and it had this problem I just fixed it yesterday and I finally was able to print a perfect picture Thanks for your onsite on how to fix the printer
@chrisjuh68262 жыл бұрын
YES, dit the job for me too! Great tutorial, dit the job for my 510 too
@raypilon532 жыл бұрын
100% fixed the problem. How come Canon doesn't address this when they update their equipment? Why use shitty material?
Tired of Canon using shit parts in their photo printers. Both of my printers suffer from this same problem (one is much newer than the other).
@melen_s3 жыл бұрын
Thank you, you saved my printer!
@ishayleviishay3 жыл бұрын
thanks you! you saved my printer! #RightToRepair
@Kareldar3 жыл бұрын
Buenas tardes, uff yo tengo una Sony y gracias a ti pude detectar la falla, es exactamente la falla que tengo. mil gracias. exelente video
@pskovich60823 жыл бұрын
Спасибо!
@janvanderstraeten75313 жыл бұрын
thanks man, cp 400 with the same problem, had it for years and love it
@wenjin883 жыл бұрын
Thank you!! The solution also works on cp800
@Andyatallah3 жыл бұрын
Thanks from Syria/
@al3x4et03 жыл бұрын
Thank you very much for the help! :)
@Bos-Q3 жыл бұрын
2020. thanks for my selphy printer problem solution. made in china all the same problem.
@vladyslavyurievichfilonenk30513 жыл бұрын
Спасибо, Бро!
@hipotos3 жыл бұрын
Fantastic!!!! Mercy!
@erkintelorman83243 жыл бұрын
Thank you so much :)
@taydoow4 жыл бұрын
Don’t know where you found the super skinny cable tie but even my tiniest is snagging the movement. I will try using some wire instead I think. Thanks for the excellent video tutorial 👍🏼
@simonbarreto33144 жыл бұрын
Wonderful! It worked with my Canon CP760. I fixed it today. Thank you. Brazil
@dianevitale12144 жыл бұрын
You do excellent repair on this. Have a CP900 Selphy which a fine vertical line appears on each print out. As read, might be dust. Do you know a way to clean best? Know this video is old, but thought I'd give it a try to ask.
@reecekettle4114 жыл бұрын
Thanks! My Selphy had same problem but cracked on bottom where not visible. Not enough clearance for the zip tie, I had to Dremel a little metal away to make room but now it's back to 99% (still a 1/4" along elge where it's faint).
@Stellar123164 жыл бұрын
Excellent! mine is printing the same way. I love your accent ! great job very helpful, cheers!!
@filippofranzo50364 жыл бұрын
Hello.. I have a problem my cp510 dice dice dice Dell ink danelli unseted. I put one but I have it problem
@franciscojaviersanzvicente30464 жыл бұрын
Thanks so much for your professional and clear video !!!!. I have solved this same issue with my CP200, Kind regards....
@kamhengho89824 жыл бұрын
Thanks for the video. We fixed our CP730! Canon Selphy is a great device, still running after all these years, but to let that piece of plastic to ruin the whole product is a disappointment.
@bat21sm4 жыл бұрын
tnk you i fix my print
@rlanub004 жыл бұрын
Hello, I have a similar problem for my nice CANON Selphy CP720. Do you know anybody who I can send the printer and get it repaired? If I open the printer and push the press on the paper, pictures are printed perfectly. I tried clamping on the shaft with a plastic strap but I was not able to fix it. unfortunately CANON support does not provide any part and any service for this model. Any help?
@picasso30415 жыл бұрын
you are king
@MassimoDAgostino785 жыл бұрын
Thanks, I had the same problem on my selphy 530.
@love4lust73015 жыл бұрын
cute dog
@benjaminroos23425 жыл бұрын
I have a cp910 and it is also printing half but the white part seems fine after checking it...
Пікірлер
Thanks a lot man! I fixed the same issue in the CP800 thanks to this, same issue, same split plastic arm, used superglue and some string to keep tension while the glue dries, will probably add a zip tie if the tolerances are right
Thanks so much for making this video. I recently pulled out my Selphy CP-760 which until now had been working just fine. After resolving a maddening issue with images not showing in the preview screen, then I found I was getting only half a print as seen in your video. I ended up having to fully disassemble my machine to actually see the split. If someone else goes down this path there's a lever arm on the PCB side of the printer that can rotate to release the metal rod. I ended up using JB Weld and some fine stainless steel safety wire to secure the nylon fitting to the rod. After reassembly, I was VERY disappointed to find it didn't work (blank prints). Took it apart again and made sure the fitting under the PCB was pushed down enough to engage with the drive gear. Success!. Disassembly/assembly the first time took a couple hours. Second time about 15 minutes (many tight ribbon cable connections).
Thanks for this video. Helped me to repair the printer. As I see you prevented a lot kilos of garbage in the world. Good work!
Hi, Need some Help here. I printed some photo with this Canon Selphy cp510 printer using my laptop. The problem I am facing is, no matter what size I select it's printing SMALL size picture. I selected 4 x 6 inch from the laptop. The Photo paper was 7 x 4 inch But it's printed in the middle like 3 x 2 inch size. Why? I uploaded a video of it in my KZread channel as a Short, please have a look. I am unable to post a link as it will delete this message.
Thanks a lot for the tutorial. I bought it at a flea market without knowing if it was still working. Thanks to you I repaired it myself. Greetings from Belgium. Karine
Thank you for video. I have CP1200 and it was same issue without the split. Gave a little pressure and it printed perfectly. Now to add a tiny drop of oil, hopefully it won’t happen again.
I wanted to print a Birthday Card today but my Selphy printer showed exactly this failure. I opened it up and yes the right lever had a very fine crack. Unfortunately it was located on the bottom side, so I continued to remove the pcb on the left side and find out that the gear rotates a shaft inside the metal tube. I was able to unhook the tube, remove the lever, superglue it, put it back on, mount the tube, strap a zip-tie and put everything together again. Electronically it worked but mechanically it did not. Something went wrong along the way, but I bet that's just bad handling/luck in my case. I'm not sad bc. its an old Selphy CP 720 which lasted for 15 years and it also had a problem with paper feed, so I guess that piece has reached its end of life. Thanks for the video, interesting and I'm sure many can be fixed.
Thnx! Works!
Thank you, but for my situation, the plastic part didn't break, but if I forced it down when printing, it works at the first time. After the first one, the second one even press it very hard, it's not work.
Worked for my CP-510! Thanks a lot!
👍👍👍Thanks to your instructions, I was able to repair my CP710!!! Thank you very much
Thank you so much!! The fix totally worked with my old Selphy CP760. Thanks for sharing, you're awesome!
Thank you for saving me from having to buy a new printer and saving the printer from going into garbage heap :)
Fixing my CP400 with the help of this video. I hadn't noticed the crack in this plastic part. Super video. Many thanks for uploading it. Save me buying a new printer!
Thnx a lot
Thank you so much!
Thank you for the video, I'd like to try but I would like to be sure I use the correct glue. Which one do you suggest? Also: the crack in the plastic is in the bottom part, not visible from the top. How do you suggest to glue it? Thanks!
thanks for this super video. i have the same problem. next day´s i will fix my printer. happy new year and greetings from Kassel germany.
Thank you for this!
I recently bought this printer at the thrift store for $6 and it had this problem I just fixed it yesterday and I finally was able to print a perfect picture Thanks for your onsite on how to fix the printer
YES, dit the job for me too! Great tutorial, dit the job for my 510 too
100% fixed the problem. How come Canon doesn't address this when they update their equipment? Why use shitty material?
Маладэц!Красава блэт! Хомутом починил!Пайду такжи зделаю
Tired of Canon using shit parts in their photo printers. Both of my printers suffer from this same problem (one is much newer than the other).
Thank you, you saved my printer!
thanks you! you saved my printer! #RightToRepair
Buenas tardes, uff yo tengo una Sony y gracias a ti pude detectar la falla, es exactamente la falla que tengo. mil gracias. exelente video
Спасибо!
thanks man, cp 400 with the same problem, had it for years and love it
Thank you!! The solution also works on cp800
Thanks from Syria/
Thank you very much for the help! :)
2020. thanks for my selphy printer problem solution. made in china all the same problem.
Спасибо, Бро!
Fantastic!!!! Mercy!
Thank you so much :)
Don’t know where you found the super skinny cable tie but even my tiniest is snagging the movement. I will try using some wire instead I think. Thanks for the excellent video tutorial 👍🏼
Wonderful! It worked with my Canon CP760. I fixed it today. Thank you. Brazil
You do excellent repair on this. Have a CP900 Selphy which a fine vertical line appears on each print out. As read, might be dust. Do you know a way to clean best? Know this video is old, but thought I'd give it a try to ask.
Thanks! My Selphy had same problem but cracked on bottom where not visible. Not enough clearance for the zip tie, I had to Dremel a little metal away to make room but now it's back to 99% (still a 1/4" along elge where it's faint).
Excellent! mine is printing the same way. I love your accent ! great job very helpful, cheers!!
Hello.. I have a problem my cp510 dice dice dice Dell ink danelli unseted. I put one but I have it problem
Thanks so much for your professional and clear video !!!!. I have solved this same issue with my CP200, Kind regards....
Thanks for the video. We fixed our CP730! Canon Selphy is a great device, still running after all these years, but to let that piece of plastic to ruin the whole product is a disappointment.
tnk you i fix my print
Hello, I have a similar problem for my nice CANON Selphy CP720. Do you know anybody who I can send the printer and get it repaired? If I open the printer and push the press on the paper, pictures are printed perfectly. I tried clamping on the shaft with a plastic strap but I was not able to fix it. unfortunately CANON support does not provide any part and any service for this model. Any help?
you are king
Thanks, I had the same problem on my selphy 530.
cute dog
I have a cp910 and it is also printing half but the white part seems fine after checking it...
How were you able to later resolve it?