1/7 Infraction speed run with Max 6 G2 5690 combo - 6S run - 106MPH
Ғылым және технология
Running the Infraction on 6S with the Max 6 G2 and 5690 1250kv G2 motor with 42 pinion and 35 spur. Using two brand new Hovoo 5500mAh 120C lipos. I was impressed with how many runs I could do back and forth (11 total - not all filmed). Being 45°F, I thought these lipos would amp out, but they held fine, even though they’re only using 12 gauge wire to the EC5 connectors.
Пікірлер: 21
That things running great! I’m trying to get out to run my limitless with my 2 little boys but it’s not easy!
@dgitalchaos
4 ай бұрын
My son loves to watch, but my daughter doesn’t care for them. I did manage 124MPH on 8S, but my GoPro was aimed too high 😕
@FEboats
4 ай бұрын
@@dgitalchaos awesome man!
Really good pases I’m looking to do same speed but on 8s currently running 40spur 27pinion just waiting for some scorched drive shaft
@dgitalchaos
5 ай бұрын
Nice! The street was busier than usual, but by the time I went back later in the evening, it started raining, so I didn’t run 8S. Which motor/ESC are you running?
@dgitalchaos Nice runs! I'm thinking of doing those clipless mounts, what's the fastest you've gone on the truck with them? Any concerns with them holding up to high speed (130+)
@dgitalchaos
18 күн бұрын
The fastest I’ve gone is 127MPH. Have had zero issues with the clip-less mounts. I use a black paint pen to cover the scratches caused by roll overs when I’m just messing around with it.
@SilentSassin
18 күн бұрын
@@dgitalchaos Awesome, thanks for the feedback and advice
How did you make the 5690 fit? I believe the stock mount can only fit a 4985 or 4990. And does a 90mm lenght motor fit?
@dgitalchaos
4 ай бұрын
I used the motor mount from the limitless with the 56 series motor plate. It’s a direct fit in the infraction without needing to drill. The 90mm motor fits with about 1mm gap between the motor and steering assembly.
@thomweber4102
4 ай бұрын
@@dgitalchaos so basicly only the motor plate needs to be bigger, and use the stock motor slider ( aluminium part that also hold the center diff or spool)
@dgitalchaos
4 ай бұрын
@@thomweber4102 the stock diff / motor mount won’t work. The one from the limitless is larger and fits the larger motor plate. You’d need this part: jennysrc.com/collections/arrma-limitless-ara7116v2/products/arrma-limitless-v2-6s-red-mount-infraction-outcast-talion-motor-typhon-ara7116v2 And this part: www.amazon.com/gp/aw/d/B0BR8M1QSJ?psc=1&ref=ppx_pop_mob_b_asin_title
@thomweber4102
4 ай бұрын
@@dgitalchaos many thanks!
What are you amp numbers under full throttle.
@dgitalchaos
4 ай бұрын
On 6S, I peaked at 241 amps at full throttle, on 8S, I peaked at 402 amps.
@Nelsonmccallum27
4 ай бұрын
@@dgitalchaos nice I just bought the same set up and I was wondering that it might still cut out, how long do you hold 100%
@dgitalchaos
4 ай бұрын
@@Nelsonmccallum27 it only held for .06 seconds before cutting out on an 8S run. Batteries dropped to 2.9V/cell, so better batteries would help. After the amp out, batteries went back to 3:93V/cell.
@Nelsonmccallum27
4 ай бұрын
@@dgitalchaos that’s good info thanks for sharing. I literally have the same motor and esc. But I’m using CHNL 5200 4s ic5 packs 90c with 180burst, I held 100% for 1.04 seconds and peak was 340amp and 244 at the end with 3.375volts per cell. And it came back to 4.1 after.
@dgitalchaos
4 ай бұрын
@@Nelsonmccallum27 awesome! I was wanting a set of those batteries. What was you maximum speed?