I would never sell it. It is one of my favourite planes 😊
@Ultramesh4 күн бұрын
Hi there, a very nice build video, I've seen it a few times now. Do you know the Inside F5J model? If you do, how does this Triple Neo compare to the Inside F5J in terms of flight handeling?
@bavarian_rc4 күн бұрын
Thanks, great that you liked the video. I don't know the Inside F5J but I checked the specs. According to the data I found I would say that the Inside is lighter than the Triple Neo Thermic and has therefore a much lower wing loading (17g/dm2 vs my Triple Neo Thermic 27g/dm2). The Inside seems to be comparable with my F5K Maverick in terms of flight performance (with the Maverick being smaller of course). For calm days I usually use my Maverick and for slightly more windy days I use the Triple Neo which can handle the wind a bit better. The wing structure of the Inside seems to be also quite similar to my Maverick. The Triple Neo has a much stronger wing structure (allowing for more wind). That's about all I could say. I hope this helps.
@Ultramesh3 күн бұрын
@@bavarian_rcYes thanks. The solution of course is to get both, lol. I have the Inside on order this week already as there was a deal on it. What is the all up weight of this Triple Neo Thermic?
@bavarian_rc3 күн бұрын
@Ultramesh Good idea, get both 😜 My Triple Neo Thermic has an AUW of 1281g. The tail of mine got a bit too heavy, so I needed some weight in the nose to balance. You can easily save 100g if you build the tail a bit lighter.
@robysimo14 күн бұрын
La tua costruzione è davvero bella. Ho ordinato il contenitore per poter replicare la tua build, grazie per il tuo prezioso contributo
@bavarian_rc4 күн бұрын
Thanks, great that you liked it. I am using 2 of these Lipo safes since years now and I am still very happy with them. Enjoy the build! Ciao 🙌🏻
@user-tt6cb5wo4n5 күн бұрын
my plane foam glider is definitely not same like you before you make twin turbo lidl
@bavarian_rcКүн бұрын
Would like to see yours
@user-tt6cb5wo4n5 күн бұрын
my plane foam glider is definitely not same like you before you make twin turbo lidl
@bavarian_rc5 күн бұрын
😁
@loganpresley5366 күн бұрын
That motor does not seem to be available here in the US……just wondering if you have a suggestion for an alternate ?
@bavarian_rc6 күн бұрын
I only tested it with the original actro-N 28-4-880. I did a quick check in some German RC forums. Some alternatives that are mentioned there: D-Power AL 2835-9, Hacker A20-12 XL EVO kv1039, Turnigy 2210A 1650kv, AXI 2217-20. This might help you for further investigation. I haven’t got any experience with those. You might also want to check ecalc, which is an online tool for finding the right setup for your plane. It is very useful for finding the right motor/ prop combination. Totally worth the money for the full version.
@loganpresley5366 күн бұрын
Thanks, that helps!
@jeanlucvassort64116 күн бұрын
Master build, video edition etc ... Thanks
@bavarian_rc6 күн бұрын
Thanks, great that you liked it 😊
@ModifiedRC08779 күн бұрын
Sick! Would you make and sell me one?
@bavarian_rc8 күн бұрын
Happy that you like it. Unfortunately I can't build one for you. The effort (and cost) would be too high. Not sure about the exact time I needed to build one, but 15-20 hours seems realistic. So this is really for people who want to build themselves. There is the batsafe on the market which is similar and is around 80 EUR.
@r-k.fotografie207116 күн бұрын
Auch ich möchte erstmal das tolle Video loben obgleich ich nichts verrstehe weil alles in Englsich ist..schade.. Das Antriebssetup muß wohl echt schlecht sein wenn man ihr mit Gebläse arbeiten muß... Auch mir ist schon ein Actro Motor durchgebrannt im Helios ....
@bavarian_rc15 күн бұрын
Danke fürs Lob. Das mit der Englischen Sprache hilft mir halt, da ich auf eine internationale Zielgruppe abziele. Der actro Motor ist in diesem Setup am oberen Rand dessen was er aushält. Im normalen Einsatz ist das kein Problem, da nach einem Steigflug eine längere Segelphase kommt. Als ich die Szenen fürs Video gefilmt habe war das natürlich weit weg vom normalen Einsatz. Erstens hat die Kamera oben drauf den Widerstand stark erhöht, speziell die Insta360 One X ist ein ziemlicher Brocken, ganz zu schweigen vom zusätzlichen Gewicht. Somit war für den Steigflug viel mehr Motorlaufzeit nötig. Zweitens war natürlich auch die Segelflugphase durch das erhöhte Gewicht und den großen Widerstand viel kürzer. Also mehr Motorlaufzeit und weniger Abkühlphase. Somit blieb mir nur das Kühlen zwischendurch mit dem Gebläse. Im normalen Einsatz hatte ich bisher keine Temperaturprobleme, ich hab den Triple Neo Thermic aber noch nicht im Hochsommer eingesetzt.
@Rantanplan-081518 күн бұрын
How you do this with the tape on the bottom site of the wing?
@bavarian_rc18 күн бұрын
Not sure to catch what you mean. Can you give me the position (time) in the video. I will be happy to answer your question. You can also write in German if you prefer.
@Rantanplan-081518 күн бұрын
Hi, Thanks for the answer👍. Yes,i must say it direkt what i mean. In german is much easyer for me😅: Ich meine minute 48:43(video). Du klebst das untere klebeband,ohne das ruder ganz um zu klappen. Wie bekommst du das klebeband in den spalt,sodass sich beide seiten berühren? (Ich habe gerade die selbe Prozedur beim flixx😅) Normalerweise lassen sich die ruder ja ganz auf die oberseite umklappen,sodass eine gerade fläche entsteht,wie bei deinen querrudern,dann kann man das band einfach aufkleben. Aber das tesa in einen spalt reindrücken bekomme ich nicht "sauber" hin😅
@bavarian_rc18 күн бұрын
Hi, jetzt ist alles klar 👍. Also schon mal vorne weg, das Anscharnieren mit Tesa ist und bleibt eine meiner weniger beliebten Aktivitäten um es mal vorsichtig auszudrücken. 😂 So wie ich das beim Triple Neo Speed gemacht habe, mache ich es heute nicht mehr. Inzwischen mache ich das so, wie es in der FMT Heft 09/2018 beschrieben ist. Wenn Du das Heft nicht hast, dann schicke mir einfach eine Mail and meine Email-Adresse (siehe Kanal-Info / Impressum). Dann kann ich Dir die Info schicken. Eine leicht abgewandelte Version dieser Methode ist in meinem Bauvideo von den Triple Neo Thermic Flächen (kzread.info/dash/bejne/nqupm62YipzWftI.html) zu sehen (1:01:45). Allerdings habe ich dort die 30mm Streifen alle mit der gleichen Orientierung angebracht, also von Oberseite Tragfläche auf Unterseite Querruder. Hier wäre es besser gewesen abwechselnd auch einen Streifen von Unterseite Tragfläche auf Oberseite Querruder anzubringen. Bei meinem letzten Bauvideo vom Maverick (kzread.info/dash/bejne/Z5ebq65ypLvVqbA.html) sieht man das richtig (1:05:41). Beim Höhenruder bzw. Seitenruder lässt sich diese Methode in gleicher Weise anwenden. Mit etwas Übung funktioniert das recht gut. Ach ja, beim Anbringen des langen durchgehenden Tesastreifen am besten das Ruder leicht auslenken, sonst geht das Ruder später etwas schwer, da der Tesa "spannt". Das sieht man beim Maverick Video bei 1:06:43. Ich hoffe das hilft Dir weiter. Schönen Sonntag noch. Ich werde mich jetzt auch in den Bastelkeller begeben, was soll man sonst bei dem Wetter auch machen... Grüße, Robert
@jorgecastorena576220 күн бұрын
That is a clean build. I feel like I'm a little kid compared to this man.
@bavarian_rc19 күн бұрын
Thanks a lot. I do my best to have clean builds. But I am sure you are too humble. And in the end the main thing is that it flies straight and we're having fun 😀😉
@leeliddle702121 күн бұрын
Spends more on a GPS unit than the airplane.
@bavarian_rc20 күн бұрын
You don’t know how much time I spend on my airplanes 🤣
@GiovanniBausC21 күн бұрын
Großartig gemachtes Video! Wie ist das Flugverhalten insbesondere in der Thermik im Vergleich zum Helios? Bindan Propellerleim finde ich übrigens noch besser als Ponal.
@bavarian_rc20 күн бұрын
Danke! Zum Helios kann ich leider nichts sagen da ich keine praktische Erfahrung mit ihm habe. Generell geht der Triple Neo Thermic schon ziemlich gut in der Thermik. Von der Größe und Gewicht spielen beide in der gleichen Klasse weshalb ich sehr ähnliche Performance erwarten würde. Danke für den Tipp mit dem Propeller Leim. Werde ich ausprobieren.
@mblaber200022 күн бұрын
IKEA should sell this…
@bavarian_rc22 күн бұрын
😂 yes! 👍🏻
@cyberyoda161123 күн бұрын
Really? You made THIS and you used 20.000 bucks technology? Are you serious? Only if you can't find anything similar on the market, or it is too expensive, that is OK. And you used A LOT of things, even a 3D printer, to make 2 pieces of clamps? Really? You can buy for 34$ the third hand with 3 hands, with a solder stand, with the paste/sponge/wire stands. With the magnifying glass. And the Chinese thing you threw in the garbage, it is very practical and cheap, it is your problem that you loosen all screws and you are surprised that it is like a limp dick. You can add some rubber washers, you can get any pressure you want, and even a pit bull couldn't take your wires from you. But, you choose to be smart. To make 10$ thing with machines of 20.000 bucks. Congratulations.
@bavarian_rc23 күн бұрын
Have you ever tried one of these cheap Chinese ones? If it is not that the arms let go then it slips across the table because the base is too light. It is and remains crap. So why did I do it myself? Simply because I can 🤣 If you can’t make it yourself then go on buying that crap with the beautiful magnifying glasses 😜
@cyberyoda161122 күн бұрын
@@bavarian_rc I have this cheap third-hand right now on my table. I don't see that the base is too light. You are going to solder, not to fight bulls. If you need more weight, the base is made of iron, so you can put some big magnets which we all used to take from the broken speakers when we were kids (or you extracted them to magnetize your screwdrivers). I can make it to weight for 1kg if I want. I am sure there are some other methods, to drill the hole through the base and to screw it on the piece of the wooden plank. If we need this to put two wires together, we generally need only 1 clamp, the other wire we can hold in hand. But, for less than 4 bucks, these Chinese clams are perfect. Of course, you can use 100.000$ tools, and 400$ of materials, to make a wooden toothpick, BECAUSE YOU CAN. This is exactly what you do. You used 3D PRINTER (???!!) to make a stand for your hand???? Hi-tech to make a wooden spoon? You just need a good knife and a piece of wood. A good branch. You spent more than the best hands costs on the market. The purpose of everything is to make something cheaper, to make something which you can't buy in your country, to make something which can't be bought anymore. Or to make it because you have some special demands, and you want to meet them. For instance, there is the best third hand ever: www.amazon.com/Helping-Soldering-Station-Auxiliary-Welding/dp/B0BQZ25ZT4/ref=sr_1_117?crid=36C0WKRYMDQ98&dib=eyJ2IjoiMSJ9.Ez51J3FKojgKA8ln_lI36ygS4x7D76OFJ8OQgWF7aS-YiGXgW72tdaiRQmKeOoaO0BfaxUdZfyTYmbmQhdDDZj6NdflXsOR4OiJrhOoWcxPturlyUIswCT_Nsk4jFRxDjbnuUWY7VAlG7gJ_NrHgUXYc5X2aF61D3RkBl_9rSyDShuOz-8IPeV1Le0n3W-vwQ34wTA_VqFhzMYafMnGofnh11Uac6F33A4Y9Rk-bpUmDJKJw1WxIHZSdCuedSv3OoaPeaR-ppOnlQZFoSBY5l7ffIOaZ3-IcWOuMlR1vomo.mHFMQFli_hNJpV94Fprm5QXkDPY-wRdjozPyDGsZTso&dib_tag=se&keywords=helping+hands+soldering&qid=1713272813&sprefix=helping+hands%2Caps%2C198&sr=8-117 The shape is great, the hands are not just cheap clumps, they are pretty solid, they can be folded, and you get the working surface, this is the great thing. It is cheaper than your work.
@mblaber200025 күн бұрын
Sanding to remove the chunks of flesh…
@bavarian_rc25 күн бұрын
Kind of 😜
@andreyl270528 күн бұрын
awesome)
@bavarian_rc28 күн бұрын
Thanks a lot 😀
@petertrigiani3129Ай бұрын
Ciao Roberto, I have used a 5-minute epoxy resin /hardener combination. I believe that I do not work fast enough in order to properly coat all parts / roving material and then attach the elements concerned. In the video....is the ratio of 10g resin : 4g hardener applied throughout the build? ( I saw that ratio on the build of the Neo-Speed....simply wondering if the same ratio was applied here in the Neo Thermic Time Lapse video. Am I better to use a 24-hour epoxy mixture? Opinion? Spring has sprung here....finallya day above 10 degrees C. Peter
@bavarian_rcАй бұрын
Hi Peter, 5-minute epoxy will not really work. It takes around 20 minutes to properly apply the roving, the thickened epoxy on the ribs and the glass fiber. No chance with 5-minute epoxy. I definitely recommend using normal 24-hour laminating epoxy (not casting epoxy). The one I use has 40 minutes pot life, which lets you do all the work without any stress. The mixing ratio depends on your resin system. Usually 5-minute epoxy is 50:50 (in volume). My laminating epoxy system is 100:40 (in weight). With epoxy you need to strictly follow the ratio given by the manufacturer. More hardener to have quicker reaction will not work. In that case the excess hardener would not react and you would get a bad result (might stay sticky). This is different to polyester resin where the amount of hardener can be varied. I never us polyester resin for RC builds. I hope this helps and don't hesitate to come back with any questions you might have. Happy to answer them all! Ciao Robert
@nickgeomapАй бұрын
How did you make those panning shots from close range just above the glider in flight?
@bavarian_rcАй бұрын
With a 360 Camera. I am using the Insta360 One X mounted on top of the fuselage
@brunokempter5186Ай бұрын
Wie ist Bausatz bestellbar? Wo? Euro? FR.???
@bavarian_rcАй бұрын
Bei FlightPoint: flightpoint.co/product/maverick-f5k-electric-glider/ Kostet 197$
@petertrigiani3129Ай бұрын
Good day to you and hoping that winter has come to a fine end for the season! At time stamp 37:05 are you using the fibreglass reinforcement with the epoxy mixture or with the fibreglass repair resin? I just want to be clear although it looks like you are using the standard epoxy mixture with micro balloons added. Please confirm when you can.....and thank you once again for such an eloquent time lapse video! Ciao e a presto!!!
@bavarian_rcАй бұрын
Hi Peter, indeed winter has come to an end. We already had the first beautiful days with above 20°C and the next weekend promises unbelievable 28°C. As usual we are boosted from 10°C to 28°C within only few days. You are right, I am using the same epoxy resin for all. I mix a portion of resin and then put half of it into a 2nd pot, where I add micro balloons and thixotropic powder. For the carbon roving at the trailing edge I am using the standard resin without any additive. On the ribs along the trailing edge I am using the epoxy with the micro balloons. For the fibreglass at the wing root I am again using the standard epoxy. For the ribs again the resin with the micro balloons. Keep me updated on your build! Ciao Robert
@Helicopterpilot16Ай бұрын
I wish I could find one of these kits!
@bavarian_rcАй бұрын
Hi, you might check out Aloft Hobbies. They have the fuselage and the speed wing available as separate kits. alofthobbies.com/products/aeronaut-triple-neo-fuselage-kit alofthobbies.com/products/wing-kit-for-aero-naut-triple-speed-model?variant=40019442499721 The thermic wing is only available as in the kit with the (old) balsa fuselage alofthobbies.com/collections/thermal/products/aero-naut-triple-thermic-2-5m-electric-glider
@RudibeataАй бұрын
Immer eine Freude dir zuzuschauen. 1. Sahne. Grüße Rudi
@bavarian_rcАй бұрын
Vielen Dank, das freut mich sehr 😄 schöne Grüße Robert
@eliaseseniorji2413Ай бұрын
I don't like this video because you are destroying the plane that you just bought I don't know why you 😭😭 spoilt the plan
@bavarian_rcАй бұрын
Destroying things is something I am quite good in 🤣
@CorgiAldoАй бұрын
Nice Build!
@bavarian_rcАй бұрын
Thanks 😊
@gordonyork6638Ай бұрын
god this is horrid music, what AI came up with that?
@bavarian_rcАй бұрын
Well that‘s the best that KZread is offering to us poor little content creators that can‘t afford expensive audio licenses 😂
@benoitkina9551Ай бұрын
Nice build ... to fix the plan on the table I use transparent adhesive film: easier, in 1 operation you protect the plan and it’s fixed on the table
@bavarian_rcАй бұрын
Thanks 😊 Good idea to use transparent adhesive film. It isn‘t one of my favorite tasks to fix the film on the plan and have it properly tensioned. Do you have a link to the one you use?
@jitendrajadhav9212Ай бұрын
Dear sir, thanks for sharing such a beautiful video explaining with practical , I am Jitendra Jadhav from I India, Pune , hobby flyer and I do also aeromodelling,
@bavarian_rcАй бұрын
Thanks a lot for your feedback. I am happy that you liked my video and found it helpful. Many greetings to India
@tobiasschilcher2778Ай бұрын
Top Video, hab mir das Video jetzt schon zum 4x angeschaut und werden mir jetzt noch den Flieger holen. Welchen Kleber gibst du bei Minute 28:00 auf die Fläche für das Fieberglas? Muss ich mir auch noch holen. Danke
@bavarian_rcАй бұрын
Vielen Dank! Den Triple Neo kann ich wirklich nur empfehlen, ich fliege ihn immer wieder gerne, sowohl mit den Speed Flächen als auch Thermic Flächen. Der Kleber ist Epoxid Laminierharz. Ich verwende das Epoxidharz L mit Härter L von R&G (www.r-g.de/art/100110)
@TheFreakyman81Ай бұрын
Sehr schönes Video! Wie lange lässt man den Leim ungefähr trocknen bevor man zum nächsten Schritt kann?
@bavarian_rcАй бұрын
Danke! ☺️ Es kommt darauf an, welchen Leim man nimmt und wie kritisch eine Verklebung ist. Ich benutze Ponal Express, der trocknet relativ schnell. Unkritische Stellen lasse ich ca. 1 Stunde trocknen, kritische Stellen wie z.B. Holm oder die Beplankung lasse ich schon mehrere Stunden oder besser über Nacht trocknen. Wenn man zu früh weiter macht kann sich leichter was verziehen.
@valeglidersАй бұрын
Thanks for sharing, enjoyed watching this and it has nudged me a bit closer to making a purchase, think it would make a perfect plane to take for a walk and do some hedge hopping. 👍
@bavarian_rcАй бұрын
Thanks, happy that you liked it and that I could inspire you to possible build the Maverick as well. I still haven't maidened it, but I will for sure do a flight video, so keep an eye on my channel 😀
@petertrigiani3129Ай бұрын
On my balsa build of the Triple Neo Thermic....I have experienced warping of the wings structure. I am using standard carpenter glue and appropriate weight to hold down the layers as the glue dries. is there a remedy for this warpage?
@bavarian_rcАй бұрын
Hi Peter, on the Triple Neo Thermic I had no issues with warping. In which area is it? There is some chance of recovering the warping during the covering with film by shrinking the film differently strong in order to counteract the warping. Nevertheless you should not expect too much from that. If the warping is really bad you might have to consider removing the part that caused the warping and redo it. Was it caused by the sheeting or was it present before? Were the sheets already warped before glueing? in that case even after using weights and waiting for the glue to fully cure the forces in the sheeting will try to get back to the initial shape which could result in warping. Balsa is normally not so critical but plywood has more power.
@petertrigiani3129Ай бұрын
Yet another fine build!!! Bravo!!!
@bavarian_rcАй бұрын
Thanks a lot. It was a really nice build experience. I still haven't had the chance to maiden it, but I will do that soon.
@XFBO2 ай бұрын
Fantastic build!! Thank you for sharing! I bought one of these a few months ago but haven't begun building just yet, glad I didn't now that I have this vid to reference!
@bavarian_rc2 ай бұрын
Thanks, great that you liked it! Have fun with the build! I enjoyed it a lot.
@ralphcramden29362 ай бұрын
One of the best fpv videos I've seen. Keep watching over n over
@bavarian_rc2 ай бұрын
Thanks a lot 😀
@alessiofusiio47202 ай бұрын
beatiful build, unlike the one on my triple neo. also, my wings aren't attacched very well to the fousolage and they flex pretty much by the point they join to the fusolage. any tips to solve it?
@bavarian_rc2 ай бұрын
Thanks! I also have some flex in the wings but in the area of the fuselage-to-wing joint they should be quite strong. Without further details it is hard to say how to fix. You could send me some pictures to show exactly where the flex is and in which direction it flexes. You can find my mail address in the channel info.
@papayankee52682 ай бұрын
Great vid, with really helpful tips. Many thanks !
@bavarian_rc2 ай бұрын
Thanks a lot. I am happy that some of my tips are useful. I keep learning with every build and I enjoy sharing it with the community
@MalcolmCrabbe2 ай бұрын
Its been 50 years since I last built an RC plane. Wish the kits back then were like this. The colour coded sections make it very clear. I have no inclination to get back into the hobby, but this video was very enjoyable to watch and would provide an excellent aid to anyone building the same kit.
@bavarian_rc2 ай бұрын
Thanks a lot! I built my first kit mid of the 80's, a Graupner Amigo II. Indeed a significant difference to our laser cut kit nowadays. I have learned everything back then from my father and these skills still come in handy even with high precision part in todays kits
@XFBO2 ай бұрын
The laser printers have improved this hobby immensely!!!
@bavarian_rcАй бұрын
Absolutely! 👍
@tobiasschilcher27782 ай бұрын
Great Job, now i need to buy this kit also.
@bavarian_rc2 ай бұрын
Thanks. I guess you really gotta get one 😜
@bigsmokerc2 ай бұрын
Fantastic video. The first (and only) model I ever built like this was very satisfying, but I certainly made a few mistakes. Would you classify this as an appropriate second model to build? It's exactly the size and type I would enjoy flying.
@bavarian_rc2 ай бұрын
Thanks, great that you liked it! There are some key elements for this build, like getting the fuse straight and not warping the control surfaces during covering with film. They require a bit of experience. I would rather say the Maverick is a 3rd than a 2nd model to build. But if you take my video as a guide and go carefully step by step, why not?
@meljones70662 ай бұрын
I built this model last year, I am still trying to learn how to fly it correctly, I tend to fly it too slowly and find that I keep inducing a stall, when this happens near to the ground damage is caused, so I have had to make some repairs.
@bavarian_rc2 ай бұрын
I am curious to see how it will fly. I will remember your comment for the first flights and be careful. Have you tried changing the CG and maybe also the angle of attack of the horizontal stabilizer? Both are connected and have a strong influence on the flight characteristics. If the thin fuselage is not perfectly straight your hstab could be a little bit off.
@meljones70662 ай бұрын
Good tip, I will check it out. Many thanks.@@bavarian_rc
@mikekelly67742 ай бұрын
Another great build video. I'm curious what the total build time is from unboxing to ready-to-fly.
@bavarian_rc2 ай бұрын
Thanks, I am happy that you liked it. Hard to tell what the total build time was. It took me 3,5 months with some periods of more and some with less progress.
@mikekelly67742 ай бұрын
@@bavarian_rc Thank you for answering. Truely a labor of love.
@bavarian_rc2 ай бұрын
Oh yeah, it‘s all about building 😄
@catfish8282 ай бұрын
Top !
@bavarian_rc2 ай бұрын
Thanks 😊
@Rudibeata2 ай бұрын
War mir wieder eine große Freude Dir zuzuschauen. Grüße Rudi.
@bavarian_rc2 ай бұрын
Danke, schön dass es Dir gefallen hat! Schöne Grüße Robert
@sebaldmodellbau6382 ай бұрын
Tolles Video, da steckt sehr viel Arbeit dahinter. Wenn ich mich nicht täusche, dann müsste der Fluss die Wörnitz sein.
@bavarian_rc2 ай бұрын
Danke ☺️ Richtig erkannt, das ist die Wörnitz.
@jimsodowsky12982 ай бұрын
Your build video really paid off with your flying the Shaka.. I really enjoyed living in your Country years ago.
@bavarian_rc2 ай бұрын
Thanks! Great that you liked it ... I mean the Shaka and our country 👍😀
@Jinntsai2 ай бұрын
Performance art for relaxing!
@bavarian_rc2 ай бұрын
😊 Great that you liked it!
@Jetseb892 ай бұрын
I'm impressed by the quality of the transformation work - well done. I'm going to have to find one before the sun comes out ;)
@bavarian_rc2 ай бұрын
Thanks a lot! Go get one for yourself, it’s really a simple and quick build and so much fun to fly. Did you also see my flight video?
@Jetseb892 ай бұрын
@@bavarian_rc Yes, I watched it and it finally made me want to get on with the project :=)
@bavarian_rc2 ай бұрын
😁👍🏻
@charliemarkovic43012 ай бұрын
The sound track reminds me of Tron.
@bavarian_rc2 ай бұрын
😂👍🏻
@tobiasschilcher27782 ай бұрын
Servus, mal wieder ein geiles Video. Hast du mal vorn den neuen Flixx von aeronaut zu bauen? Lg Tobias
@bavarian_rc2 ай бұрын
Danke, schön dass es Dir gefällt. Den Flixx hab ich nicht auf meiner Liste. Die ist auch schon ziemlich lang 🤣 Als nächstes kommt der Maverick von Flightpoint (ist schon fast fertig) und danach hab ich schon mehrere weitere Bausätze zuhause. Sieht also eher schlecht aus für den Flixx, ist aber schöner Flieger 👍🏻 würde mir auch gefallen. Schöne Grüße Robert
@tobiasschilcher27782 ай бұрын
Moin Robert, schade. Aber freue mich schon über deine neuen Videos. Ich liebe es die Videos zu schauen und selbst nebenbei zu bauen. Danke für deinen Content und deinen fleiß die Videos zu machen.
@bavarian_rc2 ай бұрын
Vielen Dank, das ist ein tolles Feedback! Wenn ich mal keinen Bock auf selber bauen hab, dann schau ich auch gerne anderen beim Bauen zu 😃
Пікірлер
Can i buy? 🥺
I would never sell it. It is one of my favourite planes 😊
Hi there, a very nice build video, I've seen it a few times now. Do you know the Inside F5J model? If you do, how does this Triple Neo compare to the Inside F5J in terms of flight handeling?
Thanks, great that you liked the video. I don't know the Inside F5J but I checked the specs. According to the data I found I would say that the Inside is lighter than the Triple Neo Thermic and has therefore a much lower wing loading (17g/dm2 vs my Triple Neo Thermic 27g/dm2). The Inside seems to be comparable with my F5K Maverick in terms of flight performance (with the Maverick being smaller of course). For calm days I usually use my Maverick and for slightly more windy days I use the Triple Neo which can handle the wind a bit better. The wing structure of the Inside seems to be also quite similar to my Maverick. The Triple Neo has a much stronger wing structure (allowing for more wind). That's about all I could say. I hope this helps.
@@bavarian_rcYes thanks. The solution of course is to get both, lol. I have the Inside on order this week already as there was a deal on it. What is the all up weight of this Triple Neo Thermic?
@Ultramesh Good idea, get both 😜 My Triple Neo Thermic has an AUW of 1281g. The tail of mine got a bit too heavy, so I needed some weight in the nose to balance. You can easily save 100g if you build the tail a bit lighter.
La tua costruzione è davvero bella. Ho ordinato il contenitore per poter replicare la tua build, grazie per il tuo prezioso contributo
Thanks, great that you liked it. I am using 2 of these Lipo safes since years now and I am still very happy with them. Enjoy the build! Ciao 🙌🏻
my plane foam glider is definitely not same like you before you make twin turbo lidl
Would like to see yours
my plane foam glider is definitely not same like you before you make twin turbo lidl
😁
That motor does not seem to be available here in the US……just wondering if you have a suggestion for an alternate ?
I only tested it with the original actro-N 28-4-880. I did a quick check in some German RC forums. Some alternatives that are mentioned there: D-Power AL 2835-9, Hacker A20-12 XL EVO kv1039, Turnigy 2210A 1650kv, AXI 2217-20. This might help you for further investigation. I haven’t got any experience with those. You might also want to check ecalc, which is an online tool for finding the right setup for your plane. It is very useful for finding the right motor/ prop combination. Totally worth the money for the full version.
Thanks, that helps!
Master build, video edition etc ... Thanks
Thanks, great that you liked it 😊
Sick! Would you make and sell me one?
Happy that you like it. Unfortunately I can't build one for you. The effort (and cost) would be too high. Not sure about the exact time I needed to build one, but 15-20 hours seems realistic. So this is really for people who want to build themselves. There is the batsafe on the market which is similar and is around 80 EUR.
Auch ich möchte erstmal das tolle Video loben obgleich ich nichts verrstehe weil alles in Englsich ist..schade.. Das Antriebssetup muß wohl echt schlecht sein wenn man ihr mit Gebläse arbeiten muß... Auch mir ist schon ein Actro Motor durchgebrannt im Helios ....
Danke fürs Lob. Das mit der Englischen Sprache hilft mir halt, da ich auf eine internationale Zielgruppe abziele. Der actro Motor ist in diesem Setup am oberen Rand dessen was er aushält. Im normalen Einsatz ist das kein Problem, da nach einem Steigflug eine längere Segelphase kommt. Als ich die Szenen fürs Video gefilmt habe war das natürlich weit weg vom normalen Einsatz. Erstens hat die Kamera oben drauf den Widerstand stark erhöht, speziell die Insta360 One X ist ein ziemlicher Brocken, ganz zu schweigen vom zusätzlichen Gewicht. Somit war für den Steigflug viel mehr Motorlaufzeit nötig. Zweitens war natürlich auch die Segelflugphase durch das erhöhte Gewicht und den großen Widerstand viel kürzer. Also mehr Motorlaufzeit und weniger Abkühlphase. Somit blieb mir nur das Kühlen zwischendurch mit dem Gebläse. Im normalen Einsatz hatte ich bisher keine Temperaturprobleme, ich hab den Triple Neo Thermic aber noch nicht im Hochsommer eingesetzt.
How you do this with the tape on the bottom site of the wing?
Not sure to catch what you mean. Can you give me the position (time) in the video. I will be happy to answer your question. You can also write in German if you prefer.
Hi, Thanks for the answer👍. Yes,i must say it direkt what i mean. In german is much easyer for me😅: Ich meine minute 48:43(video). Du klebst das untere klebeband,ohne das ruder ganz um zu klappen. Wie bekommst du das klebeband in den spalt,sodass sich beide seiten berühren? (Ich habe gerade die selbe Prozedur beim flixx😅) Normalerweise lassen sich die ruder ja ganz auf die oberseite umklappen,sodass eine gerade fläche entsteht,wie bei deinen querrudern,dann kann man das band einfach aufkleben. Aber das tesa in einen spalt reindrücken bekomme ich nicht "sauber" hin😅
Hi, jetzt ist alles klar 👍. Also schon mal vorne weg, das Anscharnieren mit Tesa ist und bleibt eine meiner weniger beliebten Aktivitäten um es mal vorsichtig auszudrücken. 😂 So wie ich das beim Triple Neo Speed gemacht habe, mache ich es heute nicht mehr. Inzwischen mache ich das so, wie es in der FMT Heft 09/2018 beschrieben ist. Wenn Du das Heft nicht hast, dann schicke mir einfach eine Mail and meine Email-Adresse (siehe Kanal-Info / Impressum). Dann kann ich Dir die Info schicken. Eine leicht abgewandelte Version dieser Methode ist in meinem Bauvideo von den Triple Neo Thermic Flächen (kzread.info/dash/bejne/nqupm62YipzWftI.html) zu sehen (1:01:45). Allerdings habe ich dort die 30mm Streifen alle mit der gleichen Orientierung angebracht, also von Oberseite Tragfläche auf Unterseite Querruder. Hier wäre es besser gewesen abwechselnd auch einen Streifen von Unterseite Tragfläche auf Oberseite Querruder anzubringen. Bei meinem letzten Bauvideo vom Maverick (kzread.info/dash/bejne/Z5ebq65ypLvVqbA.html) sieht man das richtig (1:05:41). Beim Höhenruder bzw. Seitenruder lässt sich diese Methode in gleicher Weise anwenden. Mit etwas Übung funktioniert das recht gut. Ach ja, beim Anbringen des langen durchgehenden Tesastreifen am besten das Ruder leicht auslenken, sonst geht das Ruder später etwas schwer, da der Tesa "spannt". Das sieht man beim Maverick Video bei 1:06:43. Ich hoffe das hilft Dir weiter. Schönen Sonntag noch. Ich werde mich jetzt auch in den Bastelkeller begeben, was soll man sonst bei dem Wetter auch machen... Grüße, Robert
That is a clean build. I feel like I'm a little kid compared to this man.
Thanks a lot. I do my best to have clean builds. But I am sure you are too humble. And in the end the main thing is that it flies straight and we're having fun 😀😉
Spends more on a GPS unit than the airplane.
You don’t know how much time I spend on my airplanes 🤣
Großartig gemachtes Video! Wie ist das Flugverhalten insbesondere in der Thermik im Vergleich zum Helios? Bindan Propellerleim finde ich übrigens noch besser als Ponal.
Danke! Zum Helios kann ich leider nichts sagen da ich keine praktische Erfahrung mit ihm habe. Generell geht der Triple Neo Thermic schon ziemlich gut in der Thermik. Von der Größe und Gewicht spielen beide in der gleichen Klasse weshalb ich sehr ähnliche Performance erwarten würde. Danke für den Tipp mit dem Propeller Leim. Werde ich ausprobieren.
IKEA should sell this…
😂 yes! 👍🏻
Really? You made THIS and you used 20.000 bucks technology? Are you serious? Only if you can't find anything similar on the market, or it is too expensive, that is OK. And you used A LOT of things, even a 3D printer, to make 2 pieces of clamps? Really? You can buy for 34$ the third hand with 3 hands, with a solder stand, with the paste/sponge/wire stands. With the magnifying glass. And the Chinese thing you threw in the garbage, it is very practical and cheap, it is your problem that you loosen all screws and you are surprised that it is like a limp dick. You can add some rubber washers, you can get any pressure you want, and even a pit bull couldn't take your wires from you. But, you choose to be smart. To make 10$ thing with machines of 20.000 bucks. Congratulations.
Have you ever tried one of these cheap Chinese ones? If it is not that the arms let go then it slips across the table because the base is too light. It is and remains crap. So why did I do it myself? Simply because I can 🤣 If you can’t make it yourself then go on buying that crap with the beautiful magnifying glasses 😜
@@bavarian_rc I have this cheap third-hand right now on my table. I don't see that the base is too light. You are going to solder, not to fight bulls. If you need more weight, the base is made of iron, so you can put some big magnets which we all used to take from the broken speakers when we were kids (or you extracted them to magnetize your screwdrivers). I can make it to weight for 1kg if I want. I am sure there are some other methods, to drill the hole through the base and to screw it on the piece of the wooden plank. If we need this to put two wires together, we generally need only 1 clamp, the other wire we can hold in hand. But, for less than 4 bucks, these Chinese clams are perfect. Of course, you can use 100.000$ tools, and 400$ of materials, to make a wooden toothpick, BECAUSE YOU CAN. This is exactly what you do. You used 3D PRINTER (???!!) to make a stand for your hand???? Hi-tech to make a wooden spoon? You just need a good knife and a piece of wood. A good branch. You spent more than the best hands costs on the market. The purpose of everything is to make something cheaper, to make something which you can't buy in your country, to make something which can't be bought anymore. Or to make it because you have some special demands, and you want to meet them. For instance, there is the best third hand ever: www.amazon.com/Helping-Soldering-Station-Auxiliary-Welding/dp/B0BQZ25ZT4/ref=sr_1_117?crid=36C0WKRYMDQ98&dib=eyJ2IjoiMSJ9.Ez51J3FKojgKA8ln_lI36ygS4x7D76OFJ8OQgWF7aS-YiGXgW72tdaiRQmKeOoaO0BfaxUdZfyTYmbmQhdDDZj6NdflXsOR4OiJrhOoWcxPturlyUIswCT_Nsk4jFRxDjbnuUWY7VAlG7gJ_NrHgUXYc5X2aF61D3RkBl_9rSyDShuOz-8IPeV1Le0n3W-vwQ34wTA_VqFhzMYafMnGofnh11Uac6F33A4Y9Rk-bpUmDJKJw1WxIHZSdCuedSv3OoaPeaR-ppOnlQZFoSBY5l7ffIOaZ3-IcWOuMlR1vomo.mHFMQFli_hNJpV94Fprm5QXkDPY-wRdjozPyDGsZTso&dib_tag=se&keywords=helping+hands+soldering&qid=1713272813&sprefix=helping+hands%2Caps%2C198&sr=8-117 The shape is great, the hands are not just cheap clumps, they are pretty solid, they can be folded, and you get the working surface, this is the great thing. It is cheaper than your work.
Sanding to remove the chunks of flesh…
Kind of 😜
awesome)
Thanks a lot 😀
Ciao Roberto, I have used a 5-minute epoxy resin /hardener combination. I believe that I do not work fast enough in order to properly coat all parts / roving material and then attach the elements concerned. In the video....is the ratio of 10g resin : 4g hardener applied throughout the build? ( I saw that ratio on the build of the Neo-Speed....simply wondering if the same ratio was applied here in the Neo Thermic Time Lapse video. Am I better to use a 24-hour epoxy mixture? Opinion? Spring has sprung here....finallya day above 10 degrees C. Peter
Hi Peter, 5-minute epoxy will not really work. It takes around 20 minutes to properly apply the roving, the thickened epoxy on the ribs and the glass fiber. No chance with 5-minute epoxy. I definitely recommend using normal 24-hour laminating epoxy (not casting epoxy). The one I use has 40 minutes pot life, which lets you do all the work without any stress. The mixing ratio depends on your resin system. Usually 5-minute epoxy is 50:50 (in volume). My laminating epoxy system is 100:40 (in weight). With epoxy you need to strictly follow the ratio given by the manufacturer. More hardener to have quicker reaction will not work. In that case the excess hardener would not react and you would get a bad result (might stay sticky). This is different to polyester resin where the amount of hardener can be varied. I never us polyester resin for RC builds. I hope this helps and don't hesitate to come back with any questions you might have. Happy to answer them all! Ciao Robert
How did you make those panning shots from close range just above the glider in flight?
With a 360 Camera. I am using the Insta360 One X mounted on top of the fuselage
Wie ist Bausatz bestellbar? Wo? Euro? FR.???
Bei FlightPoint: flightpoint.co/product/maverick-f5k-electric-glider/ Kostet 197$
Good day to you and hoping that winter has come to a fine end for the season! At time stamp 37:05 are you using the fibreglass reinforcement with the epoxy mixture or with the fibreglass repair resin? I just want to be clear although it looks like you are using the standard epoxy mixture with micro balloons added. Please confirm when you can.....and thank you once again for such an eloquent time lapse video! Ciao e a presto!!!
Hi Peter, indeed winter has come to an end. We already had the first beautiful days with above 20°C and the next weekend promises unbelievable 28°C. As usual we are boosted from 10°C to 28°C within only few days. You are right, I am using the same epoxy resin for all. I mix a portion of resin and then put half of it into a 2nd pot, where I add micro balloons and thixotropic powder. For the carbon roving at the trailing edge I am using the standard resin without any additive. On the ribs along the trailing edge I am using the epoxy with the micro balloons. For the fibreglass at the wing root I am again using the standard epoxy. For the ribs again the resin with the micro balloons. Keep me updated on your build! Ciao Robert
I wish I could find one of these kits!
Hi, you might check out Aloft Hobbies. They have the fuselage and the speed wing available as separate kits. alofthobbies.com/products/aeronaut-triple-neo-fuselage-kit alofthobbies.com/products/wing-kit-for-aero-naut-triple-speed-model?variant=40019442499721 The thermic wing is only available as in the kit with the (old) balsa fuselage alofthobbies.com/collections/thermal/products/aero-naut-triple-thermic-2-5m-electric-glider
Immer eine Freude dir zuzuschauen. 1. Sahne. Grüße Rudi
Vielen Dank, das freut mich sehr 😄 schöne Grüße Robert
I don't like this video because you are destroying the plane that you just bought I don't know why you 😭😭 spoilt the plan
Destroying things is something I am quite good in 🤣
Nice Build!
Thanks 😊
god this is horrid music, what AI came up with that?
Well that‘s the best that KZread is offering to us poor little content creators that can‘t afford expensive audio licenses 😂
Nice build ... to fix the plan on the table I use transparent adhesive film: easier, in 1 operation you protect the plan and it’s fixed on the table
Thanks 😊 Good idea to use transparent adhesive film. It isn‘t one of my favorite tasks to fix the film on the plan and have it properly tensioned. Do you have a link to the one you use?
Dear sir, thanks for sharing such a beautiful video explaining with practical , I am Jitendra Jadhav from I India, Pune , hobby flyer and I do also aeromodelling,
Thanks a lot for your feedback. I am happy that you liked my video and found it helpful. Many greetings to India
Top Video, hab mir das Video jetzt schon zum 4x angeschaut und werden mir jetzt noch den Flieger holen. Welchen Kleber gibst du bei Minute 28:00 auf die Fläche für das Fieberglas? Muss ich mir auch noch holen. Danke
Vielen Dank! Den Triple Neo kann ich wirklich nur empfehlen, ich fliege ihn immer wieder gerne, sowohl mit den Speed Flächen als auch Thermic Flächen. Der Kleber ist Epoxid Laminierharz. Ich verwende das Epoxidharz L mit Härter L von R&G (www.r-g.de/art/100110)
Sehr schönes Video! Wie lange lässt man den Leim ungefähr trocknen bevor man zum nächsten Schritt kann?
Danke! ☺️ Es kommt darauf an, welchen Leim man nimmt und wie kritisch eine Verklebung ist. Ich benutze Ponal Express, der trocknet relativ schnell. Unkritische Stellen lasse ich ca. 1 Stunde trocknen, kritische Stellen wie z.B. Holm oder die Beplankung lasse ich schon mehrere Stunden oder besser über Nacht trocknen. Wenn man zu früh weiter macht kann sich leichter was verziehen.
Thanks for sharing, enjoyed watching this and it has nudged me a bit closer to making a purchase, think it would make a perfect plane to take for a walk and do some hedge hopping. 👍
Thanks, happy that you liked it and that I could inspire you to possible build the Maverick as well. I still haven't maidened it, but I will for sure do a flight video, so keep an eye on my channel 😀
On my balsa build of the Triple Neo Thermic....I have experienced warping of the wings structure. I am using standard carpenter glue and appropriate weight to hold down the layers as the glue dries. is there a remedy for this warpage?
Hi Peter, on the Triple Neo Thermic I had no issues with warping. In which area is it? There is some chance of recovering the warping during the covering with film by shrinking the film differently strong in order to counteract the warping. Nevertheless you should not expect too much from that. If the warping is really bad you might have to consider removing the part that caused the warping and redo it. Was it caused by the sheeting or was it present before? Were the sheets already warped before glueing? in that case even after using weights and waiting for the glue to fully cure the forces in the sheeting will try to get back to the initial shape which could result in warping. Balsa is normally not so critical but plywood has more power.
Yet another fine build!!! Bravo!!!
Thanks a lot. It was a really nice build experience. I still haven't had the chance to maiden it, but I will do that soon.
Fantastic build!! Thank you for sharing! I bought one of these a few months ago but haven't begun building just yet, glad I didn't now that I have this vid to reference!
Thanks, great that you liked it! Have fun with the build! I enjoyed it a lot.
One of the best fpv videos I've seen. Keep watching over n over
Thanks a lot 😀
beatiful build, unlike the one on my triple neo. also, my wings aren't attacched very well to the fousolage and they flex pretty much by the point they join to the fusolage. any tips to solve it?
Thanks! I also have some flex in the wings but in the area of the fuselage-to-wing joint they should be quite strong. Without further details it is hard to say how to fix. You could send me some pictures to show exactly where the flex is and in which direction it flexes. You can find my mail address in the channel info.
Great vid, with really helpful tips. Many thanks !
Thanks a lot. I am happy that some of my tips are useful. I keep learning with every build and I enjoy sharing it with the community
Its been 50 years since I last built an RC plane. Wish the kits back then were like this. The colour coded sections make it very clear. I have no inclination to get back into the hobby, but this video was very enjoyable to watch and would provide an excellent aid to anyone building the same kit.
Thanks a lot! I built my first kit mid of the 80's, a Graupner Amigo II. Indeed a significant difference to our laser cut kit nowadays. I have learned everything back then from my father and these skills still come in handy even with high precision part in todays kits
The laser printers have improved this hobby immensely!!!
Absolutely! 👍
Great Job, now i need to buy this kit also.
Thanks. I guess you really gotta get one 😜
Fantastic video. The first (and only) model I ever built like this was very satisfying, but I certainly made a few mistakes. Would you classify this as an appropriate second model to build? It's exactly the size and type I would enjoy flying.
Thanks, great that you liked it! There are some key elements for this build, like getting the fuse straight and not warping the control surfaces during covering with film. They require a bit of experience. I would rather say the Maverick is a 3rd than a 2nd model to build. But if you take my video as a guide and go carefully step by step, why not?
I built this model last year, I am still trying to learn how to fly it correctly, I tend to fly it too slowly and find that I keep inducing a stall, when this happens near to the ground damage is caused, so I have had to make some repairs.
I am curious to see how it will fly. I will remember your comment for the first flights and be careful. Have you tried changing the CG and maybe also the angle of attack of the horizontal stabilizer? Both are connected and have a strong influence on the flight characteristics. If the thin fuselage is not perfectly straight your hstab could be a little bit off.
Good tip, I will check it out. Many thanks.@@bavarian_rc
Another great build video. I'm curious what the total build time is from unboxing to ready-to-fly.
Thanks, I am happy that you liked it. Hard to tell what the total build time was. It took me 3,5 months with some periods of more and some with less progress.
@@bavarian_rc Thank you for answering. Truely a labor of love.
Oh yeah, it‘s all about building 😄
Top !
Thanks 😊
War mir wieder eine große Freude Dir zuzuschauen. Grüße Rudi.
Danke, schön dass es Dir gefallen hat! Schöne Grüße Robert
Tolles Video, da steckt sehr viel Arbeit dahinter. Wenn ich mich nicht täusche, dann müsste der Fluss die Wörnitz sein.
Danke ☺️ Richtig erkannt, das ist die Wörnitz.
Your build video really paid off with your flying the Shaka.. I really enjoyed living in your Country years ago.
Thanks! Great that you liked it ... I mean the Shaka and our country 👍😀
Performance art for relaxing!
😊 Great that you liked it!
I'm impressed by the quality of the transformation work - well done. I'm going to have to find one before the sun comes out ;)
Thanks a lot! Go get one for yourself, it’s really a simple and quick build and so much fun to fly. Did you also see my flight video?
@@bavarian_rc Yes, I watched it and it finally made me want to get on with the project :=)
😁👍🏻
The sound track reminds me of Tron.
😂👍🏻
Servus, mal wieder ein geiles Video. Hast du mal vorn den neuen Flixx von aeronaut zu bauen? Lg Tobias
Danke, schön dass es Dir gefällt. Den Flixx hab ich nicht auf meiner Liste. Die ist auch schon ziemlich lang 🤣 Als nächstes kommt der Maverick von Flightpoint (ist schon fast fertig) und danach hab ich schon mehrere weitere Bausätze zuhause. Sieht also eher schlecht aus für den Flixx, ist aber schöner Flieger 👍🏻 würde mir auch gefallen. Schöne Grüße Robert
Moin Robert, schade. Aber freue mich schon über deine neuen Videos. Ich liebe es die Videos zu schauen und selbst nebenbei zu bauen. Danke für deinen Content und deinen fleiß die Videos zu machen.
Vielen Dank, das ist ein tolles Feedback! Wenn ich mal keinen Bock auf selber bauen hab, dann schau ich auch gerne anderen beim Bauen zu 😃