Пікірлер

• 
  @ElectronicBanana404Ай бұрын

  Why did you guys discontinue these boards I needed them for a project and can't find anything as small or as simple

• 
  @santoshnaik9397Ай бұрын

  Which grease we can use for long life

• 
  @haikal2886Ай бұрын

  thank youuuuuuuuuuuuu very helpful

• 
  @ultimatums1Ай бұрын

  what kind of servo/linear actuators do airplane spoilers use? how can they extend that fast?

• 
  @yoBradyO112 ай бұрын

  Every one of these videos. Nobody specifies whether the narrow side of the crimper and goes towards the front of the connector or not. I've pinched off the wires I'm trying to connect three times already

• 
  @blakew41422 ай бұрын

  Hi I need a linear actuator with 6000N that can adjust limit. I don’t wanna burn it out and I don’t wanna spend a ton of money! Anyone got ideas ? Off Amazon maybe?

• 
  @garypate32012 ай бұрын

  Soooo what size servo uses a 25t horn? I’m trying to find aluminium horns for mks micro servos

• 
  @tedbastwock38102 ай бұрын

  Is it ok to reverse the diodes so the cathodes face one another instead of the anodes?

• 
  @alexanderkhazaradze48622 ай бұрын

  Great Video! Question - what do you call a momentary switch that can switch forward and backwards vs a switch that could be just in forward or backward position?

• 
  @ahmednadeem53322 ай бұрын

  Thanks Dear... It helped me a Lot.. May you Live Happy Always 🙂

• 
  @SiboBushings3 ай бұрын

  Interesting video 😊

• 
  @clypeum50633 ай бұрын

  When you Take Out the screw and rotate the whole assembly you lose your factory marking.

• 
  @synthead4 ай бұрын

  A couple questions! What is the noise rating on the servo? Also, if I were to open the servo and move the limit switch on the fully-extended side (desolder, drill, solder), would the servo have a correctly-functioning shortened range? I'm looking to do ~85 lbs with a ~1.5" throw and it would be excellent to have the safety in hardware, not software.

• 
  @profBricks4 ай бұрын

  How about the position of the pivot when the skid steer spins "in place"?

• 
  @TW394 ай бұрын

  Do I need a gearbox with this if I'm gonna use it on a rc 110scale crawler chassis

• 
  @OG_peanut4 ай бұрын

  is there another mechanism that preforms the same but smaller and compact?

• 
  @HannahSpring5 ай бұрын

  With your Ball bearings and mounts, would you have any mounts that can be fitted to the floor and ceiling, with the rod being exposed out of the ceiling for a small DC Generator, plus a outer shell to go over the rod with a plate for a base to be mounted for a plate??

• 
  @Swenser5 ай бұрын

  I need to mount wheels on a 775 motor that spins high revs for tennis ball machine launcher. I'm struggling to find appropriately matching couplers and wheels to give a balanced outcome. Any tips on the most ideal way.

• 
  @romarioariza87065 ай бұрын

  thank you so mach

• 
  @abdallahtlayss86016 ай бұрын

  احسنتم يا شباب اعجبني

• 
  @captainagk6 ай бұрын

  came hear to learn about linear bearings got distracted by the perfect cnc cut helmet you are wearing.

• 
  @alexcoulter13846 ай бұрын

  What is the difference between skid and differential steering? Is it just the number of wheels?

• 
  @rodrigoalexanderaiquezelad54096 ай бұрын

  I wonder the same.

• 
  @richosvideos9117 ай бұрын

  Ive just used the on an rc retract system they work fantastic!

• 
  @vergatronik8 ай бұрын

  Hi Kyle 😍

• 
  @diegogarridomendoza28288 ай бұрын

  Thank you! What brand and model is the dpdt hd momentary switch? I need one to control the direction for a 3D printer stepper motor.

• 
  @davidstokes54818 ай бұрын

  GREAT VIDEO! I want to put an actuator on my lawnmower deck. How do I calculate the size, travel, and strength needed? The mower deck is roughly 200 lbs. Thanks!

• 
  @omsingharjit8 ай бұрын

  Why there is play in lm8uu based linear rail , I measure the diameter of different roads all diameter is less than 8mm it's around 7.6 to 7.8 mm is it common tolorance or perfect 8mm rods are also available??

• 
  @bradleylomas75259 ай бұрын

  Cool. Looks like a blast!

• 
  @douglaskalous92879 ай бұрын

  who do you size the diode?

• 
  @KFLson9 ай бұрын

  You forgot to show us what tools to use for each screw 🙌😭

• 
  @christophermariolaferla21989 ай бұрын

  Is there any way I can solve the problem? Thank you. Regards

• 
  @Sparky59 ай бұрын

  These are obsolete and you don't even sell them anymore. I'm looking for a video on the new gearboxes sold by ServoCity.

• 
  @ServoCity9 ай бұрын

  We will put a new video on the docket! Thank you for mentioning it.

• 
  @Videolinquency9 ай бұрын

  Very useful. Thank you.

• 
  @christophermariolaferla21989 ай бұрын

  Good afternoon. Re. Hitec HS-785HB servo. I had this servo since 2008 and it always worked fine. Suddenly it went mad. It goes from end to end without stopping at any stick position. Any advice on how to fix the problem.. Thanks and regards C. M. La Fery

• 
  @ServoCity9 ай бұрын

  Hello, It sounds like the feedback pot has become disconnected from the output shaft. Hard to know for sure, but that can create the behavior I think you're experiencing.

• 
  @TravisFPV2 ай бұрын

  @@ServoCity I'm having a similar issue with my HS-785HB. Except I believe when I ordered mine, I had it modified for continuous rotation. And now, it just keeps spinning in one direction and never stops, regardless of what commands I send it.

• 
  @nakiradu779 ай бұрын

  Thanks

• 
  @raffmini10 ай бұрын

  For my application I need 2, of the 2" Stroke 115 lb Thrust Heavy Duty Linear Actuator, I wanted to know if I could use a, "Thrustmaster USB Joystick (PC)", or which one do you recommend. I don't understand much. I have seen your video. Thanks Raffaele

• 
  @mel14sky10 ай бұрын

  thanks for the help 👍 amazing moustache btw

• 
  @guliyevshahriyar10 ай бұрын

  thx for the series!

• 
  @MAGA-Chad10 ай бұрын

  I love how smooth the animation is. Also I'm a bit new with these worm gears but I did have a couple questions about them. 1. Is it possible to have a 4:1 or 5:1 ratio with a worm gear? I've been told the lowest they can go is 10:1 but I figured I'd ask the experts. 2. Can these worm screw gears work with bevel gears as well? And if they can, can two bevel gears be used on both sides of the worm screw gear?

• 
  @elywickander46669 ай бұрын

  The reason why you can't really go lower than 10:1 is because the gear ratio of a worm drive is equivalent to [the number of teeth on the gear]:1. A 4 or 5 tooth gear just can't work, so that's why there's that limitation. As for the bevel gear question, I don't really see any reason why you would want to use a bevel gear since you can already put that gear at any orientation around the worm. And yes, you could have multiple gears running off the same worm as long as you can fit them.

• 
  @T-FLoWW10 ай бұрын

  Where can i find those wheels

• 
  @rayvolpe311010 ай бұрын

  I bought an actuator for my boat trim motor and it lasted about 3 weeks before it died. I made sure it was water proof and then I also sprayed it with water proofing. So that is one thing you forget to mention. It had much more dynamic and static load rating than I needed and was the correct voltage. It was slow but I would rather slow than not enough lift. Anyway, I would be interested to know what went wrong. The company had a 30 day return but by the time I was able to install I really only got about 3 weeks out of it and maybe had to lift the motor 8 times during that period. Can you comment on what may have/could have gone wrong ?

• 
  @933pilgrim10 ай бұрын

  HELP please! Bought second hand metal gear servos with metal arm and now need to replace arms. But cannot remove them at all. may be they are on thread locker? What you suggest - how to remove the arms? Its Power HD 1501 MG analog servo. Thanks

• 
  @Stubby026610 ай бұрын

  Could you show on how to set up the same system but using relays for higher amperage circuits where the switches, using less amps, to trip the relays to run the motor?

• 
  @tonoreyes707711 ай бұрын

  hola ya hice todo paso a paso conforme a las imagenes cargue el codigo en el arduino micro y en el arduino uno pero no se mueve el carro estoy utlizando motores polu de 300rpm pero no funciona no se mueve le tengo que poner motores de 145 rpm para que se pueda mover o puede hacer un video mostrando paso a paso como hacerlo con las conexiones y programacion

• 
  @nathanmccorkle427811 ай бұрын

  I've got a Microzone MC7 transmitter that I'm trying to use to drive a two-motor dual tracked vehicle. Now I think I'm prepared to do some experiments tomorrow, thanks!

• 
  @rickc162611 ай бұрын

  Thank you! I’m an amateur (very amateur) builder and I’m putting together an electric outboard, but I’ve never used thrust bearings before in my life! Your explanation of how they’re used is so concise and simple to understand and will let me finish my project.

• 
  @vincenzostasi187411 ай бұрын

  Dove si possono acquistare grazie

• 
  @futureconsequence537411 ай бұрын

  Great Info! Thanks!

• 
  @23youwatch Жыл бұрын

  such a great video! Execllent explaination

• 
  @danielnordstrand6443 Жыл бұрын

  In Australia, we call them two different names (bolt or screw) so we always know the style your talking about ;p