Пікірлер

• 
  @snpatrick7853Ай бұрын

  Most important part? "Wire it up, and your done". SMH...

• 
  @georgebrabec17493 ай бұрын

  Audio is a light light at times, but a good ed video . Plug in the relay flame rectify and I get pilot signal voltage 0.0 volts DC. No stand by or be anything else after relay is plugged into the sub base.

• 
  @RezaVafaei-br4dy3 ай бұрын

  it's very common and hard problem that you resolved and fixed it so very perfect.

• 
  @antonio_g2376 ай бұрын

  Poor audio...

• 
  @fseftv67409 ай бұрын

  That procedure is applicable to other model of fireye?

• 
  @angelruiz5963 Жыл бұрын

  Is the exhaust a drain ?

• 
  @trevorgardner766 Жыл бұрын

  This is a fantastic video. straight to the point. answered all of my questions. Thank you very much

• 
  @lhanif5492 Жыл бұрын

  Thankyou, helepd me

• 
  @Kribananthanaravazhi Жыл бұрын

  Hi, We used the Fireye scanner in the vessel. In Port side Boiler trip due to Flame Scanner B - Flame On Input Fault. Based on our analysis, normally Boiler trip shouldn’t be happened because Flame Scanner A able to Back-Up (every Boiler has two flame scanners : A & B). We trying to check related Wiring Diagram that we have, and we can see Flame Relay in series with Fault Relay. How we can rectify?

• 
  @gregschwartz6886 Жыл бұрын

  Turn the tape around, you can pull it tighter. Turn it upside-down, to apply the pressure.

• 
  @sedp13drewde84 Жыл бұрын

  Can't hear you

• 
  @Nick-xu7gq2 жыл бұрын

  Will the solenoid buzz if it isn't under pressure? I have a new solenoid that is buzzing but we don't have the line full of liquid yet and I'm wondering if I have a bad solenoid.

• 
  @insurroundsound2 жыл бұрын

  Appreciate this video!!

• 
  @thierrydemosthenes22942 жыл бұрын

  OMG ! Thank you so much for this video, very helpful, I'm having the exact same issue in my building.

• 
  @LarryEKG2 жыл бұрын

  Good video, Bill. But how do you account for the fact that a V-controlled charger gradually reduces down to a trickle - it is not a current-controlled charge that suddenly shuts off?

• 
  @bclmax2 жыл бұрын

  wire it up???thats the part i needed ffs

• 
  @abrarmalik63862 жыл бұрын

  Can I use this sov for gas?

• 
  @dmorgan32443 жыл бұрын

  Question is how do you wire it up?

• 
  @maintenanceman26523 жыл бұрын

  Lose trhe red cap break out the zip ties

• 
  @mohammedmusaad76293 жыл бұрын

  There should be pdf attached in description to explain how can such testing combination work in one device

• 
  @howardc65003 жыл бұрын

  The diagnosis and fix are spot on! Try this if your furnace humidifier has the same noise! Thank you!

• 
  @ajiththankachan9493 жыл бұрын

  How to connect the gland to the sov which having female NPT thread and how to do termination?

• 
  @paulwolfe31653 жыл бұрын

  My Asco valve (running pneumatics for a heating system) was making that exact noise so I followed you step for step and found nothing inside to cause and issue and upon rebuilding it makes the same noise... great video, unfortunately it didn't resolve my issue.

• 
  @mdshohelrana25443 жыл бұрын

  why show again and again lockout?

• 
  @haylemariamgebrie6033 жыл бұрын

  Thanks So Much

• 
  @wilfleduc41003 жыл бұрын

  Where is the fire eye in my furnace. And hawe do I clean it.

• 
  @JJRD2224 жыл бұрын

  I like this guy. I hope he is well and smarter than the 99% of the fools wearing masks. I have a feeling he knows better, and refused.

• 
  @JJRD2224 жыл бұрын

  kzread.info/head/PL4618yfPXnK5fkWJRZJDUsdpT6ahIT093

• 
  @JJRD2224 жыл бұрын

  I hope you make it to 100. Hopefully this scamademic doesn't kill you too.

• 
  @alfredogalvez17704 жыл бұрын

  My appliance currently uses spark plugs for flame detection, but detection fails a lot. Is there a position that the spark plug should have or will I have fuel problems?

• 
  @mikegalwa4 жыл бұрын

  You are lifesaviour sir. Perfect explanation. Thank you.

• 
  @thesleepyvegan4 жыл бұрын

  So helpful, an so straightforward!

• 
  @bravomarlon914 жыл бұрын

  the way you applied the teflon tape, handled the pipe wrench, I must say, pissed me off. Nevertheless, very informative.

• 
  @deanmohamed75754 жыл бұрын

  very helpful, thank you

• 
  @br59274 жыл бұрын

  my forklift charger is 20 yrs old working good, getting a new forklift w new battery, should I change the charger also, to protect my investment, does the charger technology as evolved since to charge a 36V 750ah battery?

• 
  @billfischer26014 жыл бұрын

  I would, Most Chargers have capacitors and they go bad after 10-11 years.

• 
  @MrJorrma4 жыл бұрын

  Keep in mind: Charge rate 1/10 of Ah and do not use over 50% of capacity leadacid batteries.

• 
  @jonminnella29664 жыл бұрын

  I have one that works for 10 days and then magically Locs out and you cannot reset it unless you kill the power you can push the reset button all day long it will not reset you have to kill power to the unit and then hold the reset button in after you repower it up seems like some kind of software glitch or electronic issues I replaced this control with a new one and I do not have this problem anymore I would like to get this old one repaired is that something you can do

• 
  @filc-gmail92574 жыл бұрын

  Jon, we do not recommend that any repairs be done to these units as consequences could be bad. You can, however, trade-in the unit for another one. Usually, you get an extra discount for the trade-in. Ask your local distributor if they participate in this plan.

• 
  @jonminnella29664 жыл бұрын

  @@filc-gmail9257 okay how much is that

• 
  @filc-gmail92574 жыл бұрын

  @@jonminnella2966 send us an email to [email protected] to my attention with the model number of your controller and ask for trade-in price. Also, let us know where you are located (City and state).

• 
  @jonminnella29664 жыл бұрын

  @@filc-gmail9257 okay I will do that

• 
  @johnjude26854 жыл бұрын

  Thanks for your teaching,Sir

• 
  @rottenice58374 жыл бұрын

  First

• 
  @Jacronje5 жыл бұрын

  Thank you!!

• 
  @007MegaRoll5 жыл бұрын

  thats how my Subaru Forrester sounds when key turned into pre start position .I have cleaned egr but sound is still there but much quieter than in video but nevertheless. Any feedbacks? what could it be ?

• 
  @master_shake5 жыл бұрын

  nice

• 
  @justinchase1475 жыл бұрын

  Great video! Exactly what I needed to fix my Asco valve.

• 
  @mickseeley46665 жыл бұрын

  Great job and a BIG help for me - thank you!!!!

• 
  @SenorDennis5 жыл бұрын

  How do you wire it??

• 
  @nunyerbidness64174 жыл бұрын

  (crickets chirping)..... There is no wiring instructions included. I guess you're just supposed to guess.

• 
  @eliutcruz14843 жыл бұрын

  ? Did you find out how?

• 
  @powillie2 жыл бұрын

  Green to ground red to black other red to white.

• 
  @Toolie7162 жыл бұрын

  @@powillie how do you know which red is hot and which red is neutral!?!

• 
  @fernandomarinb5 жыл бұрын

  Good your explanation. Good morning my friend. Thanks for your explanation. Did you want to know if after this procedure? The contacts of the relegated The internees must have closed a closed and open? With the profit, the band and the range, do they not carry a value that can work in optimal conditions? Thank you

• 
  @edbertkosidin71826 жыл бұрын

  hello, may i ask how to check if the solenoid is working or not?how to energized it so the solenoid is working? thankyou

• 
  @ALLTESTPro6 жыл бұрын

  To find out more about ALL-TEST Pro's capabilities, please visit www.alltestpro.com, or contact Industrial Equipment Company, an authorized ALL-TEST Pro distributor.

• 
  @ALLTESTPro6 жыл бұрын

  To find out more about ALL-TEST Pro's capabilities, please visit www.alltestpro.com, or contact Industrial Equipment Company, an authorized ALL-TEST Pro distributor.

• 
  @jgkosa6 жыл бұрын

  Perfect. Thanks!

• 
  @pdmacorporation81786 жыл бұрын

  To find out more about electric motor testing visit www.pdma.com The Leader in Electric Motor Testing