Bench Dog Studio is where I share my passion for woodworking, creating making, repurposing and reusing. My other passion is creating video games and those videos can be found on KZread at @HungryCatGames.
I just bought the G0959, the cap to the handle pops off and there is a bunch of plastic inside to remove.
@benchdogstudioАй бұрын
I haven't tried removing my cap but I think I will give it a try now. Thanks!
@russharden4374Ай бұрын
No problem, loving mine so far. The jointer was perfectly coplaner out of the box, but I do get some snipe when planing.
@Uglidan3073 ай бұрын
This was the perfect review for me, I am considering it just for the jointer capacity, I have the Dewalt planer, it would probably spend all its time in jointer, still seems a good deal for a 12 inch jointer!
@michaelshelnutt35345 ай бұрын
Any updates on this unit? Pros, Cons... overall thoughts? Regrets? Would you buy again, if you could go back knowing what you know now, or would you go a different route? Thank you.
@benchdogstudio5 ай бұрын
You can see my other video on the issues I had with the unit in planer mode about 8 months into ownership but I have to saw Grizzly, eventually, did step up and fully resolve the problems. Pretty sure I got back the same unit so I believe they repaired and didn't replace but whatever they did it runs good now. Given my budget I would by this unit again. Now if I could come up with 4-5K I would definitely go another route but at this price point and for the size of my shop and no 220v I still feel this unit is sitting in a sweet spot. The one remaining "con" which isn't really is the noise level. I forgot to put on my ear protection one day while using it for about 10 minute and my ears were literally ringing for about a half hour afterwards. These are noisy machines and there really isn't anything you can do about that. So always remember the PPE and you should be good.
@michaelshafley88096 ай бұрын
Had the same issue with removing the plastic wrap from the handle of my G0940. Seems to me the top cap would come off somehow.
@chaos12919756 ай бұрын
i am about to buy the same machine. but i do wish i would of got it when it was on sale like you did. i ordered the 8 inch version but it was back ordered so i called and they wouldn't be in for a few months. and that was just a we will have a better idea when they would be in in a few months.. so i canceled the order asked if i upgraded if they would give me a discount and it was a no we have no specials on that one lol. so i just hope that the cost difference is worth it. you had a smaller jointer first do you like having the 12 inch modal now? thank you for doing the review you did a great job going over everything.
@benchdogstudio5 ай бұрын
I had a 6 inch "lunch box" style jointer but no planer. I was wanting something larger and this combo machine seemed to be a nice size, two tools in one and price along with the helical head. When I bought it retail price (which I paid) was 999. I believe it has since gone up to 1199. For me the price of a helical planer alone was the better part of the price of this unit so getting an upgrade on my current jointer plus the planer made sense. If you don't have a need to plane or face joint any boards over 8" then you should be fine with that unit but since I already had a 6" I didn't see an 8" as that much improvement so I went to the 12.
@ligngood37876 ай бұрын
This is EXTREMELY helpful, thank you! You really show a lot of the details of how it is built and assembled and answered a lot of my questions. Thanks so much!
@derekcharles35156 ай бұрын
Thanks for the update. I just got the same machine. After a lot of adjusting of the tables, I finally got mine working well. There is planer snipe, however by simply lifting the board ends during infeed and outfeed, I’m able to reduce snipe significantly. The two concerns I have are, will the tables shim adjustments hold over time and what do I do about the funky fence situation. There’s got to be a way to have a fence that can not only slide over more of the cutter but will also slide back far enough for the dust hood in planer mode. Please come up with a fix for that fence and the community will love you. Thanks again for your vids.
@benchdogstudio6 ай бұрын
I find if you tilt the fence back to 45 and slide it as far to the right as possible you can just barely attach the dust hood without needing to remove the fence. But it is a tight fit. Agreed there should be some type of quick release on the fence or a modification to the dust hood so it fits with the fence still on. This design is a "generic" one that a handful of other machine makers are using for 8 and 12" models. CuisinAid, Entcook and Vevor have very similar structured units in the 8" size with the Vevor one showing a very different hood design although it appears to leave some of the cutter exposed! The Jet unit also looks to be from the same design specs too but a few quick searches didn't yield and pics of their dust hood design.
@AaronGeller4 ай бұрын
What did you mean by "will the tables shim adjustments hold over time"?
@derekcharles35154 ай бұрын
First, these are lightweight aluminum tables and could warp over time as cast iron may. Also, the shims are very small and in precarious positions and could move with all the vibration, although once adjusted, I won’t be moving the tables up or down.
@Trooper2667 ай бұрын
Thank you for the video. I live in the Netherlands and have recently purchased a 12-inch planer combo from a Dutch vendor called HBM. It appears to be the same machine as yours, but it lacks the spiral cutters. The Grizzly manual looks much better, I think that I will be using it instead 😅
@ibitaRaptor7 ай бұрын
Hows it holding up after a few months? Would you buy this again?
@benchdogstudio7 ай бұрын
Working just fine. No issues. I'd definitely get one again if I ever needed a second. Collecting chips off my jointer/planer has been great with the only cleaning being what the tool itself didn't send out the dust chute to this collector.
@MixingGBP8 ай бұрын
Now that you’ve owned it for a few months, would you buy it again, or any regrets about the purchase? I am struggling to find a decent 8 inch or wider jointer that is $1000 to $2000.
@benchdogstudio7 ай бұрын
As a jointer it's working fine. As I mentioned in the notes the unit was failing in planer mode. After all was said and done I ended up sending it back (on their dime) to Grizzly for repair. I got it back a week later with no communication, no notes if it was fixed or not and at this point it is still a mystery as I have not been able to give it a thorough test yet. I expect to do so and get a new video of this whole experience posted by the end of the year. So, to answer your question fully, check back at the end of the year. But from just the jointer perspective so far it has been a good tool for me. Getting a 12" jointer at this price point really doesn't have any other options that I could find. Would I buy it again for just a jointer function? A definite maybe. Getting a larger floor standing unit might be a better option but the price at least triples. I replaced my old 6" bench top (standard blades) with this unit (12", helical) and from that perspective it is a big jump forward without a major, comparatively, jump in price. I think if it really is fixed then that definitely maybe would shift back to a definite yes as it fits my needs in a price I was able to afford. If the planer mode still has issues and it's relegated to basically just jointer functions then I'd probably lean more towards maybe to no.
@MixingGBP7 ай бұрын
@@benchdogstudio thanks for the detailed reply. So it seems no company has that “go to” jointer without some hiccups in it or some super expensive price.
@benchdogstudio7 ай бұрын
Pretty much. Your next step up in a 12" jumps to the mid $3000s and just goes up from there. I did find a "ForrestWest" model for around $1600 but without the helical cutter. Parts of it look to be taken straight from the Grizzly, other parts look to be their own design. forestwest.us/products/forestwest-bm10416-12-2-5hp-wood-planer-jointer-combo
@genericuser42668 ай бұрын
I have a G0958 and the feed rollers disintegrated after about 4 hours of combined jointer/planer use. Probably feed less than 100 linear feet through the planer. 4 hours of working time for $550. Silly me for trying to save some shop space. On the bright side, you can make a better decision and not buy this product. Back in the day Grizzly used to make good equipment. Based on this product it seems like maybe they no longer do. Which is a real shame.
@benchdogstudio7 ай бұрын
What did Grizzly say about fix it, assuming still under warranty? I have found their tech support to be pretty responsive although still unknown if my unit is actually fully working or not yet (haven't had time/weather cooperate to give it thorough test yet).
@benchdogstudio5 ай бұрын
@@Upsiderightdown They did fix it and it's has worked great since. Pretty sure I just got a "bad" one and I don't hold it against them as they did work with me quite a bit to try to resolve the issue without shipping it to them but eventually agreed they need to look at it so paid for it to be sent back. I did do a lot of work with it after getting it back and have had zero issues since. Still a decent tool for the money. If that other viewer just wants to complain and not get it fixed under warranty... well I can't really see any advantage to that approach.
@petermacander50399 ай бұрын
Lots of problems with this video. Looks like you could use some help with program design and videophotography in future video making. Lots of wasted time and showing things the viewer doesn't need to see (like you reading instructions which should have been read before making this video) on this 26-1/2 minute l o n g video. Get to the point! Your presentation could have been made more succinctly in half the time.
@benchdogstudio9 ай бұрын
Thanks for the feedback.
@AaronGeller8 ай бұрын
Maybe he can refund you the money you paid to view this video... wait, it was free....
@waltdv3 ай бұрын
You're not wrong, but you bedside manner could use a touch-up, or as you put it, 'could use some help'.
@tonyg6103Ай бұрын
Not a bad video really. I enjoyed watching it without the drama and unnecessary graphics, cutaways, etc. Very thorough presentation. All this convinces me that you absolutely cannot do a video any better yourself.
@robertalbrecht149310 ай бұрын
Did you try the planer? Dr
@benchdogstudio10 ай бұрын
After some back and forth with Grizzly where I sent pics and even some videos they are pretty confident in what is wrong and sent me the parts. Hoping to install in the next few days and try again. So far their customer service has been quite good.
@ENZIO9010 ай бұрын
I THOUGHT THESE WERE NOT ALLOWED IN THE USA. CONSIDERED TO BE TO DANGEROUS .
@benchdogstudio10 ай бұрын
Planers? Jointer? or Combo machines? All three have always been sold here as long as I can remember (which is a number of decades).
@ENZIO9010 ай бұрын
@benchdogstudio combo machine I believe are said to be illegal in the states. They are considered very unsafe. Not 100% sure about that.
@benchdogstudio10 ай бұрын
@@ENZIO90 Definitely not illegal. You wouldn't be able to buy if they were. A number of vendors besides Grizzly all sell them here.
@kevincinnamontoast36699 ай бұрын
You can buy an ak-47 in America. You can shoot your dado blades with an ak-47.
@waltdv3 ай бұрын
@@ENZIO90 We can resolve your uncertainty, no prohibitions.
@brianbarney188510 ай бұрын
Excellent video, I had considered buying one of these but fortunately found a good 10 year old Hammer A31 for $1000.00 instead. It takes a lot less fiddling to switch between planer and jointer but also takes up a lot more room. This machine seems a good alternative to the DeWalt and a benchtop jointer.
@benchdogstudio10 ай бұрын
For that price I probably would have gone that route too! But unfortunately I couldn't afford a new one.
@phillamoore15710 ай бұрын
How were you treated by Grizzly. I've come to learn that ALL brands can potentially take a dump. Nothing, I don't care who the manufacturer is, is made with quality parts anymore. So, customer service, and warranty are huge in my book. So, I'm very interested in seeing how Grizzly treated you. I'm very seriously considering one of their combos.
@benchdogstudio10 ай бұрын
I'm still going back and forth with support. I won't say it is adversarial but more collaborative at this point. They have not seen something like this before (as they claim) and it's looking like one of the gears inside has a bent tooth which appears to be causing the issues. Hopefully in a few more days I'll have a more definitive response. So far I can say I'm satisfied with their communications on the issue but as to a possible resolution, that will take a few more days.
@phillamoore15710 ай бұрын
@@benchdogstudio Well…I guess its’ good that, they’e communicating well with you. But, my hopes were that they got you a new unit, and sent you an RMA/Box to return the old one. Sounds like they’re trying to isolate the problem and just fix that one part, which I’m not a huge fan of. Simply because, now you’re wondering what else might go bad. Please keep us posted on what they do to resolve this for you. I’m thinking of going with the semi-pro model that’s pushing $4K, but that’s a lot of money to me. So, I won’t do it if they don’t take care of you, whether they’ve “seen this before” or not. As far as I’m concerned, if this is a unique situation, then it’s all the more reason for them to take care of you, and get you a knew unit (assuming that would satisfy you). Thanks for the reply. Depending on how they treat you, I might go with a Rikon who (from what I saw) has 5yr warranties on their machines.
@benchdogstudio10 ай бұрын
@@phillamoore157 Give the weight and that this comes by truck on a pallet if I can fix it locally I'd actually prefer that over having to find a pallet and box to return it but if they wanted to send me a new one without needing the old one back (or use the new materials to return the old).... I wouldn't object. Either way I'll put more boards through the repair/replace unit to ensure it really is working as expected.
@phillamoore15710 ай бұрын
@@benchdogstudio That makes sense... Definitely keep us in the loop on how they handle this. And, good luck with it.
@wooddogg87 ай бұрын
@@phillamoore157 I have the 8" version and the blade guard suddenly stopped closing. It's plastic with a flat spot that the spring pushes against to close it. I called customer support, explained the situation and had replacement parts in about 4 days. I consider that good customer service but now I'm a little sketchy on the plastic. hopefully this was a fluke, or pre- existing crack in the plastic that let go after, maybe 4 hrs of run time. Time will tell but overall I'm impressed with the machine
@user-dg2cd9jw6l10 ай бұрын
Hello there sir im Richard III m a filipino. I also love carpentry job n im planing 2 buy also that kind of machine any idea i would be cost here in the Philippines thank you sir😊
@benchdogstudio10 ай бұрын
Sorry, I don't know if it is available there, could be shipped there or what the exchange rate would be. You'd have to contact Grizzly for that information.
@reaper06067011 ай бұрын
This is a beautiful piece my friend.. U work like a guy who has been woodworking for a long time. I love the amount of skill u used to make it. It may not seem like a lot to some ppl out here on YT but I loved watching this video. I wish I had taken up woodworking before my Dad had passed away in 2018 but I hadn't. He would've loved coming out to my workshop with me. That I know bcos he was always very hands on in our family home back in the day. He built everything like wardrobes, Beds, etc. He wasn't a trained carpenter but he could build anything with his hands. He was a jack of all trades, Master of none as he used to say.. LOL Just want to send kindest regards to and ur family my friend. I very much enjoyed this video and the music playing in the background. I only found ur channel from watching @STUMPY NUBS CHANNEL. Ur channel popped up so I clicked on the GRIZZLY Jointer/Thicknesser. I own a smaller version of a similar brand but mine only cost 200 Euros to buy, and even though It doesn't have the Helical cutter it works fine for my needs. I love the combination of Maple and Walnut. Is that Maple that u used for the main body of the box? I love the look of this wood. I struggle to find any of these woods in my area in Ireland. I love watching the finish being put on wood like MAPLE & WALNUT. I hope u keep putting out more content my friend. I checked ur content. Are u relatively new to YT videos? Keep up the great work man. I sub'd to the channel and liked ur videos. Take care man and keep doing ur thing. I'll be watching for more content.
@benchdogstudio11 ай бұрын
Thanks for the kind comments. My dad wasn't really a workshop kind of guy but he was always interested in the stuff I was building and I could feel the pride he felt about what I was making. I've always enjoyed demonstrating, teaching and mentoring things I do to others who are interested which is why I took my woodworking to the next step and started this channel. You are correct that is maple and walnut. Both are plentiful here in the States but highly figure maple like I used is a rarity. I had actually tried a number of finishes on a scrap piece including epoxy which gave it a great deep glossy look but ultimately for this project that wasn't what I was looking for and eventually settled on the shellac to give me what I wanted.
@cerberus288111 ай бұрын
Wish I hadn't bought the GO940 now! Two heads are better than one right!
@jameshamontree4036 Жыл бұрын
Just unboxing mine right this minute looking for a couple of tips on getting going. Thank you for your warning about the plastic on/in the crank. Knowing in advance staved off my own irritation and I used my trusty pocket knife to trim the plastic away cleanly. Thank tremendously for including the bit about the dust collector “free hanging” in jointer mode. That had me stumped.
@kevinwyatt24311 ай бұрын
I have had this same unit for about 6 months. It is not obvious, but the top of the crank nob unscrews so you can remove the plastic and then screw it back on. It's a lot cleaner than trimming the plastic away.
@benchdogstudio7 ай бұрын
Just noticed this comment... I'll have to check for that. Would have made it a lot easier! Thanks!
@bearcat2k Жыл бұрын
Is there a way to adjust the infeed and outfeed tables? I am concerned about the tables moving out of co-planer over time, but I can't tell how this could be restored from any of the videos I've seen on this device. Thanks in advance.
@benchdogstudio Жыл бұрын
@bearcat2k At 20:20 in the video I flip through the manual pages for the various adjustments that are possible (or at least documented by Grizzly) and this adjustment isn't one that is listed. Pause and you can see the section titles. At 22:41 just blow the outfeed table on an angle there are a couple of threads sticking up with nuts on them. This is located on both sides (front and back) and on both infeed and outfeed. In looking over the unit this appears to be how they are connected to the main body. Now this is only a guess on my part, but I think you could loosen these nuts and perhaps shift it a bit one way or another or perhaps shim under one or both studs to subtlely change the tilt of a table. Since mine is acceptable enough from the factory I haven't had reason to touch these. If it ever gets out of alignment then I might be willing to experiment with these.
@shepconsulting Жыл бұрын
Great review. When converting from a jointer to a planer, can you simply slide the fence down to the right or are you forced to bevel the fence away along with sliding it? I would rarely use a bevel cut and it would be nice to keep the fence set a 90 degrees when converting between the two modes. In other reviews, I've noticed that you may be able to simply slide the fence to the right before moving the dust stroud. I'm really considering the purchase of this device instead of buying a Dewalt 735X and a desktop jointer. My shop space is limited, so the combo feature is nice.
@benchdogstudio Жыл бұрын
The fence is probably one of the weaknesses in design but not enough for me to consider it an issue. It either has to be removed or tilted all the way back to have just barely enough clearance for the hood to connect. The manual actually suggests removing it but there is just barely enough clearance to not have to. Near the end of the video when I do the switch over, the position I had it in is where you need to move it to.
@shepconsulting Жыл бұрын
@@benchdogstudio thanks for the clarification.
@kevinwyatt24311 ай бұрын
I have had this same unit for about 6 months. You can tilt the fence and loosen the 4 wing nuts to slide it down and mostly out of the way. The dust collector will attach on top so you can use the unit, but there is a thumb screw to fasten it to the middle of the table, but you cannot align it with the fence still attached. I have run it that way just fine, but it does reduce the dust collection. If you remove the fence, you can tighten down the thumb screw, but I'm not sure it is worth the hassle of taking the fence on and off every time you switch modes.
Пікірлер
I just bought the G0959, the cap to the handle pops off and there is a bunch of plastic inside to remove.
I haven't tried removing my cap but I think I will give it a try now. Thanks!
No problem, loving mine so far. The jointer was perfectly coplaner out of the box, but I do get some snipe when planing.
This was the perfect review for me, I am considering it just for the jointer capacity, I have the Dewalt planer, it would probably spend all its time in jointer, still seems a good deal for a 12 inch jointer!
Any updates on this unit? Pros, Cons... overall thoughts? Regrets? Would you buy again, if you could go back knowing what you know now, or would you go a different route? Thank you.
You can see my other video on the issues I had with the unit in planer mode about 8 months into ownership but I have to saw Grizzly, eventually, did step up and fully resolve the problems. Pretty sure I got back the same unit so I believe they repaired and didn't replace but whatever they did it runs good now. Given my budget I would by this unit again. Now if I could come up with 4-5K I would definitely go another route but at this price point and for the size of my shop and no 220v I still feel this unit is sitting in a sweet spot. The one remaining "con" which isn't really is the noise level. I forgot to put on my ear protection one day while using it for about 10 minute and my ears were literally ringing for about a half hour afterwards. These are noisy machines and there really isn't anything you can do about that. So always remember the PPE and you should be good.
Had the same issue with removing the plastic wrap from the handle of my G0940. Seems to me the top cap would come off somehow.
i am about to buy the same machine. but i do wish i would of got it when it was on sale like you did. i ordered the 8 inch version but it was back ordered so i called and they wouldn't be in for a few months. and that was just a we will have a better idea when they would be in in a few months.. so i canceled the order asked if i upgraded if they would give me a discount and it was a no we have no specials on that one lol. so i just hope that the cost difference is worth it. you had a smaller jointer first do you like having the 12 inch modal now? thank you for doing the review you did a great job going over everything.
I had a 6 inch "lunch box" style jointer but no planer. I was wanting something larger and this combo machine seemed to be a nice size, two tools in one and price along with the helical head. When I bought it retail price (which I paid) was 999. I believe it has since gone up to 1199. For me the price of a helical planer alone was the better part of the price of this unit so getting an upgrade on my current jointer plus the planer made sense. If you don't have a need to plane or face joint any boards over 8" then you should be fine with that unit but since I already had a 6" I didn't see an 8" as that much improvement so I went to the 12.
This is EXTREMELY helpful, thank you! You really show a lot of the details of how it is built and assembled and answered a lot of my questions. Thanks so much!
Thanks for the update. I just got the same machine. After a lot of adjusting of the tables, I finally got mine working well. There is planer snipe, however by simply lifting the board ends during infeed and outfeed, I’m able to reduce snipe significantly. The two concerns I have are, will the tables shim adjustments hold over time and what do I do about the funky fence situation. There’s got to be a way to have a fence that can not only slide over more of the cutter but will also slide back far enough for the dust hood in planer mode. Please come up with a fix for that fence and the community will love you. Thanks again for your vids.
I find if you tilt the fence back to 45 and slide it as far to the right as possible you can just barely attach the dust hood without needing to remove the fence. But it is a tight fit. Agreed there should be some type of quick release on the fence or a modification to the dust hood so it fits with the fence still on. This design is a "generic" one that a handful of other machine makers are using for 8 and 12" models. CuisinAid, Entcook and Vevor have very similar structured units in the 8" size with the Vevor one showing a very different hood design although it appears to leave some of the cutter exposed! The Jet unit also looks to be from the same design specs too but a few quick searches didn't yield and pics of their dust hood design.
What did you mean by "will the tables shim adjustments hold over time"?
First, these are lightweight aluminum tables and could warp over time as cast iron may. Also, the shims are very small and in precarious positions and could move with all the vibration, although once adjusted, I won’t be moving the tables up or down.
Thank you for the video. I live in the Netherlands and have recently purchased a 12-inch planer combo from a Dutch vendor called HBM. It appears to be the same machine as yours, but it lacks the spiral cutters. The Grizzly manual looks much better, I think that I will be using it instead 😅
Hows it holding up after a few months? Would you buy this again?
Working just fine. No issues. I'd definitely get one again if I ever needed a second. Collecting chips off my jointer/planer has been great with the only cleaning being what the tool itself didn't send out the dust chute to this collector.
Now that you’ve owned it for a few months, would you buy it again, or any regrets about the purchase? I am struggling to find a decent 8 inch or wider jointer that is $1000 to $2000.
As a jointer it's working fine. As I mentioned in the notes the unit was failing in planer mode. After all was said and done I ended up sending it back (on their dime) to Grizzly for repair. I got it back a week later with no communication, no notes if it was fixed or not and at this point it is still a mystery as I have not been able to give it a thorough test yet. I expect to do so and get a new video of this whole experience posted by the end of the year. So, to answer your question fully, check back at the end of the year. But from just the jointer perspective so far it has been a good tool for me. Getting a 12" jointer at this price point really doesn't have any other options that I could find. Would I buy it again for just a jointer function? A definite maybe. Getting a larger floor standing unit might be a better option but the price at least triples. I replaced my old 6" bench top (standard blades) with this unit (12", helical) and from that perspective it is a big jump forward without a major, comparatively, jump in price. I think if it really is fixed then that definitely maybe would shift back to a definite yes as it fits my needs in a price I was able to afford. If the planer mode still has issues and it's relegated to basically just jointer functions then I'd probably lean more towards maybe to no.
@@benchdogstudio thanks for the detailed reply. So it seems no company has that “go to” jointer without some hiccups in it or some super expensive price.
Pretty much. Your next step up in a 12" jumps to the mid $3000s and just goes up from there. I did find a "ForrestWest" model for around $1600 but without the helical cutter. Parts of it look to be taken straight from the Grizzly, other parts look to be their own design. forestwest.us/products/forestwest-bm10416-12-2-5hp-wood-planer-jointer-combo
I have a G0958 and the feed rollers disintegrated after about 4 hours of combined jointer/planer use. Probably feed less than 100 linear feet through the planer. 4 hours of working time for $550. Silly me for trying to save some shop space. On the bright side, you can make a better decision and not buy this product. Back in the day Grizzly used to make good equipment. Based on this product it seems like maybe they no longer do. Which is a real shame.
What did Grizzly say about fix it, assuming still under warranty? I have found their tech support to be pretty responsive although still unknown if my unit is actually fully working or not yet (haven't had time/weather cooperate to give it thorough test yet).
@@Upsiderightdown They did fix it and it's has worked great since. Pretty sure I just got a "bad" one and I don't hold it against them as they did work with me quite a bit to try to resolve the issue without shipping it to them but eventually agreed they need to look at it so paid for it to be sent back. I did do a lot of work with it after getting it back and have had zero issues since. Still a decent tool for the money. If that other viewer just wants to complain and not get it fixed under warranty... well I can't really see any advantage to that approach.
Lots of problems with this video. Looks like you could use some help with program design and videophotography in future video making. Lots of wasted time and showing things the viewer doesn't need to see (like you reading instructions which should have been read before making this video) on this 26-1/2 minute l o n g video. Get to the point! Your presentation could have been made more succinctly in half the time.
Thanks for the feedback.
Maybe he can refund you the money you paid to view this video... wait, it was free....
You're not wrong, but you bedside manner could use a touch-up, or as you put it, 'could use some help'.
Not a bad video really. I enjoyed watching it without the drama and unnecessary graphics, cutaways, etc. Very thorough presentation. All this convinces me that you absolutely cannot do a video any better yourself.
Did you try the planer? Dr
After some back and forth with Grizzly where I sent pics and even some videos they are pretty confident in what is wrong and sent me the parts. Hoping to install in the next few days and try again. So far their customer service has been quite good.
I THOUGHT THESE WERE NOT ALLOWED IN THE USA. CONSIDERED TO BE TO DANGEROUS .
Planers? Jointer? or Combo machines? All three have always been sold here as long as I can remember (which is a number of decades).
@benchdogstudio combo machine I believe are said to be illegal in the states. They are considered very unsafe. Not 100% sure about that.
@@ENZIO90 Definitely not illegal. You wouldn't be able to buy if they were. A number of vendors besides Grizzly all sell them here.
You can buy an ak-47 in America. You can shoot your dado blades with an ak-47.
@@ENZIO90 We can resolve your uncertainty, no prohibitions.
Excellent video, I had considered buying one of these but fortunately found a good 10 year old Hammer A31 for $1000.00 instead. It takes a lot less fiddling to switch between planer and jointer but also takes up a lot more room. This machine seems a good alternative to the DeWalt and a benchtop jointer.
For that price I probably would have gone that route too! But unfortunately I couldn't afford a new one.
How were you treated by Grizzly. I've come to learn that ALL brands can potentially take a dump. Nothing, I don't care who the manufacturer is, is made with quality parts anymore. So, customer service, and warranty are huge in my book. So, I'm very interested in seeing how Grizzly treated you. I'm very seriously considering one of their combos.
I'm still going back and forth with support. I won't say it is adversarial but more collaborative at this point. They have not seen something like this before (as they claim) and it's looking like one of the gears inside has a bent tooth which appears to be causing the issues. Hopefully in a few more days I'll have a more definitive response. So far I can say I'm satisfied with their communications on the issue but as to a possible resolution, that will take a few more days.
@@benchdogstudio Well…I guess its’ good that, they’e communicating well with you. But, my hopes were that they got you a new unit, and sent you an RMA/Box to return the old one. Sounds like they’re trying to isolate the problem and just fix that one part, which I’m not a huge fan of. Simply because, now you’re wondering what else might go bad. Please keep us posted on what they do to resolve this for you. I’m thinking of going with the semi-pro model that’s pushing $4K, but that’s a lot of money to me. So, I won’t do it if they don’t take care of you, whether they’ve “seen this before” or not. As far as I’m concerned, if this is a unique situation, then it’s all the more reason for them to take care of you, and get you a knew unit (assuming that would satisfy you). Thanks for the reply. Depending on how they treat you, I might go with a Rikon who (from what I saw) has 5yr warranties on their machines.
@@phillamoore157 Give the weight and that this comes by truck on a pallet if I can fix it locally I'd actually prefer that over having to find a pallet and box to return it but if they wanted to send me a new one without needing the old one back (or use the new materials to return the old).... I wouldn't object. Either way I'll put more boards through the repair/replace unit to ensure it really is working as expected.
@@benchdogstudio That makes sense... Definitely keep us in the loop on how they handle this. And, good luck with it.
@@phillamoore157 I have the 8" version and the blade guard suddenly stopped closing. It's plastic with a flat spot that the spring pushes against to close it. I called customer support, explained the situation and had replacement parts in about 4 days. I consider that good customer service but now I'm a little sketchy on the plastic. hopefully this was a fluke, or pre- existing crack in the plastic that let go after, maybe 4 hrs of run time. Time will tell but overall I'm impressed with the machine
Hello there sir im Richard III m a filipino. I also love carpentry job n im planing 2 buy also that kind of machine any idea i would be cost here in the Philippines thank you sir😊
Sorry, I don't know if it is available there, could be shipped there or what the exchange rate would be. You'd have to contact Grizzly for that information.
This is a beautiful piece my friend.. U work like a guy who has been woodworking for a long time. I love the amount of skill u used to make it. It may not seem like a lot to some ppl out here on YT but I loved watching this video. I wish I had taken up woodworking before my Dad had passed away in 2018 but I hadn't. He would've loved coming out to my workshop with me. That I know bcos he was always very hands on in our family home back in the day. He built everything like wardrobes, Beds, etc. He wasn't a trained carpenter but he could build anything with his hands. He was a jack of all trades, Master of none as he used to say.. LOL Just want to send kindest regards to and ur family my friend. I very much enjoyed this video and the music playing in the background. I only found ur channel from watching @STUMPY NUBS CHANNEL. Ur channel popped up so I clicked on the GRIZZLY Jointer/Thicknesser. I own a smaller version of a similar brand but mine only cost 200 Euros to buy, and even though It doesn't have the Helical cutter it works fine for my needs. I love the combination of Maple and Walnut. Is that Maple that u used for the main body of the box? I love the look of this wood. I struggle to find any of these woods in my area in Ireland. I love watching the finish being put on wood like MAPLE & WALNUT. I hope u keep putting out more content my friend. I checked ur content. Are u relatively new to YT videos? Keep up the great work man. I sub'd to the channel and liked ur videos. Take care man and keep doing ur thing. I'll be watching for more content.
Thanks for the kind comments. My dad wasn't really a workshop kind of guy but he was always interested in the stuff I was building and I could feel the pride he felt about what I was making. I've always enjoyed demonstrating, teaching and mentoring things I do to others who are interested which is why I took my woodworking to the next step and started this channel. You are correct that is maple and walnut. Both are plentiful here in the States but highly figure maple like I used is a rarity. I had actually tried a number of finishes on a scrap piece including epoxy which gave it a great deep glossy look but ultimately for this project that wasn't what I was looking for and eventually settled on the shellac to give me what I wanted.
Wish I hadn't bought the GO940 now! Two heads are better than one right!
Just unboxing mine right this minute looking for a couple of tips on getting going. Thank you for your warning about the plastic on/in the crank. Knowing in advance staved off my own irritation and I used my trusty pocket knife to trim the plastic away cleanly. Thank tremendously for including the bit about the dust collector “free hanging” in jointer mode. That had me stumped.
I have had this same unit for about 6 months. It is not obvious, but the top of the crank nob unscrews so you can remove the plastic and then screw it back on. It's a lot cleaner than trimming the plastic away.
Just noticed this comment... I'll have to check for that. Would have made it a lot easier! Thanks!
Is there a way to adjust the infeed and outfeed tables? I am concerned about the tables moving out of co-planer over time, but I can't tell how this could be restored from any of the videos I've seen on this device. Thanks in advance.
@bearcat2k At 20:20 in the video I flip through the manual pages for the various adjustments that are possible (or at least documented by Grizzly) and this adjustment isn't one that is listed. Pause and you can see the section titles. At 22:41 just blow the outfeed table on an angle there are a couple of threads sticking up with nuts on them. This is located on both sides (front and back) and on both infeed and outfeed. In looking over the unit this appears to be how they are connected to the main body. Now this is only a guess on my part, but I think you could loosen these nuts and perhaps shift it a bit one way or another or perhaps shim under one or both studs to subtlely change the tilt of a table. Since mine is acceptable enough from the factory I haven't had reason to touch these. If it ever gets out of alignment then I might be willing to experiment with these.
Great review. When converting from a jointer to a planer, can you simply slide the fence down to the right or are you forced to bevel the fence away along with sliding it? I would rarely use a bevel cut and it would be nice to keep the fence set a 90 degrees when converting between the two modes. In other reviews, I've noticed that you may be able to simply slide the fence to the right before moving the dust stroud. I'm really considering the purchase of this device instead of buying a Dewalt 735X and a desktop jointer. My shop space is limited, so the combo feature is nice.
The fence is probably one of the weaknesses in design but not enough for me to consider it an issue. It either has to be removed or tilted all the way back to have just barely enough clearance for the hood to connect. The manual actually suggests removing it but there is just barely enough clearance to not have to. Near the end of the video when I do the switch over, the position I had it in is where you need to move it to.
@@benchdogstudio thanks for the clarification.
I have had this same unit for about 6 months. You can tilt the fence and loosen the 4 wing nuts to slide it down and mostly out of the way. The dust collector will attach on top so you can use the unit, but there is a thumb screw to fasten it to the middle of the table, but you cannot align it with the fence still attached. I have run it that way just fine, but it does reduce the dust collection. If you remove the fence, you can tighten down the thumb screw, but I'm not sure it is worth the hassle of taking the fence on and off every time you switch modes.