Пікірлер

• 
  @MarkTruskolaski-bw4vfАй бұрын

  What it hard to take apart and put back together?

• 
  @frankstocker54752 ай бұрын

  Hello can you tell me what tyres you have on the scooter, I'm looking to replace mine. Thanks.

• 
  @TrevorChristie-gw4wn2 ай бұрын

  Hi there was wondering if you could help wondering what setting I should go to so I no if battery dieing

• 
  @blueberry60803 ай бұрын

  Hello, after you have loosened all the screws, use the hammer, but only minimally. then you simply pull off the right side (in the video). Do you have a hint for me? It doesn't work for me. I've already tried a few things, it just gets stuck and can't be loosened with one hand like you did.

• 
  @vetalm4 ай бұрын

  My Vsett 8 mudguard doesnt protect from flying mud and water to my back, do you have any ideas how to fix it?

• 
  @DarkFTP6 ай бұрын

  Hi! Thanks for videos. I am waiting for the delivery of my vsett10. Do you think it is possible to put a 150 mm airshock absorber in front?

• 
  @jekipon50466 ай бұрын

  What are the risks of a disk brake rotor installed in the opposite direction?

• 
  @user-ke9yk5qp3u8 ай бұрын

  I did this to my Mukuta 10 plus and it's way better. Went a tiny bit wider.

• 
  @JaybeezyOG_tv8 ай бұрын

  what size are your rotors?

• 
  @scottg4299 ай бұрын

  Do the p settings affect top speed at all?

• 
  @harrison00xXx2 ай бұрын

  The maximum power for sure. I need to set it to about 44-47% to get about 25-27 km/h top speed (as some sort of software speed limit) The issue by doing it this way... it loses nearly all its acceleration and torque for uphill, rendering the scooter useless.

• 
  @Ransomeware19 ай бұрын

  For those that don’t know about pressure for these air shocks, you’ll need to find your comfort spot in air. He is a 200lbs rider so you could use those settings for air pressure then dialing them back to find your ride comfort. I’m a lightweight rider about 140lbs and I have my settings set at 130 PSI main & 65 negative psi. To simplify this, MP (main pressure) should always be higher then NP (negative pressure) and it’s typically got to be about half of the main pressure (MP) . There is no perfect setting but depending on your weight you’ll need to start higher or lower to find your ride comfort.

• 
  @goofyahhh25410 ай бұрын

  update on the waterproofing ability of this method in your experience, since mine might be different - if you still use the scooter

• 
  @infinit28010 ай бұрын

  On vsett8 p15 at what should IT be kept

• 
  @GeeboysProductions11 ай бұрын

  You mentioned you raised your mud guard on the front. Do you have a video or can you explain how you did this? Thanks!

• 
  @freddierickfortades483511 ай бұрын

  Hi, what is the screw size for the mudguard

• 
  @Whereisgio11 ай бұрын

  I got a vsett display for my zero 9 what settings should I put to match my zero 9?

• 
  @almusic4276 Жыл бұрын

  Who the fook puts music when he talks in his video

• 
  @treysanders4509 Жыл бұрын

  Thanks. I read the manual but wasn’t understanding some of the stuff.

• 
  @mightycromm6299 Жыл бұрын

  Do you have a link to the titanium bolts please

• 
  @pripiselisabeta1973 Жыл бұрын

  Is there any phone app for the vsett 8 plus?thanks

• 
  @CoronaS-vdn Жыл бұрын

  I have 6 pcs Rockshox Monarch RL 165mm but if I put this and lower the pressure and adjust the reboun can I get a better result?! instead of a measly 125mm🙄

• 
  @CoronaS-vdn Жыл бұрын

  absurd to design such an expensive scooter with a ridiculous 125mm suspension !! I keep my blade with 165mm suspension

• 
  @CoronaS-vdn Жыл бұрын

  it possibile mount 165mm front?

• 
  @Mwellmac Жыл бұрын

  Question... if I add the larger rotor on the back wheel will changing the caliper mount result in the caliper touching the stock fender?

• 
  @carbot6801 Жыл бұрын

  What rise are the new bars how does the height compare to the originals ?

• 
  @N3xus_6 Жыл бұрын

  This looks like a Rotor upgrade not the actual brakes. Thought you might be upgrading the brakes to Shimano or Magura, that would be awesome.

• 
  @ObieJrBafour Жыл бұрын

  I really like your wording with this video with your testimony. I have 10" heel scooter as well i wanted to know if 180mm was pushing it? My tires are 80/65 u have any opinions

• 
  @hristocvetkov7903 Жыл бұрын

  Hello i whant to upgrade my electric scooter im with 160mm brake disk and i whant to replace it with 180mm but i need adaptor. My question is what adaptor i have to buy so i can put a 180mm brake disk. Can you tell me my scouter is Blade GT

• 
  @hristocvetkov7903 Жыл бұрын

  Ans what is your opinion for 180mm 😅

• 
  @machyne82 Жыл бұрын

  Good looking colors. I can’t stand the yellow. Yours looks sick

• 
  @dorofeya1474 Жыл бұрын

  Poor quality work. There is a headlight on the front fender and if it is THAT is how it is raised, then it will blind all oncoming pedestrians and drivers. Raise the front fender ON 4 WASHERS (one washer for each bolt). Only then the direction of the headlight will not change. And there is no point in raising the rear wing at all, on VSETT 10+ there are no problems with it.

• 
  @abundantharmony Жыл бұрын

  What kind of tire is that as well?

• 
  @rizuanchannel Жыл бұрын

  Nice

• 
  @geraldbailly5654 Жыл бұрын

  Bonjour quel est le diamètre des nouveaux disques s'il vous plaît ? merci .

• 
  @QbertTehKiller Жыл бұрын

  Those colors are so freshhh

• 
  @k9teamzagrebskolazapse149 Жыл бұрын

  That is first thing I did on Vsett 8 att rear bumper is litle noisy and after that it's silent.

• 
  @sebastianeyeless3835 Жыл бұрын

  Hi how are u? nice video....can u say me What damper did you install? the 125mm or the 150mm?

• 
  @adambarczi6305 Жыл бұрын

  Great video. Juts one question: Is there a version without the background music? I cannot really hear what you say from the music. Many thanks

• 
  @EscDogAlt Жыл бұрын

  Thanks. After seeing the other video I just decided to make inspecting them something I do every 800 km or so, and this video helped me look at the locking nuts too. Absolutely no problems at 800 km.

• 
  @Macca-jv9vp Жыл бұрын

  My air shock on the front just burst at 40mph, Scary

• 
  @byronw31122 ай бұрын

  did it cause a crash? What did you replace it with?

• 
  @julioenriquevargasdelahoz3530 Жыл бұрын

  No hay algún truco para más velocidad de la vsett 8?

• 
  @GidDree Жыл бұрын

  Please tell me where you guys get replacement bolts for the Vsett? I lost the split hub black bolts, anyone know the size of these things and where can I find replacement bolts..????HELPPPPP !

• 
  @GidDree Жыл бұрын

  Are the bar ends 22.2 or 22.0 mm? And the stem 31.? 32.? Help not sure what I need..EDIT any links to that bar please?

• 
  @martinritch5241 Жыл бұрын

  Of all the KZread channels that pertain to electric scooters, you have the very best looking scooter of all. Keep up the good work and keep it coming.😎🙏🇺🇸🇨🇦

• 
  @Peter-ch5hd Жыл бұрын

  Hi, I cannot find a link to the handlebar?

• 
  @papotaino1516 Жыл бұрын

  Just got my Vsett 10+ today big help thanks

• 
  @paulkrzystyniak8668 Жыл бұрын

  The yellow on the tires- did you do that witha paint pen?

• 
  @blazingcryptic4050 Жыл бұрын

  I got my vsett10+ and the front mudguard is touching the tire on one side and other side off the tire

• 
  @escootermodificationguides2149 Жыл бұрын

  Sounds to me one off the brackets may be bent?

• 
  @pauleemoran9178 Жыл бұрын

  So wot will I need 2x 180 brackets for 160 mm roters plz send link

• 
  @sambo7015 Жыл бұрын

  I can not unlock the on-board computer after nfc settings. What to do?

• 
  @oswaldpinzon5086 Жыл бұрын

  friend. Front suspension can be adjusted. A5 RR1 150mm?? BEST REGARDS

• 
  @geoffsharp2436 Жыл бұрын

  The 150mm version has too much travel and can only be used with low pressure.

• 
  @CoronaS-vdn Жыл бұрын

  @@geoffsharp2436I have 6 pcs Rockshox Monarch RL 165mm but if I put this and lower the pressure and adjust the reboun can I get a better result?! instead of a measly 125mm