Well, I'm trying to. run a 29 tooth Penion. But I can't get it to mesh with both motor mount screws. Running a1650KV. With? My V-2 infraction.
@dgitalchaosКүн бұрын
@@curtiswilliams4501 done people did say 29T wouldn’t fit, so I don’t know if there are different tolerances between batches?
@curtiswilliams4501Күн бұрын
Can you use both of the motor Mount. screws or can you only use one?
@dgitalchaosКүн бұрын
@@curtiswilliams4501 with the 34T pinion and 46T spur, I can only use one screw.
@curtiswilliams4501Күн бұрын
Will a 29 tooth pinion gear fit? The armor infraction V-2 46 spurt.
@dgitalchaosКүн бұрын
@@curtiswilliams4501 I’ve gotten it to fit in every newer 6S Arrma RC I’ve tried. Some say it doesn’t fit. kzread.info/dash/bejne/gIqnlNZql7mTgag.htmlsi=wEubJECRNVUkvRIA
@mitchellminer4596Күн бұрын
Nice run buddy👊👍👍
@dgitalchaosКүн бұрын
@@mitchellminer4596 thanks!
@stuartgray58773 күн бұрын
If the signal you are probing is a serial data bus at 6 Volts, then a square wave (like clock or data) will result in the meter seeing LESS than 6 volts. Because the serial waveform is at zero for about half the time. The meter averages this signal. To really see what's going on, on the serial data lines you need an oscope.
@dgitalchaos3 күн бұрын
@@stuartgray5877 that aspect doesn’t matter for this demonstration, as most people don’t have access to an oscilloscope. The main take away is that if you connect the ESC to either of those two top ports, you WILL fry your receiver.
I need urgent help, connect my Esc to the top port of the Receiver, in the RPM zone and the one that follows, since I did that now when I connect my Esc to the bottom connectors it no longer turns on at all, it's as if There was no signal, and when I plug it into the RPM connector it turns on a permanent red light but not pairing does anything, I press buttons and nothing PLEASE HELP MEEEEEEE
@owhite35014 күн бұрын
Can you provide details on what it took to mount the Maxx lights to the eRevo? It looks very nice.
@dgitalchaos14 күн бұрын
@@owhite350 honestly, I don’t recall. I sold that E-Revo quickly after that mod.
@stingerranger494214 күн бұрын
That pinion and spur mark red on maxx v2 chart it say not recommend to use 26/46 is accelerate at 1.77 sec that would do nice high speed
@BuffaloSoldier-tb9dn17 күн бұрын
Beautiful day!
@troymacleod794421 күн бұрын
I just built a dual motor kraton 6s from the ground up with the 4985 build g it for speed runs. I haven’t run it but it has a 34t spool and 30t pinion… I have no idea what I’m doing but figured two motors could push this a little better and seen people with that set up in the limitless do 80-100 mpg usually on 6s. Any ideas I’m all ears I have all kinds of gears and differentials ?!?!
@dgitalchaos21 күн бұрын
@@troymacleod7944 the main thing is batteries. I’ve gotten the stock system to 106MPH with gearing. I’ve never tried dual motors, but the record holder last time I checked was 221MPH with a single motor. It depends a lot on the road you use and if you can ease into the throttle to keep it from amping out.
@troymacleod794420 күн бұрын
@@dgitalchaos I added a gyro and perfect pass today it’s all ready to go just pinion selection and a few laps on the street see if it shakes anything loss or it’s goi bc straight. Not sure I’ll fit 4 4s seems two 4s 6500 mah and 2 5200 mah is all I’ll fit I have a 9000 mah but it’s too long… lots of people are doing dual motors I think they miss the point that double torque means smaller spool bigger gear potential?!
@troymacleod794420 күн бұрын
Wow 106mph stock I guess it’s apples to oranges but my kraton didn’t go that in km lol on stock but all I did was add a 20t and call it a day
@dgitalchaos20 күн бұрын
@@troymacleod7944 I meant to say I got 106 MPH on the Infraction on 6S with stock electronics. I got 74MPH with the stock electronics on the Kraton 6S, but was just messing around and not really trying for speed. It was super squirrelly above 65MPH due to the stock tires.
@troymacleod794420 күн бұрын
@@dgitalchaos what gears did you use for that was it a spool or 50, 46 t center? Thats amazing
@ikeeiie7826 күн бұрын
You should stand on your tailgate. You could see better signal work better too.
@dgitalchaos26 күн бұрын
@@ikeeiie78 it’s safer too.
@ikeeiie7826 күн бұрын
@@dgitalchaos for sure !
@alantaylor35327 күн бұрын
Awesome.!! 👍 👍 👍 I've just finished my Limitless V2 (my 1st 1/7 RC😁) & I've fitted a Hobbywing 8bl150 G2 6S ESC & a Rocket 4092, 1650kv motor.! Unfortunately it's running way too hot, I've modified a cheap motor slide plate to accept a 26 tooth pinion on the stock 39 tooth spool & I've upgraded to a 34,000 rpm ESC fan & I've got 2 of them on the motor heatsink.! They're only 25mm & 35mm & they do push a lot of air, but I'm getting some 50mm ones to use instead as well as a heatsink that covers the entire motor.!!! I've now ordered a couple of spools to try out, a 42 tooth & a 46 tooth, hopefully they'll help. I'm not looking for a super speed run car, I'm after a reliable daily driver... I'd still like to get around 80 mph out of it... I never usually get my ESCs anywhere near thermal shut off, if it happens I immediately gear down to prevent it.. How safe is it to let your ESC repeatedly go into thermal cut off.??? I'm prepared to get myself a Hobbywing max 6 combo like yours if I can't get the 6S ESC & Rocket motor to work the way I want.! They cost around £230/$295 in the UK, I don't know how much they are in the US. I've been in the hobby for 5 years & I'm totally addicted.. I've got around 50+ RCs of all sizes, prices & types but my biggest, fastest ones so far are my 1/8 Hobao GTS & GTB, my PB is 78 mph using a similar system that I've fitted to my new Limitless.! Like I say, this is my 1st 1/7 scale... I'm EXTREMELY impressed with it so far, it's just on another level altogether.!! 😁😁👍👍 Do you have any tips for these RCs.? Would you recommend any other ESCs or motors.? Thanks for the sweet videos.!! 👍 👍 Subbed & liked & the very best wishes from Scotland 🏴 🙏 ❤️ 📻 🕹️ 🔋 🚗 🚖 🚕 🚔 🚚 🚙 🚘 🚓 🚒 🚑 🚐 🚎 🚤 🚁 🛩️ 👍 👍 👍
@dgitalchaos27 күн бұрын
I wonder if that motor is too large to push the 1650KV motor, which would heat up the ESC quickly. The 8BL150 G2 might be too small for the Limitless to constantly run 80MPH. The gearing your using should net you at least 106MPH if it doesn't amp out first. The 46T spool will help reduce heat and top speed, but even so, I think you'd be constantly pushing the system too much at 80MPH. These Arrma RCs are certainly awesome RCs, with tones of upgrades available. I would recommend the Max 6 G2 and 4990 G2 combo. It's $234 here in the US, but this new Max 6 G2 is much better than the previous version of the Max 6. Even if ran on 6S, with the proper gearing, it'll do 80MPH all day without breaking a sweat.
@alantaylor35327 күн бұрын
@@dgitalchaos Thanks brother, you've basically just confirmed what I was thinking.! That 150 amp ESC & 4092 motor are much better suited to 1/8 scale cars, I'd just be asking too much from them to run a Limitless geared for 80 + mph & I'd eventually kill something. I could set it up to do around 60 mph & it'd be fine I think... But it's a LIMITLESS, why did I bother buying it if I'm not going to make it go fast.?? 😉😁😁... It deserves to have the best gear I can afford to fit in it.! The Hobbywing Max 6 combo is definitely going in next payday.!! 👍 👍 👍 (As much as I'd love to, there's no way I can afford 8S Castle equipment... Well, I mean I could... But I wouldn't be able to go home to the missus for a month 😂 😂.. She's not daft, she knows how much my toys cost).! Those Rocket motors are very good value though, I've got a few of them in all sizes & kv ratings & I'm quiet impressed.. I've noticed that they do run hot though.. Cooling fans & heat sinks are essential.!! I definitely recommend them, also their predecessor, the Surpass KK series motors are very good, I use their 3660, 3670 & 4074 motors paired to a HW Max 10 or WP-SC8 120 amp, 4S ESC in most of my SC & MT rigs & I've hardly ever had any issues with them.! Replace the bearings & they just keep on spinning.!! 👍 👍 They can be picked up for as little as £15/$20 in the UK. Thanks for replying mate.! Please stay safe out there & the very best wishes from Scotland 🏴 🙏 ❤️ 📻 🕹️ 🔋 🚗 🚖 🚕 🚔 🚚 🚙 🚘 🚓 🚒 🚑 🚐 🚎 🚤 🚁 🛩️ 👍 👍 👍
@dgitalchaos27 күн бұрын
@@alantaylor353 a 60 MPH Limitless would be a shame! Again, make sure it's the Max 6 G2 combo with the sensored set up and built in bluetooth. Here in the US, the Max 6 is only a couple dollars more than the previous generation.
@mikepevine3389Ай бұрын
Wow, wherever you live is beautiful!
@dgitalchaosАй бұрын
@@mikepevine3389 thanks! Western Colorado.
@wheeliedad90Ай бұрын
Definitely going this route with my infraction v1 already have the max6 g2 esc! Love the video!
@dgitalchaosАй бұрын
@@wheeliedad90 the 5690 is also an awesome motor.
@wheeliedad90Ай бұрын
Is this the 1650kv 4990sd motor with max6 g2 on 8s? This speed run was amazing keep it up!
@dgitalchaosАй бұрын
@@wheeliedad90 that was the older Max 6 with the previous 1650kv motor. The run with Max 6 G2 and 4990 G2 is here: kzread.info/dash/bejne/mImeyrSFZrC8n9o.htmlsi=Obe1g_1pfB7hEdIF
@wheeliedad90Ай бұрын
@dgitalchaos awesome I really appreciate the reply! I will actually go with the 4990 over the 5690 now thanks!
@dgitalchaosАй бұрын
@@wheeliedad90 they’re both good motors. I did get 127MPH with the 5690 using the Limitless motor mount and a motor plate for the 56 series motor: kzread.info/dash/bejne/amuW1KuamcaemqQ.htmlsi=334Ys6K7jRxkEepK
@antoinefabrega2603Ай бұрын
Hello ! Can you put the part list needed to do the conversion to nitro ? Very cool build i love it !
@dgitalchaosАй бұрын
@@antoinefabrega2603 I don’t have the parts list, but used the center diff carrier from a Hong Nor Sabre X3, as well as the fuel tank, and engine mount. The throttle servo is just on stand off posts with a spare servo I had laying around. Center diff is stock, and I also rotated the front and rear diffs 180°.
@scottm2398Ай бұрын
Way too low of a kv motor for only 3s .. thats only maximum 25,200 rpm, even geared up you're only using half the potential of that motor ..you should be 40,000-50,000 at least if not more..thats a 6s motor , 2000kv x 25.2v fully charged = 54000rpm.
@dgitalchaosАй бұрын
6S was too crazy.
@SilentSassinАй бұрын
@dgitalchaos Nice runs! I'm thinking of doing those clipless mounts, what's the fastest you've gone on the truck with them? Any concerns with them holding up to high speed (130+)
@dgitalchaosАй бұрын
The fastest I’ve gone is 127MPH. Have had zero issues with the clip-less mounts. I use a black paint pen to cover the scratches caused by roll overs when I’m just messing around with it.
@SilentSassinАй бұрын
@@dgitalchaos Awesome, thanks for the feedback and advice
@JamesGratesАй бұрын
Nice pass bud I’d invest in radio link as you get faster you will need range H and w racing channel
@dgitalchaosАй бұрын
I won’t be recommending RadioLink to anyone. I tried the RadioLink RC6G3 V3 with the R7FG receiver and my range was 800 feet, which caused me to damage my Felony body. I sent RadioLink two emails and never received a reply. I returned the RadioLink and 5 receivers to Amazon for a refund. As for speed runs, I did manage to get 127MPH with the stock system. kzread.info/dash/bejne/amuW1KuamcaemqQ.htmlsi=icP0XABPpZZajQ6i
@JamesGratesАй бұрын
@@dgitalchaos well I’m not sure what’s going on with your radio link but we only speed run and are running 2000 to 3000 ft no issues H and w racing channel
@carlosrubio7455Ай бұрын
Hola llevo Max 6 G2 y 4990 , lo he programado sin protección, y 180 km h se me corta y se cae voltaje. Sabes por qué puede pasar???
@dgitalchaosАй бұрын
You might have to accelerate slower to get full speed or might need better batteries. I kept getting 119MPH but did finally manage 120MPH on this system.
@brandonmiller318Ай бұрын
What gearing
@dgitalchaosАй бұрын
Honestly, I don’t remember.
@Revvenge72 ай бұрын
So if I used this on a HPI Trophy Flux 1/8 buggy, what speed you reckon I could do on 3s with 30T or 20T pinion?
@dgitalchaos2 ай бұрын
I’m not sure what your final drive ratio is, but it probably won’t run well with the 30T pinion (cogging) and I’m guessing you’d get about 65-75 with the 20T on 6S.
@Revvenge7Ай бұрын
@@dgitalchaosthanks I've ordered it, will see what happens.
@Danny.fb62 ай бұрын
Mine doesn’t show green light come up after so many tries then it does but then disconnects
@dgitalchaos2 ай бұрын
I wonder if you have a defective unit.
@Danny.fb62 ай бұрын
@@dgitalchaos figured it out lol two apps. Skyrc and GNSS performance analyzer app. Mine worked with the GNSS app lol 👊🏽
@mataflais2 ай бұрын
Very impressive speed on 4s for sure!! Thanks for sharing
@dgitalchaos2 ай бұрын
Not bad at all for such a big motor.
@mataflais2 ай бұрын
I get nervous with the high speed pinion that comes with the infraction giving me like 86mph. Lol. Nice runs bro. And yes that motor sounds great.
@Keif_Stoned2 ай бұрын
Wow the landscape there looks absolutely amazing
@dgitalchaos2 ай бұрын
I love it here!
@user-er8ys5em8w2 ай бұрын
Jesus man breath
@dgitalchaos2 ай бұрын
😂😂 No kidding! I had a bad case of pneumonia when I made the video. Or maybe I’m just a fat blob. Or both.
@micron32683 ай бұрын
Nice passes buddy!👍
@dgitalchaos3 ай бұрын
Thanks!!
@dorsettcook3 ай бұрын
Yes sir
@mataflais3 ай бұрын
beautiful view of mountains and family bro. very interesting vehicle you have there and the way it turns lol. to much for me nice that every one is outdoors lol. saludos.!!!
@dgitalchaos3 ай бұрын
Thanks! It was raining earlier, so we took advantage of the brief warmth.
@Brushlessmarc3 ай бұрын
great run
@dgitalchaos3 ай бұрын
Thanks!
@jh68803 ай бұрын
8:22 you could share data logs?
@dgitalchaos3 ай бұрын
I reset the Infraction to stock and took out the Max 6 G2 combo. Not sure if it would still have the logs after a reset.
@jh68803 ай бұрын
Ok. Just curios rpm/ voltage / current from graph and temps when hit 100% tps. Max6 g2 will keep logs if you dont delete them. Im doing same similar combo. (Max5 g2) Just hit 29500rpm/ 28.5v / 370amps. 110mph 46/46. But loose control after 0.8s 100%
@blaqkyellow3 ай бұрын
You needs a 2 speed gear ⚙️ to get some real speed
@micron32683 ай бұрын
Nice pass buddy, Great work!👍 Subd!
@dgitalchaos3 ай бұрын
Thanks!
@cjchannel12RC3 ай бұрын
Awesome speedrun and congrats on getting an Infraction running a new HW Max 6 G2 combo over 120+mph. I currently have my XO-1 with a Castle MMX8s\1717 combo hoping to get to speedrun her someday when i find a good enough location in OKC.
@dgitalchaos3 ай бұрын
Thanks! Oh man! That’s XO-1 is gonna fly with that combo! I used Google Maps to find several straight roads and checked them out until I found one I liked.
@cjchannel12RC3 ай бұрын
@@dgitalchaos She sure will especially since she's all rebuilt and ready to go. I also got her converted over to mostly V2 spec but left out the a arms and a few other small things. Someday i plan to get an Arrma Felony or Limitless and make it a street basher and speedrunner maybe put the same combo i have in my XO-1 in the Arrma.
@Facts-R-Real3 ай бұрын
Sick! I want to do that.
@dgitalchaos3 ай бұрын
They only lasted about a month of bashing. Too much vibration.
@mataflais3 ай бұрын
very nice record on the Infraction !!!. mine is all stock hitting 62mph lol . and what you said about the body affecting speed runs. I agree with you , air becomes very dense at high speeds!!!, i do speed runs with little cars (like 1/18 scales) and man if i use a truck same setting oor electronics hitting maybe 56 to 57mph, the truck(teton/granite grom) makes a wheele/flips over and is gone. and with like the typhon grom i can hit over 75mph and that thing still on the ground. so yes body or shapes will affect aerodinamics/!!!! again congrats on your new record bro!
@dgitalchaos3 ай бұрын
Thanks!!! You had an awesome run with the Typhon Grom! Makes me want one!
@mataflais3 ай бұрын
@@dgitalchaos u should get one, it's only $140, and u will have lots of fun. And knowing U, probably will hit over 160mph on it. Idk. Lol
@scottdill32683 ай бұрын
Thanks for the great video. i want to do this set up. Do you mind doing a quick video of how you set up your BEC? Showing which wires go where on your Sledge and where you put the BEC etc. Would be helpful. I think I need to do this to speed up the slow servo on both my sledges.
@dgitalchaos3 ай бұрын
I no longer have the Sledge. I’m trying to remember how it was wired, but without having it in front of me, I can’t visualize it.
@scottdill32683 ай бұрын
@@dgitalchaos ok must appreciated. I just want to get all the wires exact. I have never done a BEC.
@dgitalchaos3 ай бұрын
@@scottdill3268 it should be the same as the video, but instead of using the battery like I did, pretend the battery is the ESC and put it in channel 2. Don’t forget that Traxxas receivers have two channel 1.
@Facts-R-Real3 ай бұрын
So can we essentially use the cheaper kit TRA6589 Instead of paying the $100 they want for the XRT or xmaxx TRA7885? It’s not much more power and they are super small LEDs. Am I wrong? Thanks.
@dgitalchaos3 ай бұрын
No, the 6589 uses a 3.3 volt system from the 8028 (which takes one 2S or 3S to power). You’d burn out the lights and module immediately if you connected them to more than 3.3V.
@scottdill32683 ай бұрын
Can you let us know which BEC you put in?
@dgitalchaos3 ай бұрын
It was the Castle 10A BEC, as seen in this video… kzread.info/dash/bejne/oHeTq6iBnMzPldY.htmlsi=m9MB776LgMOtMPKD
@DieselRC873 ай бұрын
What kind of quick release mounts for the body are they,there awesome.
Пікірлер
Well, I'm trying to. run a 29 tooth Penion. But I can't get it to mesh with both motor mount screws. Running a1650KV. With? My V-2 infraction.
@@curtiswilliams4501 done people did say 29T wouldn’t fit, so I don’t know if there are different tolerances between batches?
Can you use both of the motor Mount. screws or can you only use one?
@@curtiswilliams4501 with the 34T pinion and 46T spur, I can only use one screw.
Will a 29 tooth pinion gear fit? The armor infraction V-2 46 spurt.
@@curtiswilliams4501 I’ve gotten it to fit in every newer 6S Arrma RC I’ve tried. Some say it doesn’t fit. kzread.info/dash/bejne/gIqnlNZql7mTgag.htmlsi=wEubJECRNVUkvRIA
Nice run buddy👊👍👍
@@mitchellminer4596 thanks!
If the signal you are probing is a serial data bus at 6 Volts, then a square wave (like clock or data) will result in the meter seeing LESS than 6 volts. Because the serial waveform is at zero for about half the time. The meter averages this signal. To really see what's going on, on the serial data lines you need an oscope.
@@stuartgray5877 that aspect doesn’t matter for this demonstration, as most people don’t have access to an oscilloscope. The main take away is that if you connect the ESC to either of those two top ports, you WILL fry your receiver.
what gps tracker is that?
@@christerberge1287 SkyRC GNSS performance analyzer
I need urgent help, connect my Esc to the top port of the Receiver, in the RPM zone and the one that follows, since I did that now when I connect my Esc to the bottom connectors it no longer turns on at all, it's as if There was no signal, and when I plug it into the RPM connector it turns on a permanent red light but not pairing does anything, I press buttons and nothing PLEASE HELP MEEEEEEE
Can you provide details on what it took to mount the Maxx lights to the eRevo? It looks very nice.
@@owhite350 honestly, I don’t recall. I sold that E-Revo quickly after that mod.
That pinion and spur mark red on maxx v2 chart it say not recommend to use 26/46 is accelerate at 1.77 sec that would do nice high speed
Beautiful day!
I just built a dual motor kraton 6s from the ground up with the 4985 build g it for speed runs. I haven’t run it but it has a 34t spool and 30t pinion… I have no idea what I’m doing but figured two motors could push this a little better and seen people with that set up in the limitless do 80-100 mpg usually on 6s. Any ideas I’m all ears I have all kinds of gears and differentials ?!?!
@@troymacleod7944 the main thing is batteries. I’ve gotten the stock system to 106MPH with gearing. I’ve never tried dual motors, but the record holder last time I checked was 221MPH with a single motor. It depends a lot on the road you use and if you can ease into the throttle to keep it from amping out.
@@dgitalchaos I added a gyro and perfect pass today it’s all ready to go just pinion selection and a few laps on the street see if it shakes anything loss or it’s goi bc straight. Not sure I’ll fit 4 4s seems two 4s 6500 mah and 2 5200 mah is all I’ll fit I have a 9000 mah but it’s too long… lots of people are doing dual motors I think they miss the point that double torque means smaller spool bigger gear potential?!
Wow 106mph stock I guess it’s apples to oranges but my kraton didn’t go that in km lol on stock but all I did was add a 20t and call it a day
@@troymacleod7944 I meant to say I got 106 MPH on the Infraction on 6S with stock electronics. I got 74MPH with the stock electronics on the Kraton 6S, but was just messing around and not really trying for speed. It was super squirrelly above 65MPH due to the stock tires.
@@dgitalchaos what gears did you use for that was it a spool or 50, 46 t center? Thats amazing
You should stand on your tailgate. You could see better signal work better too.
@@ikeeiie78 it’s safer too.
@@dgitalchaos for sure !
Awesome.!! 👍 👍 👍 I've just finished my Limitless V2 (my 1st 1/7 RC😁) & I've fitted a Hobbywing 8bl150 G2 6S ESC & a Rocket 4092, 1650kv motor.! Unfortunately it's running way too hot, I've modified a cheap motor slide plate to accept a 26 tooth pinion on the stock 39 tooth spool & I've upgraded to a 34,000 rpm ESC fan & I've got 2 of them on the motor heatsink.! They're only 25mm & 35mm & they do push a lot of air, but I'm getting some 50mm ones to use instead as well as a heatsink that covers the entire motor.!!! I've now ordered a couple of spools to try out, a 42 tooth & a 46 tooth, hopefully they'll help. I'm not looking for a super speed run car, I'm after a reliable daily driver... I'd still like to get around 80 mph out of it... I never usually get my ESCs anywhere near thermal shut off, if it happens I immediately gear down to prevent it.. How safe is it to let your ESC repeatedly go into thermal cut off.??? I'm prepared to get myself a Hobbywing max 6 combo like yours if I can't get the 6S ESC & Rocket motor to work the way I want.! They cost around £230/$295 in the UK, I don't know how much they are in the US. I've been in the hobby for 5 years & I'm totally addicted.. I've got around 50+ RCs of all sizes, prices & types but my biggest, fastest ones so far are my 1/8 Hobao GTS & GTB, my PB is 78 mph using a similar system that I've fitted to my new Limitless.! Like I say, this is my 1st 1/7 scale... I'm EXTREMELY impressed with it so far, it's just on another level altogether.!! 😁😁👍👍 Do you have any tips for these RCs.? Would you recommend any other ESCs or motors.? Thanks for the sweet videos.!! 👍 👍 Subbed & liked & the very best wishes from Scotland 🏴 🙏 ❤️ 📻 🕹️ 🔋 🚗 🚖 🚕 🚔 🚚 🚙 🚘 🚓 🚒 🚑 🚐 🚎 🚤 🚁 🛩️ 👍 👍 👍
I wonder if that motor is too large to push the 1650KV motor, which would heat up the ESC quickly. The 8BL150 G2 might be too small for the Limitless to constantly run 80MPH. The gearing your using should net you at least 106MPH if it doesn't amp out first. The 46T spool will help reduce heat and top speed, but even so, I think you'd be constantly pushing the system too much at 80MPH. These Arrma RCs are certainly awesome RCs, with tones of upgrades available. I would recommend the Max 6 G2 and 4990 G2 combo. It's $234 here in the US, but this new Max 6 G2 is much better than the previous version of the Max 6. Even if ran on 6S, with the proper gearing, it'll do 80MPH all day without breaking a sweat.
@@dgitalchaos Thanks brother, you've basically just confirmed what I was thinking.! That 150 amp ESC & 4092 motor are much better suited to 1/8 scale cars, I'd just be asking too much from them to run a Limitless geared for 80 + mph & I'd eventually kill something. I could set it up to do around 60 mph & it'd be fine I think... But it's a LIMITLESS, why did I bother buying it if I'm not going to make it go fast.?? 😉😁😁... It deserves to have the best gear I can afford to fit in it.! The Hobbywing Max 6 combo is definitely going in next payday.!! 👍 👍 👍 (As much as I'd love to, there's no way I can afford 8S Castle equipment... Well, I mean I could... But I wouldn't be able to go home to the missus for a month 😂 😂.. She's not daft, she knows how much my toys cost).! Those Rocket motors are very good value though, I've got a few of them in all sizes & kv ratings & I'm quiet impressed.. I've noticed that they do run hot though.. Cooling fans & heat sinks are essential.!! I definitely recommend them, also their predecessor, the Surpass KK series motors are very good, I use their 3660, 3670 & 4074 motors paired to a HW Max 10 or WP-SC8 120 amp, 4S ESC in most of my SC & MT rigs & I've hardly ever had any issues with them.! Replace the bearings & they just keep on spinning.!! 👍 👍 They can be picked up for as little as £15/$20 in the UK. Thanks for replying mate.! Please stay safe out there & the very best wishes from Scotland 🏴 🙏 ❤️ 📻 🕹️ 🔋 🚗 🚖 🚕 🚔 🚚 🚙 🚘 🚓 🚒 🚑 🚐 🚎 🚤 🚁 🛩️ 👍 👍 👍
@@alantaylor353 a 60 MPH Limitless would be a shame! Again, make sure it's the Max 6 G2 combo with the sensored set up and built in bluetooth. Here in the US, the Max 6 is only a couple dollars more than the previous generation.
Wow, wherever you live is beautiful!
@@mikepevine3389 thanks! Western Colorado.
Definitely going this route with my infraction v1 already have the max6 g2 esc! Love the video!
@@wheeliedad90 the 5690 is also an awesome motor.
Is this the 1650kv 4990sd motor with max6 g2 on 8s? This speed run was amazing keep it up!
@@wheeliedad90 that was the older Max 6 with the previous 1650kv motor. The run with Max 6 G2 and 4990 G2 is here: kzread.info/dash/bejne/mImeyrSFZrC8n9o.htmlsi=Obe1g_1pfB7hEdIF
@dgitalchaos awesome I really appreciate the reply! I will actually go with the 4990 over the 5690 now thanks!
@@wheeliedad90 they’re both good motors. I did get 127MPH with the 5690 using the Limitless motor mount and a motor plate for the 56 series motor: kzread.info/dash/bejne/amuW1KuamcaemqQ.htmlsi=334Ys6K7jRxkEepK
Hello ! Can you put the part list needed to do the conversion to nitro ? Very cool build i love it !
@@antoinefabrega2603 I don’t have the parts list, but used the center diff carrier from a Hong Nor Sabre X3, as well as the fuel tank, and engine mount. The throttle servo is just on stand off posts with a spare servo I had laying around. Center diff is stock, and I also rotated the front and rear diffs 180°.
Way too low of a kv motor for only 3s .. thats only maximum 25,200 rpm, even geared up you're only using half the potential of that motor ..you should be 40,000-50,000 at least if not more..thats a 6s motor , 2000kv x 25.2v fully charged = 54000rpm.
6S was too crazy.
@dgitalchaos Nice runs! I'm thinking of doing those clipless mounts, what's the fastest you've gone on the truck with them? Any concerns with them holding up to high speed (130+)
The fastest I’ve gone is 127MPH. Have had zero issues with the clip-less mounts. I use a black paint pen to cover the scratches caused by roll overs when I’m just messing around with it.
@@dgitalchaos Awesome, thanks for the feedback and advice
Nice pass bud I’d invest in radio link as you get faster you will need range H and w racing channel
I won’t be recommending RadioLink to anyone. I tried the RadioLink RC6G3 V3 with the R7FG receiver and my range was 800 feet, which caused me to damage my Felony body. I sent RadioLink two emails and never received a reply. I returned the RadioLink and 5 receivers to Amazon for a refund. As for speed runs, I did manage to get 127MPH with the stock system. kzread.info/dash/bejne/amuW1KuamcaemqQ.htmlsi=icP0XABPpZZajQ6i
@@dgitalchaos well I’m not sure what’s going on with your radio link but we only speed run and are running 2000 to 3000 ft no issues H and w racing channel
Hola llevo Max 6 G2 y 4990 , lo he programado sin protección, y 180 km h se me corta y se cae voltaje. Sabes por qué puede pasar???
You might have to accelerate slower to get full speed or might need better batteries. I kept getting 119MPH but did finally manage 120MPH on this system.
What gearing
Honestly, I don’t remember.
So if I used this on a HPI Trophy Flux 1/8 buggy, what speed you reckon I could do on 3s with 30T or 20T pinion?
I’m not sure what your final drive ratio is, but it probably won’t run well with the 30T pinion (cogging) and I’m guessing you’d get about 65-75 with the 20T on 6S.
@@dgitalchaosthanks I've ordered it, will see what happens.
Mine doesn’t show green light come up after so many tries then it does but then disconnects
I wonder if you have a defective unit.
@@dgitalchaos figured it out lol two apps. Skyrc and GNSS performance analyzer app. Mine worked with the GNSS app lol 👊🏽
Very impressive speed on 4s for sure!! Thanks for sharing
Not bad at all for such a big motor.
I get nervous with the high speed pinion that comes with the infraction giving me like 86mph. Lol. Nice runs bro. And yes that motor sounds great.
Wow the landscape there looks absolutely amazing
I love it here!
Jesus man breath
😂😂 No kidding! I had a bad case of pneumonia when I made the video. Or maybe I’m just a fat blob. Or both.
Nice passes buddy!👍
Thanks!!
Yes sir
beautiful view of mountains and family bro. very interesting vehicle you have there and the way it turns lol. to much for me nice that every one is outdoors lol. saludos.!!!
Thanks! It was raining earlier, so we took advantage of the brief warmth.
great run
Thanks!
8:22 you could share data logs?
I reset the Infraction to stock and took out the Max 6 G2 combo. Not sure if it would still have the logs after a reset.
Ok. Just curios rpm/ voltage / current from graph and temps when hit 100% tps. Max6 g2 will keep logs if you dont delete them. Im doing same similar combo. (Max5 g2) Just hit 29500rpm/ 28.5v / 370amps. 110mph 46/46. But loose control after 0.8s 100%
You needs a 2 speed gear ⚙️ to get some real speed
Nice pass buddy, Great work!👍 Subd!
Thanks!
Awesome speedrun and congrats on getting an Infraction running a new HW Max 6 G2 combo over 120+mph. I currently have my XO-1 with a Castle MMX8s\1717 combo hoping to get to speedrun her someday when i find a good enough location in OKC.
Thanks! Oh man! That’s XO-1 is gonna fly with that combo! I used Google Maps to find several straight roads and checked them out until I found one I liked.
@@dgitalchaos She sure will especially since she's all rebuilt and ready to go. I also got her converted over to mostly V2 spec but left out the a arms and a few other small things. Someday i plan to get an Arrma Felony or Limitless and make it a street basher and speedrunner maybe put the same combo i have in my XO-1 in the Arrma.
Sick! I want to do that.
They only lasted about a month of bashing. Too much vibration.
very nice record on the Infraction !!!. mine is all stock hitting 62mph lol . and what you said about the body affecting speed runs. I agree with you , air becomes very dense at high speeds!!!, i do speed runs with little cars (like 1/18 scales) and man if i use a truck same setting oor electronics hitting maybe 56 to 57mph, the truck(teton/granite grom) makes a wheele/flips over and is gone. and with like the typhon grom i can hit over 75mph and that thing still on the ground. so yes body or shapes will affect aerodinamics/!!!! again congrats on your new record bro!
Thanks!!! You had an awesome run with the Typhon Grom! Makes me want one!
@@dgitalchaos u should get one, it's only $140, and u will have lots of fun. And knowing U, probably will hit over 160mph on it. Idk. Lol
Thanks for the great video. i want to do this set up. Do you mind doing a quick video of how you set up your BEC? Showing which wires go where on your Sledge and where you put the BEC etc. Would be helpful. I think I need to do this to speed up the slow servo on both my sledges.
I no longer have the Sledge. I’m trying to remember how it was wired, but without having it in front of me, I can’t visualize it.
@@dgitalchaos ok must appreciated. I just want to get all the wires exact. I have never done a BEC.
@@scottdill3268 it should be the same as the video, but instead of using the battery like I did, pretend the battery is the ESC and put it in channel 2. Don’t forget that Traxxas receivers have two channel 1.
So can we essentially use the cheaper kit TRA6589 Instead of paying the $100 they want for the XRT or xmaxx TRA7885? It’s not much more power and they are super small LEDs. Am I wrong? Thanks.
No, the 6589 uses a 3.3 volt system from the 8028 (which takes one 2S or 3S to power). You’d burn out the lights and module immediately if you connected them to more than 3.3V.
Can you let us know which BEC you put in?
It was the Castle 10A BEC, as seen in this video… kzread.info/dash/bejne/oHeTq6iBnMzPldY.htmlsi=m9MB776LgMOtMPKD
What kind of quick release mounts for the body are they,there awesome.
www.amazon.com/gp/aw/d/B09GV84TC9?psc=1&ref=ppx_pop_mob_b_asin_title
How did you fit that size motor without hitting steering?
What body clip system is that?
How did you get that motor to fit with out hitting steering??
Using the stock Arrma mount, it fit right in for me.
Castle esc can be changed to put out the 7.4 volts, right?
Yes, from 5V to 9v, but requires the CasteLink and a PC. The newer one can be programmed via a Bluetooth module.
JQS
Correct
Tell me more about that Hidden Valley Ranch...
en.m.wikipedia.org/wiki/Ranch_dressing
Is the Traxxas what the Baja Bandit was?
I honestly have no idea.
Bro didn't know laminar flow