Hello! I have the time and money to build a setup- can you share any details? What does your control box control? Any diagrams or schematics? Your system is magnificent! It’s a life-long dream of mine to build a laminar flow fountain! :)
@magicmastera2 күн бұрын
Hi, Thank you. its long ago 15 Jears. If you can send me your email address i will send you the informations you need. you can delete the address aftrwords in your post. thanx.
@kristahunter30052 күн бұрын
Thank you so much!! I am excited to get started. Your fountain is still the best one!
@user-iq2dn7jm2u2 ай бұрын
Hi
@user-un2he8nf4w4 ай бұрын
Very cool please PM me more info
@rikilshah2 жыл бұрын
Hey, Great Setup. Could give brief idea about Laminar Jet cutter working mechanism? Thanks in advance.
@magicmastera2 жыл бұрын
Thanx. Need your mail address ...
@leepu7473 жыл бұрын
Dear Sir I tried for leminar nozzle, but after some distance water spread. I want to know about LOW PASS FILTER. is top & bottom empty space are play a role of LOW PASS FILTER. what is air tank before leminar nozzle? Dear Sir I also tried for laminar, up to a extend I successes, but after a distance water spread. I use 4" dia pipe and 10" long and water jet hole is 12mm. pump is 18 meter head and discharge 6480 lph. I need water flow rate and pump specification
@magicmastera3 жыл бұрын
The low pass filter is eliminating the Pump Jitter. Its nothing more than a air thight thank, the beigger the better, water inlet is about on a third of the lenght, out bottom, the natural air inside will balance the water pressure. My one is about 600mm high, 200mm diameter or similar. Good luck
@leepu7473 жыл бұрын
@@magicmastera Thanks a lot, very informative. I appreciate, if you can send sketch of air tank. If you feel comfortable, I would like to share whatsapp number, to discuss more. +919828533325 Thanks n regards
@chifordenis3 жыл бұрын
what do you do at winter? It froze and damage it?🐂👨🏿🦽❄❄
@magicmastera3 жыл бұрын
Hi Denis, the parts are all removeble. The whole nozzle construction. Just the High quality epoxy fiber glass box that holds the electronics inside, is outside the whole year. It still works, after 12 Years.
@chifordenis3 жыл бұрын
@@magicmastera i want to build one too in my garden. From where can I find a tutorial building this. Did you made it yourself or just yo bought from somewhere? It will be very helpful if I have a tutorial building it.🐂
@magicmastera3 жыл бұрын
Shure? its a lot of work. Its not a weekend Project. You will be working over Months. I did not had any plans All by my self.. But if you like, i can bring you the soluition to it. Just contact me by email or publish you mail addres in a reply, you can delete it aftrwords.
@chifordenis3 жыл бұрын
@@magicmastera sure that would be very helpful. I've seen a lot of videos about laminar flow. I have seen from smarter everyday and from action lab how they do it. I know only the science behind laminar flow, but not the building part. I am 17 yo and i want to make a corner from my backyard more interesting. 🐂🐂
@magicmastera3 жыл бұрын
@@chifordenis Send me a mail or post yours here.
@93560793 жыл бұрын
Nice 👍
@pacificswimmingpools74143 жыл бұрын
Great Boss, its a different joy and aspect of life that doing something you like and becoming successful in it.Hats off to you
@portamentouk3 жыл бұрын
I think some of the links in the description are down, could you update if possible? Or if not, isa there any equipment which can do this out there at the monet? Thanks
@magicmastera3 жыл бұрын
I dubble checked the links, they work fine.
@ericlotze77243 жыл бұрын
The KZread Algorhythm Somehow Lead me to This GREAT PROJECT (Only 11 Years Late...)
@ericlotze77243 жыл бұрын
This was all DIY right?
@eduardofarias53973 жыл бұрын
Amazing! How do you get the stream to start and stop so suddenly? And what diameter hole are you using? I'm using a 16000 l/h pump with a 1/2 inch water exit and can't get good enough distance on the stream.
@SurajChauhan-po8ll3 жыл бұрын
❤️❤️❤️Wow, it's look cool. I am hobbyist and I also want to do this. Can you please share, how have you made this, what are the things that are used in construction of this laminar nozzle My mail id is [email protected]
@bholamallah77943 жыл бұрын
Nais
@bogdanvladonica3 жыл бұрын
Is the tank for low pass filter just an empty tube?
@bogdanvladonica3 жыл бұрын
Can you please tell me what is the purpose of the vertical tank/tube with the two hoses inside it behind the laminar nozzle?
@magicmastera3 жыл бұрын
Bogdan Vlad Onica: this is a low pass filter. You need it to avoid the pump jitter, this holds the water pressure constant. The biger the filter the better the water pressure. Yes its just an empti airtight tank with in and outlet. Bottom in and about 1/3 higher the out. The air that is naturally in the tank will act like a spring. It will control the flow perfectly.
@marionwaskonig79973 жыл бұрын
Hello I hope you are still working here on youtube? I come from Germany and have also learned a lot about jamping jets. I myself also have some. Maybe you would like to exchange ideas with me. I would be very happy to receive your answer. email address is [email protected] many thanks greeting
@chrisbanziger88164 жыл бұрын
Hello You explained in another video the use of a stepper motor. In this video you use a stepper and i see also the copper wiring of a solonoide. Are both used for the cutter? Who is doing what? Could you explain please. Chris
@magicmastera4 жыл бұрын
Hi, i tested both. I finally used the stepper motor as a cutter for the laminar stream, its faster and less vibration, thats verry important. if you can publish a mail addess i can send you the whole solution. Good Luck
@johnnyuppal78784 жыл бұрын
You could be in trouble in England if you was to tell a man he has a nice pair of knockers !
@ebidel5615 жыл бұрын
I do not know how to interrupt the training. Thank you
@magicmastera5 жыл бұрын
ebi del please watch my other videos
@ebidel5615 жыл бұрын
Hi💐how to make
@shavinmccrotch94355 жыл бұрын
"...see how it looks." or "...see what it looks like." Never "...see how it looks like." Basic English No charge You’re welcome
@angelopalmieri4345 жыл бұрын
Excellent work
@sramirez3665 жыл бұрын
hi buddy awesom work.you could help me with information I am in construction of this for my garden you can send me information on how you built the nozzle?the pump used since thank you very much [email protected]
@AlphaOmega5 жыл бұрын
what song in this video ?
@magicmastera5 жыл бұрын
Its a stock one from Pinaccle i beleve, too long ago. Sorry.
@AlphaOmega5 жыл бұрын
@@magicmastera what Pinaccle ? i really love it T_T
@magicmastera5 жыл бұрын
Sorry wrong, its called: Pinnacle Studio, Google it ...
@AlphaOmega5 жыл бұрын
@@magicmastera thankyou . i'll try
@yogaalayam68385 жыл бұрын
what hp motor connected friend
@satyanpatel64035 жыл бұрын
I just found this video, and am so glad I did. I plan on using the rim shot trigger from TR 8 to the device you made to on my Korg SQ-1 to trigger in. Has anything changed since this video was last updated? Same parts, same Arduino Uno? I plan on ordering soon. Thank you in advance.
@magicmastera5 жыл бұрын
Satyan Patel: Hi. You can use a arduino micro or uno. Just follow the directions described in the File. My one works since many years like a charm. No problems detected. Good luck.
@satyanpatel64035 жыл бұрын
You sir, are very talented! Thanks! I have a SH 101 with no sequencer in my Roland System 1. A 'Plug in" as Roland calls it.
@satyanpatel64035 жыл бұрын
@@magicmastera sir, I was searching and found the Bastl Klik which does exactly what your device does, but it does it via USB 5v power. Total cost is 49.00. I'm still hoping to use it with the Korg SQ-1 sync in. Knowing Korg they don't exactly follow the midi rules.
@magicmastera5 жыл бұрын
Hi, cool, yes this will work too.
@zackwrightmusic5 жыл бұрын
I was finally able to get this to work - not sure what the issue was before. Thanks again for making these plans!
@magicmastera5 жыл бұрын
Ohh cool! Congratulation. I am glad you get it to work. Have Fun
@acousticlover-datnguyen65716 жыл бұрын
I wish i can make it.
@monkdoom56996 жыл бұрын
amazing! i guess it will work on Juno 60 .
@magicmastera6 жыл бұрын
Hi, i am not 100% shure, Roland used also a 10V Triggers in older machines i guess. You have to google this to be shure. You can easy set a higher trigger, you only need a resistor and a transistor on the outpt of the arduino and a 10V supply. Maybe the Juno 60 will also work with the 5V trigger. good luck. My solution is very easy and cost not more than 15 $.
@monkdoom56996 жыл бұрын
Well the roland tr 707 have a trigger output (rim shot +5v 20ms) and i ve seen on videos it works great . So if i purchase the andruino uno thing ,how i do connect it ? i saw the Schematic ,but i am not really deep on electronic stuff . i guess i ll have to do some hand wiring.
@sanjacob6 жыл бұрын
i will test it in the next few days and give you a feedback tr8 triggering>juno60arp
@steun866 жыл бұрын
Thanks, it's working with my arduino uno!
@nightwing36s6 жыл бұрын
This is absolutely beautiful. Do you have a build log or any information on how you built the nozzle?
@magicmastera6 жыл бұрын
thank you. if you send me your mail address, i can send you the informations you need.
@manuwaikorber16846 жыл бұрын
Could I please grab a copy of the build information too?
@andrew_assis6 жыл бұрын
Nice work buddy, I can also get details of the construction and if possible the code that used in the project! I want to put one in my garden, follow my e-mail: [email protected] Thank you.
@eduardofarias53973 жыл бұрын
@@magicmastera would you send it to [email protected] as well? Much appreciated.
@rhulerII Жыл бұрын
@@magicmastera me too please.
@Sultryhustler_music6 жыл бұрын
With this trigger anything, or just specifically the 101? Thinking about trying it with my tb-03
@sanjacob6 жыл бұрын
hello, are you from switzerland ? gruss aus zh
@magicmastera6 жыл бұрын
Hi, yes you are right, i am from ZH too. I have listen to your channel, cool sound, cool setup, love it. *SMILE*
@sanjacob6 жыл бұрын
hast Du mal zeit für ein treffen. ich würde gerne so einen converter bauen bräuchte aber noch ein wenig infos dazu, bin noch ein technik neuling.
@walterguzmanflores26616 жыл бұрын
hello How is he circuit to use control a PAP motor ??
@zackwrightmusic6 жыл бұрын
Hi, I attempted to build the Arduino Uno version but can't get it to work properly - it triggers some notes but no better than just going directly from the RS output with a boosted signal - drops notes and doesn't play sequences in order. Also the activity LED doesn't light up. Are you positive the schematics are correct? It one comment here you mention needing 4 resistors, but only have 3 on the Arduino schematic. Any idea what might be going wrong? Thanks!
@magicmastera6 жыл бұрын
Hi, i am sorry if you have problems. My one works 100% thight, i never have drops till today. It's 2 years ago, i cant remember how exact i tested it for the Arduino uno, but i tested it and it worked. I can try to run it again and check if there are any problems with the translated arduino uno code. THE PROBLEM: I leve tomorrow for a 3 week vacation, if you can wait, we find a solution. but you need to be patient. sorry. Strange is that the led is not working when you have an output. Please check the wiring and the parts again for now. the code is so simple, input any signal = output 20ms 5V, thats it. Hope you can wait, thanx for your feedback.
@zackwrightmusic6 жыл бұрын
Thanks for your reply! I'll be patient, if you could double check that would be great, thanks very much. I'll post here if I end up getting it working.
@magicmastera6 жыл бұрын
Just give it a try ... Remove all the wires from the board. Use a wire 5V on the arduino board to Aref on the other side, like in the schematics. Whitout that it won't work! Flash the arduino board again with the Xloader, set 115200 boud and use the right com port. After programming ( the LED shoud flicker in a high frequency. Now use a wire to connect the A0 and GND. each time you connect to GND, the Led i going to dark. Yes? Just to be shure your arduino is programmed ok, your board is working. If this works try again the rest. there can be more prblems, but i have no time yet to test again everithing.
@zackwrightmusic6 жыл бұрын
Thanks, just tried this, the LED behaves exactly like you're saying - so I guess the problem is somewhere other than the Arduino..
@zackwrightmusic6 жыл бұрын
These are the components I am using, are these right? I'm a novice with electronics: www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=57bbbecc58
@komal79627 жыл бұрын
easte of time
@mehmetyuksel65237 жыл бұрын
Hi A very good cutter I interested in made this cutter can you give me more data about your design and mechanism? thanks
@magicmastera7 жыл бұрын
need you mail address. thanx.
@brainstein847 жыл бұрын
Hi Magicmastera! I'm wondering if you'd help to build my own kit, In fact I'd like one on both assignable out (A & B). A => would be the RIM B=> would the cowbell work? if yes Is there anything else to program in the Arduino Uno Board? I'm really newbie in programing and custom thing and I also definitely be interested to purchase this kit if you decide to make it.
@csselement7 жыл бұрын
This seems like a good solution, but I wish you'd go into more depth. I have an Arduino and understand how to flash it with the code but how do I go about connecting it to the TR-8 and SH-101? Is the rimshot being sent from one of the assignable outputs? What type of input is on the Arduino and also the output to the SH-101?
@magicmastera7 жыл бұрын
thanx. Just download the File from the description. You find a picture in the arduino Folder where you can see the wiring. Really easy to do. And wirks perfect since one year.
@phunnuocnghethuat33957 жыл бұрын
0947 664 974
@dkblaze90727 жыл бұрын
I've created a laminar system but, it can't emit lights as bright as yours. Can you help?
@magicmastera7 жыл бұрын
Post a mail address, can send you some informations. KZread do kind a not allow anymore writing messages as it seems.
@dkblaze90727 жыл бұрын
My email id is [email protected], I've already mailed you at your email.
@honeydewmelon917 жыл бұрын
Hi :) I'd also like to have some information about it! That would be very kind of you :) [email protected]
@satbirtalwar66027 жыл бұрын
Could you please send me some instructions to build the system and any suggestions on color changer controller? [email protected]
@gordonfleming49066 жыл бұрын
i am aslo having trobule with light, can you send me your infor [email protected]
@prayagraj85547 жыл бұрын
how do you stop water flow in mid way?
@namedisclosed8 жыл бұрын
Hi magicmastera: any chance of a more in depth explanation on how to build this?
@magicmastera8 жыл бұрын
+ryanwellsmusic: Hi, all you need is to DL the Files, read carfully and look at the grafics. You Buy a arduino Uno board and follow the steps. thats the easyest way.
@Expectation2478 жыл бұрын
Please can you put a bass speaker near it and make the flow into a spiral? perhaps the volume of flow is impractiacl because it would need a very powerful sine wave to make it into a wobble laminar flow
@ivan0072308 жыл бұрын
Hey, doesn't tr-8 send all the midi notes from midi out?
@magicmastera8 жыл бұрын
+Ivan Stankov Hi, this has nothing to do with midi, its for syncing old analogue synth's with a 5V Trigger Pulse signal.
@ivan0072308 жыл бұрын
+magicmastera so it cant send sequence to other drum machines? I am going to try it with volca sample.
@abundantharmony8 жыл бұрын
You can tell easily here how blue light reflects and refracts so much better. This is why the ocean and pools look blue. Too cool.
@botany500kojak8 жыл бұрын
I found another solution. Increase the gain of the rim shot to say 150 or 200 and it produces enough to trigger the SH-101 correctly. The standard volume for each inst is set to 100. Look in the manual on how to do it.
@magicmastera8 жыл бұрын
+Botany 500 Wow, hoc clever! I nedd to test it. Thanx.
@magicmastera8 жыл бұрын
+Botany 500 Antother User mentioned that its not working. I tested it yesterday my self, your Idea is definitly not working! It drops so many beats, its not precise, forget it. For me, not a workaround. But thanx for your Input.
@botany500kojak8 жыл бұрын
+magicmastera Yes, you are correct. I should have tried it properly. I just heard it was triggering more notes, and thought it was working. But, like you said it was not precise. I used a 707 with the 101 and the TR-8 sounds nothing like it. I have one question. I am going to make the sync box but I can not find the Attiny 45 (or 85) with 8MHZ. But, I found one with 10MHZ. Would that work too?
@magicmastera8 жыл бұрын
Hi, cool! You build your own! Yes the Atmel 45 or 85 works fine in any MHZ. But you need to programm this chip with my software, need an ISP programmer, you also need to change the mhz in the Fusebits. If you dont know how, it is easyer for you use a "arduino uno board" (about 20$), you can flash it by USB, use the XLoader xloader.russemotto.com/, i can try compile the software for you for the Arduino Uno, this should work fine. Yes, the Arduino Uno board is a bit too Big for this kind of Project, but if you dont have experience with microcontrollers, this is the most easyest way for you. let me know if you want to go this way.
@botany500kojak8 жыл бұрын
+magicmastera Thanks for the response. If I buy the Arduino Uno board will I also need all the parts from the schematic?
@Herpderperder8 жыл бұрын
dork
@botany500kojak8 жыл бұрын
Hi, could you post some photos of what the box looks like inside? and the cable connecting to it? Thanks. I would like to try and make one.
@magicmastera8 жыл бұрын
Hi Peter, sorry i do not produce this parts, it's too much effort for single ones and would cost too much. About 6 - 7 Hours work. In the infos on top you find all the infos in the links to build one yourself. But thank you for your Interest.
Пікірлер
Hello! I have the time and money to build a setup- can you share any details? What does your control box control? Any diagrams or schematics? Your system is magnificent! It’s a life-long dream of mine to build a laminar flow fountain! :)
Hi, Thank you. its long ago 15 Jears. If you can send me your email address i will send you the informations you need. you can delete the address aftrwords in your post. thanx.
Thank you so much!! I am excited to get started. Your fountain is still the best one!
Hi
Very cool please PM me more info
Hey, Great Setup. Could give brief idea about Laminar Jet cutter working mechanism? Thanks in advance.
Thanx. Need your mail address ...
Dear Sir I tried for leminar nozzle, but after some distance water spread. I want to know about LOW PASS FILTER. is top & bottom empty space are play a role of LOW PASS FILTER. what is air tank before leminar nozzle? Dear Sir I also tried for laminar, up to a extend I successes, but after a distance water spread. I use 4" dia pipe and 10" long and water jet hole is 12mm. pump is 18 meter head and discharge 6480 lph. I need water flow rate and pump specification
The low pass filter is eliminating the Pump Jitter. Its nothing more than a air thight thank, the beigger the better, water inlet is about on a third of the lenght, out bottom, the natural air inside will balance the water pressure. My one is about 600mm high, 200mm diameter or similar. Good luck
@@magicmastera Thanks a lot, very informative. I appreciate, if you can send sketch of air tank. If you feel comfortable, I would like to share whatsapp number, to discuss more. +919828533325 Thanks n regards
what do you do at winter? It froze and damage it?🐂👨🏿🦽❄❄
Hi Denis, the parts are all removeble. The whole nozzle construction. Just the High quality epoxy fiber glass box that holds the electronics inside, is outside the whole year. It still works, after 12 Years.
@@magicmastera i want to build one too in my garden. From where can I find a tutorial building this. Did you made it yourself or just yo bought from somewhere? It will be very helpful if I have a tutorial building it.🐂
Shure? its a lot of work. Its not a weekend Project. You will be working over Months. I did not had any plans All by my self.. But if you like, i can bring you the soluition to it. Just contact me by email or publish you mail addres in a reply, you can delete it aftrwords.
@@magicmastera sure that would be very helpful. I've seen a lot of videos about laminar flow. I have seen from smarter everyday and from action lab how they do it. I know only the science behind laminar flow, but not the building part. I am 17 yo and i want to make a corner from my backyard more interesting. 🐂🐂
@@chifordenis Send me a mail or post yours here.
Nice 👍
Great Boss, its a different joy and aspect of life that doing something you like and becoming successful in it.Hats off to you
I think some of the links in the description are down, could you update if possible? Or if not, isa there any equipment which can do this out there at the monet? Thanks
I dubble checked the links, they work fine.
The KZread Algorhythm Somehow Lead me to This GREAT PROJECT (Only 11 Years Late...)
This was all DIY right?
Amazing! How do you get the stream to start and stop so suddenly? And what diameter hole are you using? I'm using a 16000 l/h pump with a 1/2 inch water exit and can't get good enough distance on the stream.
❤️❤️❤️Wow, it's look cool. I am hobbyist and I also want to do this. Can you please share, how have you made this, what are the things that are used in construction of this laminar nozzle My mail id is [email protected]
Nais
Is the tank for low pass filter just an empty tube?
Can you please tell me what is the purpose of the vertical tank/tube with the two hoses inside it behind the laminar nozzle?
Bogdan Vlad Onica: this is a low pass filter. You need it to avoid the pump jitter, this holds the water pressure constant. The biger the filter the better the water pressure. Yes its just an empti airtight tank with in and outlet. Bottom in and about 1/3 higher the out. The air that is naturally in the tank will act like a spring. It will control the flow perfectly.
Hello I hope you are still working here on youtube? I come from Germany and have also learned a lot about jamping jets. I myself also have some. Maybe you would like to exchange ideas with me. I would be very happy to receive your answer. email address is [email protected] many thanks greeting
Hello You explained in another video the use of a stepper motor. In this video you use a stepper and i see also the copper wiring of a solonoide. Are both used for the cutter? Who is doing what? Could you explain please. Chris
Hi, i tested both. I finally used the stepper motor as a cutter for the laminar stream, its faster and less vibration, thats verry important. if you can publish a mail addess i can send you the whole solution. Good Luck
You could be in trouble in England if you was to tell a man he has a nice pair of knockers !
I do not know how to interrupt the training. Thank you
ebi del please watch my other videos
Hi💐how to make
"...see how it looks." or "...see what it looks like." Never "...see how it looks like." Basic English No charge You’re welcome
Excellent work
hi buddy awesom work.you could help me with information I am in construction of this for my garden you can send me information on how you built the nozzle?the pump used since thank you very much [email protected]
what song in this video ?
Its a stock one from Pinaccle i beleve, too long ago. Sorry.
@@magicmastera what Pinaccle ? i really love it T_T
Sorry wrong, its called: Pinnacle Studio, Google it ...
@@magicmastera thankyou . i'll try
what hp motor connected friend
I just found this video, and am so glad I did. I plan on using the rim shot trigger from TR 8 to the device you made to on my Korg SQ-1 to trigger in. Has anything changed since this video was last updated? Same parts, same Arduino Uno? I plan on ordering soon. Thank you in advance.
Satyan Patel: Hi. You can use a arduino micro or uno. Just follow the directions described in the File. My one works since many years like a charm. No problems detected. Good luck.
You sir, are very talented! Thanks! I have a SH 101 with no sequencer in my Roland System 1. A 'Plug in" as Roland calls it.
@@magicmastera sir, I was searching and found the Bastl Klik which does exactly what your device does, but it does it via USB 5v power. Total cost is 49.00. I'm still hoping to use it with the Korg SQ-1 sync in. Knowing Korg they don't exactly follow the midi rules.
Hi, cool, yes this will work too.
I was finally able to get this to work - not sure what the issue was before. Thanks again for making these plans!
Ohh cool! Congratulation. I am glad you get it to work. Have Fun
I wish i can make it.
amazing! i guess it will work on Juno 60 .
Hi, i am not 100% shure, Roland used also a 10V Triggers in older machines i guess. You have to google this to be shure. You can easy set a higher trigger, you only need a resistor and a transistor on the outpt of the arduino and a 10V supply. Maybe the Juno 60 will also work with the 5V trigger. good luck. My solution is very easy and cost not more than 15 $.
Well the roland tr 707 have a trigger output (rim shot +5v 20ms) and i ve seen on videos it works great . So if i purchase the andruino uno thing ,how i do connect it ? i saw the Schematic ,but i am not really deep on electronic stuff . i guess i ll have to do some hand wiring.
i will test it in the next few days and give you a feedback tr8 triggering>juno60arp
Thanks, it's working with my arduino uno!
This is absolutely beautiful. Do you have a build log or any information on how you built the nozzle?
thank you. if you send me your mail address, i can send you the informations you need.
Could I please grab a copy of the build information too?
Nice work buddy, I can also get details of the construction and if possible the code that used in the project! I want to put one in my garden, follow my e-mail: [email protected] Thank you.
@@magicmastera would you send it to [email protected] as well? Much appreciated.
@@magicmastera me too please.
With this trigger anything, or just specifically the 101? Thinking about trying it with my tb-03
hello, are you from switzerland ? gruss aus zh
Hi, yes you are right, i am from ZH too. I have listen to your channel, cool sound, cool setup, love it. *SMILE*
hast Du mal zeit für ein treffen. ich würde gerne so einen converter bauen bräuchte aber noch ein wenig infos dazu, bin noch ein technik neuling.
hello How is he circuit to use control a PAP motor ??
Hi, I attempted to build the Arduino Uno version but can't get it to work properly - it triggers some notes but no better than just going directly from the RS output with a boosted signal - drops notes and doesn't play sequences in order. Also the activity LED doesn't light up. Are you positive the schematics are correct? It one comment here you mention needing 4 resistors, but only have 3 on the Arduino schematic. Any idea what might be going wrong? Thanks!
Hi, i am sorry if you have problems. My one works 100% thight, i never have drops till today. It's 2 years ago, i cant remember how exact i tested it for the Arduino uno, but i tested it and it worked. I can try to run it again and check if there are any problems with the translated arduino uno code. THE PROBLEM: I leve tomorrow for a 3 week vacation, if you can wait, we find a solution. but you need to be patient. sorry. Strange is that the led is not working when you have an output. Please check the wiring and the parts again for now. the code is so simple, input any signal = output 20ms 5V, thats it. Hope you can wait, thanx for your feedback.
Thanks for your reply! I'll be patient, if you could double check that would be great, thanks very much. I'll post here if I end up getting it working.
Just give it a try ... Remove all the wires from the board. Use a wire 5V on the arduino board to Aref on the other side, like in the schematics. Whitout that it won't work! Flash the arduino board again with the Xloader, set 115200 boud and use the right com port. After programming ( the LED shoud flicker in a high frequency. Now use a wire to connect the A0 and GND. each time you connect to GND, the Led i going to dark. Yes? Just to be shure your arduino is programmed ok, your board is working. If this works try again the rest. there can be more prblems, but i have no time yet to test again everithing.
Thanks, just tried this, the LED behaves exactly like you're saying - so I guess the problem is somewhere other than the Arduino..
These are the components I am using, are these right? I'm a novice with electronics: www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=57bbbecc58
easte of time
Hi A very good cutter I interested in made this cutter can you give me more data about your design and mechanism? thanks
need you mail address. thanx.
Hi Magicmastera! I'm wondering if you'd help to build my own kit, In fact I'd like one on both assignable out (A & B). A => would be the RIM B=> would the cowbell work? if yes Is there anything else to program in the Arduino Uno Board? I'm really newbie in programing and custom thing and I also definitely be interested to purchase this kit if you decide to make it.
This seems like a good solution, but I wish you'd go into more depth. I have an Arduino and understand how to flash it with the code but how do I go about connecting it to the TR-8 and SH-101? Is the rimshot being sent from one of the assignable outputs? What type of input is on the Arduino and also the output to the SH-101?
thanx. Just download the File from the description. You find a picture in the arduino Folder where you can see the wiring. Really easy to do. And wirks perfect since one year.
0947 664 974
I've created a laminar system but, it can't emit lights as bright as yours. Can you help?
Post a mail address, can send you some informations. KZread do kind a not allow anymore writing messages as it seems.
My email id is [email protected], I've already mailed you at your email.
Hi :) I'd also like to have some information about it! That would be very kind of you :) [email protected]
Could you please send me some instructions to build the system and any suggestions on color changer controller? [email protected]
i am aslo having trobule with light, can you send me your infor [email protected]
how do you stop water flow in mid way?
Hi magicmastera: any chance of a more in depth explanation on how to build this?
+ryanwellsmusic: Hi, all you need is to DL the Files, read carfully and look at the grafics. You Buy a arduino Uno board and follow the steps. thats the easyest way.
Please can you put a bass speaker near it and make the flow into a spiral? perhaps the volume of flow is impractiacl because it would need a very powerful sine wave to make it into a wobble laminar flow
Hey, doesn't tr-8 send all the midi notes from midi out?
+Ivan Stankov Hi, this has nothing to do with midi, its for syncing old analogue synth's with a 5V Trigger Pulse signal.
+magicmastera so it cant send sequence to other drum machines? I am going to try it with volca sample.
You can tell easily here how blue light reflects and refracts so much better. This is why the ocean and pools look blue. Too cool.
I found another solution. Increase the gain of the rim shot to say 150 or 200 and it produces enough to trigger the SH-101 correctly. The standard volume for each inst is set to 100. Look in the manual on how to do it.
+Botany 500 Wow, hoc clever! I nedd to test it. Thanx.
+Botany 500 Antother User mentioned that its not working. I tested it yesterday my self, your Idea is definitly not working! It drops so many beats, its not precise, forget it. For me, not a workaround. But thanx for your Input.
+magicmastera Yes, you are correct. I should have tried it properly. I just heard it was triggering more notes, and thought it was working. But, like you said it was not precise. I used a 707 with the 101 and the TR-8 sounds nothing like it. I have one question. I am going to make the sync box but I can not find the Attiny 45 (or 85) with 8MHZ. But, I found one with 10MHZ. Would that work too?
Hi, cool! You build your own! Yes the Atmel 45 or 85 works fine in any MHZ. But you need to programm this chip with my software, need an ISP programmer, you also need to change the mhz in the Fusebits. If you dont know how, it is easyer for you use a "arduino uno board" (about 20$), you can flash it by USB, use the XLoader xloader.russemotto.com/, i can try compile the software for you for the Arduino Uno, this should work fine. Yes, the Arduino Uno board is a bit too Big for this kind of Project, but if you dont have experience with microcontrollers, this is the most easyest way for you. let me know if you want to go this way.
+magicmastera Thanks for the response. If I buy the Arduino Uno board will I also need all the parts from the schematic?
dork
Hi, could you post some photos of what the box looks like inside? and the cable connecting to it? Thanks. I would like to try and make one.
Hi Peter, sorry i do not produce this parts, it's too much effort for single ones and would cost too much. About 6 - 7 Hours work. In the infos on top you find all the infos in the links to build one yourself. But thank you for your Interest.