Пікірлер

• 
  @reklamyi7Күн бұрын

  Thanks for video, great job!

• 
  @Spellbinding_sagas4 күн бұрын

  Finally found someone working and helping micra K13 owner fix their issues by themselves.

• 
  @matthayes85244 күн бұрын

  Is the bolt on the tensioner reverse threaded by any chance?

• 
  @micradocs4 күн бұрын

  @@matthayes8524 the main bolt that holds the tensioner on is turned anti-clockwise to loosen it, there is another bolt on side also. I have another video on my channel where I replaced the tensioner altogether and I gave a brief explainer. Have a watch it may help

• 
  @matthayes85243 күн бұрын

  @micradocs thanks, I just need to give it some Wd40 and a bigger tool to get it off then

• 
  @rolandcantu875222 күн бұрын

  Yes wear can I take my car to put the abs.thankyou

• 
  @halloweenlisteningparty23 күн бұрын

  Thanks so much for sharing! My sidemirror got swiped, and I was able to replace it!

• 
  @trulycheeseball25 күн бұрын

  Thankyou this is very helpful will be doing this tomorrow

• 
  @xxl_81Ай бұрын

  Hi, what condenser do you build in to replace the old ? There are so many with different massures. My micra is from 2016, k13k 1.2l 80HP

• 
  @micradocsАй бұрын

  Sorry for the delay in replying, I didn't see this message for some reason. There are different ones, but to make sure yours is the right fit make sure you insert your car details correctly when ordering and it will give you a list of suitable options. As long as they fit your car details the branding is up to you really

• 
  @neiliewheeliebinАй бұрын

  Hows the inlet manifold seal after removal? is it reusable?

• 
  @micradocsАй бұрын

  The air intake manifold is fine after removal and can be refitted easily as shown in the video

• 
  @neiliewheeliebinАй бұрын

  @micradocs Thank you for your video & reply I'll be doing my sons car this weekend & wanted to make sure there were no hidden surprises. it looks pretty straight forward thankfully just remove the airbox, 4 throttle body bolts & the intake can come off

• 
  @micradocsАй бұрын

  @@neiliewheeliebin there shouldn't be, follow the video and it should be as it is shown 👍🏻

• 
  @BilgiTv672 ай бұрын

  There are only 3 spark plugs, right K13?

• 
  @micradocs2 ай бұрын

  Yes, that's correct. Only 3 spark plugs.

• 
  @ArgenisAngela19 күн бұрын

  Which the #number on the sparplug you've removed or they're all the same #number???

• 
  @LaurentiuSandu-fq6tb2 ай бұрын

  Hi ! Did you find out eventually where was the issue?

• 
  @micradocs2 ай бұрын

  Yes, it was the crankshaft seal

• 
  @computingaxe15853 ай бұрын

  Hey, your videos on the K13 Micra are great, coming from someone who drives one and maintains it. I wouldn't recommend connecting a device that draws more current than is permitted, simply because there is a chance that the fuse will blow when it may use more current than is permitted. However, you won't really do much harm so it's okay for a temporary solution

• 
  @malleckkadell74133 ай бұрын

  Might have shown the state of the discarded plug..... to get an idea of the combustion. Without any ill will.

• 
  @johnbyrne72293 ай бұрын

  Hi . Do u have video of driver headlight removal ?

• 
  @micradocs3 ай бұрын

  Hi, I don't, but I can make one in a few weeks time

• 
  @johnbyrne72293 ай бұрын

  @@micradocs that would be great . As far as I know front bumper has to be removed

• 
  @secret9463 ай бұрын

  What spark plug spanner is needed to remove the spark plug?

• 
  @enemycrab92293 ай бұрын

  Wondering this, too. Looks like a really long reach.

• 
  @simonbone2 ай бұрын

  14 mm.

• 
  @enemycrab92293 ай бұрын

  Brilliant, thank you! Got to tackle this soon and all the videos I had seen on KZread to date covering the process had either been poorly described, poorly filmed, or both! This is neither. Great video

• 
  @kinggeneral27603 ай бұрын

  By any chance you dont know the part number of this bumper ?

• 
  @micradocs3 ай бұрын

  If you put your car details on the site you want to buy your bumper from then it should list the appropriate one

• 
  @ReggaeNight3 ай бұрын

  Thanks a lot for this video it’s very helpful!

• 
  @amjedmahmood83243 ай бұрын

  Hi dose this fits nissan micra k13 2015 model

• 
  @micradocs3 ай бұрын

  Hi, yes it does. But always good to check the product with your vehicle when purchasing

• 
  @simonbone5 ай бұрын

  Yaay! Done it! It was pretty straightforward, just like in the video. Oddly, the passenger side lower bolt was a lot tougher than the other one to put back into place. Possibly a little bit of rust lock. Otherwise, no surprises. Thanks!

• 
  @danc16605 ай бұрын

  How did you gauge the correct tension for the belt?

• 
  @micradocs5 ай бұрын

  Ideally you should use a torque wrench, but I usually go by feel of the belt, should be nice and tight

• 
  @Karim_Belgique5 ай бұрын

  Question, is it easy to replace the cat on this car and second if i order a cat do they deliver everything to install all? bolts, gasket etc.

• 
  @swallowdiveshefki6 ай бұрын

  An excellent , concise video. Is this for a Micra K13?

• 
  @micradocs6 ай бұрын

  Thanks, should be suitable for all Micra's

• 
  @mondragon1313x6 ай бұрын

  ¿En el Micra K13 sería igual?

• 
  @micradocs6 ай бұрын

  Si, es igual

• 
  @simonbone6 ай бұрын

  How did I miss that you'd done a video on this? Would have saved me hours of trouble! (On the plus side, it helped confirm that I'd done the right thing in the end.)

• 
  @readychalk51456 ай бұрын

  Great content! I need to replace a water pump but watching this has helped me understand how to even get to the bloody thing haha

• 
  @SHEEDATULEE6 ай бұрын

  Thank you for this easy to follow instructional video.. How much ionised water should be filled in…

• 
  @micradocs6 ай бұрын

  The one I got was already mixed. But if you're using ionised water it should be 50% mix

• 
  @shsa30746 ай бұрын

  How do you order the right exhaust? So many places have different kinds even if you put you Reg number in. So confused please help 😊

• 
  @micradocs6 ай бұрын

  If you put your reg in you will get a list of different brands supplying the exhaust, but they should all fit your vehicle. You can also double check it does fit your vehicle when you pick up the part

• 
  @shsa30746 ай бұрын

  Perfect thank you for responding. So my exhaust is exactly like yours it's round. But the replacement one looks more square yet says it should fit...it that normal? Thanks

• 
  @micradocs6 ай бұрын

  @@shsa3074 as long as it says it fits then it should be fine. Some designs vary a little bit it's more the pipe connection that's important.

• 
  @shsa30746 ай бұрын

  Amazing thank you so much.

• 
  @sacplissken7 ай бұрын

  Thanks champ!

• 
  @Bareego7 ай бұрын

  Thanks, wasn't able to reconnect the cable but at least I pushed the white plastic bit so the aircon is cold always now, which is great in Australia

• 
  @IbzJaay198 ай бұрын

  Do you top up to the max mark or just under also Can you use any green colour coolant just to top up if necessary?

• 
  @micradocs8 ай бұрын

  Top it up to the max in the radiator, as for the container as long as it's above the minimum then you should be fine

• 
  @micradocs8 ай бұрын

  Also check your car details for which coolant is suitable for your car

• 
  @arpizoosingh74308 ай бұрын

  How many litres does it take coolant full ??

• 
  @micradocs8 ай бұрын

  I can't remember off the top of my head right now, but as long as the radiator is filled to the top and the container has a good amount then you should be fine

• 
  @drujbanu8 ай бұрын

  Mine blowing cold but unfortunately it’s not the white clip the problem

• 
  @elianelegeek8 ай бұрын

  Merci beaucoup pour ce tutoriel efficace qui m'a sauvé la mise ! Continuez !

• 
  @elvinismailov59488 ай бұрын

  Hello my friend how much you need to tighten the bolt tensioner?

• 
  @erkkihamalainen57258 ай бұрын

  New belt, did few days noise after start, then settles and now quiet as normal. 2006 1.2 ac, replaced in 218 tkm, old belt looked not so worn only a bit. New belt is Gates, old maybe original.

• 
  @simonbone9 ай бұрын

  This is likely the next thing I'll have to do with my Micra pushing towards 100,000 km. Since the one plug is so inaccessible, does it make sense to replace the coil assembly (or anything else) while the manifold is off?

• 
  @bajanspx5 ай бұрын

  Yes. My daughter’s k13 started having coil packs fail around 115,000km. I would replace the plugs and all coils with the 100,000km service as it’s such a pain to get at the cylinder 1 plug and coil. Use the recommended long life spark plugs.

• 
  @simonbone5 ай бұрын

  @@bajanspx Great, I'll do that. Decent coils (NGK, Beru, etc.) are quite expensive so I may just replace the one under the manifold. Unlike the Micra in the video, mine is not supercharged, so two of the spark plugs are easy to do - it's just the one on the front left that's a pain. Might even make sense to change the two easily accessible plugs, and put the new coil on one of them, drive around with them for a week to make sure there are no issues, before replacing the third (and putting the old coil back on the earlier plug).

• 
  @rzyrafa119 ай бұрын

  wrong bolts were used.

• 
  @momfiethehunter5045 ай бұрын

  Double gasket too, didn't remove the old one on camera

• 
  @simonbone9 ай бұрын

  My Micra has an electrical cable clipped to the coolant reserve tank (bracket on the back visible at 2:02), making it exceedingly difficult to remove. I used a pump to suck the fluid out instead and fllushed it once or twice. Also, that radiator drain plug is incredibly flimsy, being made of soft nylon but screwed in very tightly. Very easy to strip the head on it, especially with repeated opening and closing. I added G12+ coolant, which is bright pink. The inevitable trace of the blue/green Nissan coolant left in the system turns it to a dirty orange colour.

• 
  @micradocs9 ай бұрын

  That's a good way to suck the fluid out and give it a clean 👍

• 
  @simonbone9 ай бұрын

  I replaced my Micra's belt by reaching down with the hood open. It was a bit fiddly, but there was no need to remove the wheel or the panels to get to it. There is just enough clearance to do so.

• 
  @micradocs9 ай бұрын

  Yes, there are a few different ways to get to it. This method I uploaded I thought was ideal for those needing more room to manoeuvre :)

• 
  @simonbone6 ай бұрын

  @@micradocs It's a few months later and I now have had to replace the water pump, and while I was at it I changed the tensioner pulley too. I'm now regretting trying to do all this from the top. The tensioner in particular is a real pain because you can't see what you are doing, and it is possible to install it wrong. (Edit:) Ultimately, what I did was to remove the tensioner screw mechanism, unscrew it to the loosest position, then put it back in the correct position and reinstall the pulley on the other side. That way there was plenty of slack for the belt to go on, while I could be sure that the tensioner screw thingie hadn't slipped out of its correct position. But yeah, in all the time it took it probably would have been somewhat easier to go at it from the side!

• 
  @hassan.ali10117 күн бұрын

  Hello friend. Would you mind elaborating on how you did this? I am looking to do it the same way you did. Did you remove any parts out the way to get there? Is there any tutorial u followed or anything ?

• 
  @simonbone17 күн бұрын

  @@hassan.ali101 Assuming you have the same engine (1.2 3-cylinder), it wasn't hard. Once you figure out how to loosen and tighten the tensioner, the belt comes off easily from the top, and the pulley and water pump come off and go on relatively easily. If your new water pump hasa a paper gasket (like SEK) be sure to get it wet so it sticks in place, because you won't be able to see everything you are doing.

• 
  @haywoodseymour62810 ай бұрын

  What size socket did you use?

• 
  @micradocs10 ай бұрын

  It's a certain socket especially for spark plugs, 14mm.

• 
  @nevercanlala914310 ай бұрын

  very nice video, my condensor has small leak aswel unfortunatly. this will certainly help me replacing it! many thanks!

• 
  @Rabi_Burud10 ай бұрын

  Belt size?

• 
  @micradocs10 ай бұрын

  1165mm it's slightly longer because it this vehicle has AC.

• 
  @erkkihamalainen57258 ай бұрын

  1170 mm also at market, will do CR12DE engine with ac

• 
  @Rabi_Burud8 ай бұрын

  @@erkkihamalainen5725 bro i have nissan sunny 2015 model diesel. My both bulb high beam is not working any solution? I changed the bulbs and combination switch as well

• 
  @erkkihamalainen57258 ай бұрын

  No idea about electris @@Rabi_Burud

• 
  @VikaniZitha-yb3gd10 ай бұрын

  My car blowing the cold air always

• 
  @Paul-ey1ct11 ай бұрын

  Well explained mate 👍

• 
  @peterwilson5528 Жыл бұрын

  You convinced me to take the car to the mechanic.

• 
  @johnbyrne7229 Жыл бұрын

  Gasket /seal part number ?

• 
  @micradocs Жыл бұрын

  HAG3 is the part number for the ring gasket

• 
  @johnbyrne7229 Жыл бұрын

  @@micradocs can’t find anything with that code . Do u have link . 👍

• 
  @micradocs Жыл бұрын

  @@johnbyrne7229 I went into my local parts shop and ordered one from there so I don't have a link. But I do use this link partsinmotion.co.uk to order a lot of parts, if you type your reg in they will list suitable items for your car

• 
  @onealericcisan805 Жыл бұрын

  there is any air valve id you put out the two water cables for change the plugs? i got a micra year 2016 lgp petrol k13

• 
  @onealericcisan805 Жыл бұрын

  2nd question i not replace the three air conduct intake manifold gasket , it's a problem?

• 
  @micradocs Жыл бұрын

  Make sure to put everything you have removed back to its original position. Or you could experience problems

• 
  @simonbone4 ай бұрын

  No, not a problem. I bought new gaskets (rubber seals) but the old ones appeared to be perfectly fine, and would probably last for many more years.

• 
  @onealericcisan8054 ай бұрын

  @@micradocs problems like? the petrol or lpg gas use is the same i see soo no more air enter in the system so i think i make the right work... but soon i have to give the car to a nissan mechanic for change some important pieces of the engine.... my car have 120.000km so i think it's the time right now, with service rope (not know the right english name); and water pomp included and keep a general eye to brakes and under the car

• 
  @onealericcisan805 Жыл бұрын

  there is any valve for the air if you take out the two water cables? Because my mech for change the plugs remove two water cable but i know the air is an enemy

• 
  @micradocs Жыл бұрын

  I just removed the bolts and moved everything slightly out of the way.

• 
  @jwerk3936 Жыл бұрын

  Thanks for the video, i will be trying to replace the condensor on my micra 2011 k13 with help of this video. If you have any tips (not mentioned in this video) i would love to hear :). Thanks!

• 
  @micradocs Жыл бұрын

  Many thanks. The only extra tips I have is to take your time, it should go smoothly, and as long as your bolts are easily removed then the hard part is done. Also make sure there's no gas in the system, but guessing if you're replacing your unit then it's because the gas has all leaked out. Let me know how you get on!

• 
  @jwerk3936 Жыл бұрын

  @@micradocs Thanks for the reply. Yes there is no gass in the system left. I will let you know when its done :)

• 
  @philsimpson355610 ай бұрын

  Good video. Just a question, I can’t see it in the video but is the main engine radiator behind the condenser? Sort of sandwiched together.

• 
  @micradocs10 ай бұрын

  @@philsimpson3556 Thanks. And Yes, that is correct, it is sandwiched together.