Did you run the hall test routine in the mqcon app?
@Chinhnguyen04974 күн бұрын
the frame are so expensive. I think if you have a blueprint, you can hire someone else to cut and weld it with better materials, probably still at the same price
@T2daBikeGuy5 күн бұрын
Will a 17 inch hub motor work with the 19 inch front wheel
@godusopp69406 күн бұрын
Got to be a cheaper place to get a frame
@lewis_rides26 күн бұрын
why dont you add pegs?
@user-vi2kx8ec3t28 күн бұрын
If the swing arm is 177 mm and the wheel motor is 155 mm, how is the installation done?
@CordaeWАй бұрын
Hey my friend just recently wrecked mine and I have fixed everything so far all I need now is new forks(they got split in half) what is a good website for the front forks, I really need them
@CordaeW17 күн бұрын
Nevermind got the ones you got
@jesusdeabreu4436Ай бұрын
The best setup bro❤
@lil_cali8132Ай бұрын
How do you install the rear light
@lil_cali8132Ай бұрын
How did you install the rear lights
@ModModRcАй бұрын
Please help me with a chain. I want a gold 1. What size & strength do I need? Allt je AliExpress ones say 7,8,-12s on them
@soapbullet-tq8zfАй бұрын
How fast the hub motor get hot ? I have 60v3000w hub motor and 60v45-50amp controller and my motor hub get 70deg after 4-5 miles of driving is this normal?
@bmkro2 ай бұрын
what throttle are you using? the one that comes in the kit with the rear wheel? if so is it a half hand or whole hand throttle?
@user-sz3wc1xd1b2 ай бұрын
The brake mounting bracket on the Zoom brakes is 51mm, but the mounting points on the forks is 75mm. Did you use an adapter?
@christianmcgunagle83842 ай бұрын
what size are the bolts for the rear show on aliexpress, about to order mine but i want to make sure im getting the right size, i have the same frame
@dtrh95463 ай бұрын
Isit possible to mKE 1 like this 1000w/?
@user-uh4di9ez7p3 ай бұрын
Where did you get those things on your motor, please send me the link!!
@tylercrane40053 ай бұрын
Where did you buy the bike
@alexanderbegg49784 ай бұрын
Love your content keep it up
@floo86044 ай бұрын
How’d u get the fender to fit? Did u use larger screws? I have the same forks but the fender doesn't fit at all
@benrendell38575 ай бұрын
nice video man i enjoyed it
@DehydratedCactusDC5 ай бұрын
Good
@PapaDutch5 ай бұрын
I subbed so that I don't lose this parts list! I'm also working on an S/B frameset with 200mm rear clearance for a 19" NBPower QS273 and was thinking real hard about the front end setup... I honestly think this bike is going to be scary
@arthurbal5 ай бұрын
Just changed my front end out to 2023 surron forks that I found for very cheap locally and man are they better then the zoom forks. Definitely would recommend getting a good front end setup.
@Barefoot-Bob6 ай бұрын
where did you get the moto seat ?
@500wattz6 ай бұрын
Not a fan of that charging port location. My clone has it at the top where gas would go in. Nice build dude. How hot does your controller get under full load, full speed and going uphill?
@mgtowlevel52935 ай бұрын
Yes!
@arthurbal5 ай бұрын
I don't have any hills in my area so I can't really tell you how hot it gets under serious load but I am usually going full throttle or sending it on trails and I've had no over heating issues at all.
@graychenault14356 ай бұрын
Thanks for this! And also to all the other commentors!
@E-supermoto7 ай бұрын
The issue is the battery.. sorry to be the one to say it but the battery doesnt have enough output off what the controller needs. So try tuning it down or buy a bigger battery
@voodoochild67417 ай бұрын
Have you ever fixed that wobbly rear wheel? What caused it?
@cameronprutzman72227 ай бұрын
Also what about cranks
@cameronprutzman72227 ай бұрын
What about the charger link
@isaiahpopper22568 ай бұрын
Where is part twoooo
@arthurbal5 ай бұрын
I've been too lazy to edit it but hopefully tomorrow or Saturday!
@feltar12968 ай бұрын
Hi have u go link for charger thanks
@NorthernMafioso8 ай бұрын
Why do much just built mine for 2k
@bigsmoke5094 ай бұрын
What parts you used?
@user-jr9oo7zq9r9 ай бұрын
How did you get the front fender to attach ? What the adapter ?
@mikeangel70049 ай бұрын
Where you get the axle for the front and back
@lilyun34899 ай бұрын
Could you please tell me what size you bought the special bolts you mentioned in the video, 18mm or 33mm, or which one? Great video, BTW!
@graychenault14356 ай бұрын
measure your bracket spacing
@douglaswordingham90409 ай бұрын
were can I buy a mqcon controller 72v 150 amp 8000 watt controller from ,am in uk
@ourworldmridgaf777410 ай бұрын
Hey bro where can I get these type of spacers for the kick stand? Or what’s the name of these kind of spacers
@ourworldmridgaf777410 ай бұрын
Bro do you have to brake in these brakes or something ? 😂 I bought them and tried them out but they aren’t as good ..
@Quinteros77710 ай бұрын
I just installed my Sabvcon controller SVMC 7260 but I cannot get my bike to go pass 15m/h (25km/h). Would you know if it is a connection error on my part or perhaps a setting issue?
@stealthbomber984110 ай бұрын
do you have a contact number? I have the same sthealth Bomber model but I have some questions, could you help me?
@CrunchyCheeseMC11 ай бұрын
hello, i am building a similar bike to yours but i am using 20in bicycle tires. How high is your 19in build? if i buy the front wheel that say on amazon it is a disk break will I be able to put hydraulic breaks on it?
@raylivengood804011 ай бұрын
I had a similar issue setting up my controller and motor. The “thumping” is sort of like a misfire. I’m guessing it’s a unstable magnetic field. This also occurs at higher rpm.
@aaron0920008 ай бұрын
Did you manage to find the cause of the issue and fix it?
@raylivengood80408 ай бұрын
@@aaron092000 I was told that my aftermarket controller was a sinewave, but in fact it was a square wave. I was dealing with a AliExpress seller.. I was a little bit miffed, but pushed through with the seller until they gave me a discount on a sinewave. No problem since. Another issue I was having was with the throttle /display. The old square waves were frying them or something. I still don’t understand how that happened.
@kaiko42811 ай бұрын
Hi im form poland and i wanted to ask if there is any possibility to deliver the frame to polish? unfortunately, aliexpress ebay and amazon do not deliver to Poland. are any thoughts?
@allahuakbar421720 күн бұрын
If you can go online you can get the measurements from the advertisement. Then go and ask welders in your country to make the frame
@Killer-wu9hk11 ай бұрын
Can some one explain to me what the, "hull test" (idk if that's correct) is?
@imho725011 ай бұрын
Hall Test. This is the self learning feature of the Sabvoton. You connect phase and hall wires in any order (but professional will color match them from the motor to controller), then run test, and the controller will pair the motor to itself. After that if the motor runs backwards you just open the app and select “reverse” to make it run correct direction. The Hall phase shift will appear after the test. Not to be confused with commutation angle of 60 or 120.
@Killer-wu9hk11 ай бұрын
@@imho7250 that's for the explication, I don't get everything that's mentioned here but i think I'll manage with this explication and some vids of how it works, tryna get my fist DIY ebike working
@imho725011 ай бұрын
@@Killer-wu9hk , to make any controller work, it needs battery power connected, the motor phase and hall sensor connectors connected, the throttle connected, and the ignition wire connected. From there you should be able to open the MQCON app and verify voltage settings match your battery. Then with the rear wheel off the ground you would run the hall test, and the motor will start moving slowly as it checks the relationship between the phases and the hall sensors. After it finishes, and you save it, the motor should run. Of the motor runs forward then its correct, if it runs backwards then in the app you can change the direction. You never need to change any phase wires or hall wires after the initial color matching of all 8 wires. Any mismatch will be fixed inside the controller.
@Killer-wu9hk11 ай бұрын
@@imho7250 I'm not sure if the controller will connect to the app because, I bought the bike off alibaba from a company called keyu, they seem reputable because they have their own ebike frame and several types of it, the description mentioned a 25a sabvoton controller, my bike 3000w so ima need an upgrade but when I asked about the controller they said 45a keyu controller, I've never heard of a keyu controller, maybe they made a mistake and ment 45a sabvoton or 25a. Also the low showered sabvoton controllers are not Bluetooth compatible, you have to use the computer app, but there's no tutorials about that
@imho725011 ай бұрын
@@Killer-wu9hk , if you make a KZread video showing what you have it’s easier to help. There are many controllers. Votol and Kelly need a computer. Sabvoton and Fardriver and YuYangKing use Bluetooth and a phone app.
@bofa3321 Жыл бұрын
Top speed??? Awesome build
@arthurbal5 ай бұрын
50MPH
@DrugChovek Жыл бұрын
You make very good videos, but you have to post more regularly to grow the channel. I believe in you bro, keep going!
@eddieramirez435 Жыл бұрын
Wtf why would you think it's the controller? 😂 All wheel inside or spokes.
@aaron0920008 ай бұрын
It's the bms lol
@rccrazy8 ай бұрын
It can't be the bms because I run lipos without bms and I have the same issue on one of my bikes. It's a wire combination issue or loose wire maybe.
@aaron0920008 ай бұрын
@@rccrazy what lipo battery's do you have? Alot if not most of the good ones have built in chips for over discharge protection. Though they don't protect against rouge charging.
@rccrazy8 ай бұрын
@aaron092000 most lipos have no form of over discharge protection it's the esc that has the voltage protection parameters and change them with a balance charger. And I use 2 lots of 5 x 9500mah 4s HRB lipos to get 19ah 72v or 20s.
@aaron0920008 ай бұрын
@@rccrazy yeah my bad your right, most don't have discharge protection. Done abit of research and found that some have balance chips inside which could be the case for you 😀 I think maybe like you said, wire combination or phase wires crossing causing unstable magnetic field? Or possibly voltage sag causing the lipo to trip out? I'm curious have you found the solution to this issue? From my experience I was running a 30a bms with 60a peak and when I tried to run over 60a through it, it would do the same thing shown in this video, like a rev limiter on a car. it would only happen once I reached a certain speed too
Пікірлер
Did you run the hall test routine in the mqcon app?
the frame are so expensive. I think if you have a blueprint, you can hire someone else to cut and weld it with better materials, probably still at the same price
Will a 17 inch hub motor work with the 19 inch front wheel
Got to be a cheaper place to get a frame
why dont you add pegs?
If the swing arm is 177 mm and the wheel motor is 155 mm, how is the installation done?
Hey my friend just recently wrecked mine and I have fixed everything so far all I need now is new forks(they got split in half) what is a good website for the front forks, I really need them
Nevermind got the ones you got
The best setup bro❤
How do you install the rear light
How did you install the rear lights
Please help me with a chain. I want a gold 1. What size & strength do I need? Allt je AliExpress ones say 7,8,-12s on them
How fast the hub motor get hot ? I have 60v3000w hub motor and 60v45-50amp controller and my motor hub get 70deg after 4-5 miles of driving is this normal?
what throttle are you using? the one that comes in the kit with the rear wheel? if so is it a half hand or whole hand throttle?
The brake mounting bracket on the Zoom brakes is 51mm, but the mounting points on the forks is 75mm. Did you use an adapter?
what size are the bolts for the rear show on aliexpress, about to order mine but i want to make sure im getting the right size, i have the same frame
Isit possible to mKE 1 like this 1000w/?
Where did you get those things on your motor, please send me the link!!
Where did you buy the bike
Love your content keep it up
How’d u get the fender to fit? Did u use larger screws? I have the same forks but the fender doesn't fit at all
nice video man i enjoyed it
Good
I subbed so that I don't lose this parts list! I'm also working on an S/B frameset with 200mm rear clearance for a 19" NBPower QS273 and was thinking real hard about the front end setup... I honestly think this bike is going to be scary
Just changed my front end out to 2023 surron forks that I found for very cheap locally and man are they better then the zoom forks. Definitely would recommend getting a good front end setup.
where did you get the moto seat ?
Not a fan of that charging port location. My clone has it at the top where gas would go in. Nice build dude. How hot does your controller get under full load, full speed and going uphill?
Yes!
I don't have any hills in my area so I can't really tell you how hot it gets under serious load but I am usually going full throttle or sending it on trails and I've had no over heating issues at all.
Thanks for this! And also to all the other commentors!
The issue is the battery.. sorry to be the one to say it but the battery doesnt have enough output off what the controller needs. So try tuning it down or buy a bigger battery
Have you ever fixed that wobbly rear wheel? What caused it?
Also what about cranks
What about the charger link
Where is part twoooo
I've been too lazy to edit it but hopefully tomorrow or Saturday!
Hi have u go link for charger thanks
Why do much just built mine for 2k
What parts you used?
How did you get the front fender to attach ? What the adapter ?
Where you get the axle for the front and back
Could you please tell me what size you bought the special bolts you mentioned in the video, 18mm or 33mm, or which one? Great video, BTW!
measure your bracket spacing
were can I buy a mqcon controller 72v 150 amp 8000 watt controller from ,am in uk
Hey bro where can I get these type of spacers for the kick stand? Or what’s the name of these kind of spacers
Bro do you have to brake in these brakes or something ? 😂 I bought them and tried them out but they aren’t as good ..
I just installed my Sabvcon controller SVMC 7260 but I cannot get my bike to go pass 15m/h (25km/h). Would you know if it is a connection error on my part or perhaps a setting issue?
do you have a contact number? I have the same sthealth Bomber model but I have some questions, could you help me?
hello, i am building a similar bike to yours but i am using 20in bicycle tires. How high is your 19in build? if i buy the front wheel that say on amazon it is a disk break will I be able to put hydraulic breaks on it?
I had a similar issue setting up my controller and motor. The “thumping” is sort of like a misfire. I’m guessing it’s a unstable magnetic field. This also occurs at higher rpm.
Did you manage to find the cause of the issue and fix it?
@@aaron092000 I was told that my aftermarket controller was a sinewave, but in fact it was a square wave. I was dealing with a AliExpress seller.. I was a little bit miffed, but pushed through with the seller until they gave me a discount on a sinewave. No problem since. Another issue I was having was with the throttle /display. The old square waves were frying them or something. I still don’t understand how that happened.
Hi im form poland and i wanted to ask if there is any possibility to deliver the frame to polish? unfortunately, aliexpress ebay and amazon do not deliver to Poland. are any thoughts?
If you can go online you can get the measurements from the advertisement. Then go and ask welders in your country to make the frame
Can some one explain to me what the, "hull test" (idk if that's correct) is?
Hall Test. This is the self learning feature of the Sabvoton. You connect phase and hall wires in any order (but professional will color match them from the motor to controller), then run test, and the controller will pair the motor to itself. After that if the motor runs backwards you just open the app and select “reverse” to make it run correct direction. The Hall phase shift will appear after the test. Not to be confused with commutation angle of 60 or 120.
@@imho7250 that's for the explication, I don't get everything that's mentioned here but i think I'll manage with this explication and some vids of how it works, tryna get my fist DIY ebike working
@@Killer-wu9hk , to make any controller work, it needs battery power connected, the motor phase and hall sensor connectors connected, the throttle connected, and the ignition wire connected. From there you should be able to open the MQCON app and verify voltage settings match your battery. Then with the rear wheel off the ground you would run the hall test, and the motor will start moving slowly as it checks the relationship between the phases and the hall sensors. After it finishes, and you save it, the motor should run. Of the motor runs forward then its correct, if it runs backwards then in the app you can change the direction. You never need to change any phase wires or hall wires after the initial color matching of all 8 wires. Any mismatch will be fixed inside the controller.
@@imho7250 I'm not sure if the controller will connect to the app because, I bought the bike off alibaba from a company called keyu, they seem reputable because they have their own ebike frame and several types of it, the description mentioned a 25a sabvoton controller, my bike 3000w so ima need an upgrade but when I asked about the controller they said 45a keyu controller, I've never heard of a keyu controller, maybe they made a mistake and ment 45a sabvoton or 25a. Also the low showered sabvoton controllers are not Bluetooth compatible, you have to use the computer app, but there's no tutorials about that
@@Killer-wu9hk , if you make a KZread video showing what you have it’s easier to help. There are many controllers. Votol and Kelly need a computer. Sabvoton and Fardriver and YuYangKing use Bluetooth and a phone app.
Top speed??? Awesome build
50MPH
You make very good videos, but you have to post more regularly to grow the channel. I believe in you bro, keep going!
Wtf why would you think it's the controller? 😂 All wheel inside or spokes.
It's the bms lol
It can't be the bms because I run lipos without bms and I have the same issue on one of my bikes. It's a wire combination issue or loose wire maybe.
@@rccrazy what lipo battery's do you have? Alot if not most of the good ones have built in chips for over discharge protection. Though they don't protect against rouge charging.
@aaron092000 most lipos have no form of over discharge protection it's the esc that has the voltage protection parameters and change them with a balance charger. And I use 2 lots of 5 x 9500mah 4s HRB lipos to get 19ah 72v or 20s.
@@rccrazy yeah my bad your right, most don't have discharge protection. Done abit of research and found that some have balance chips inside which could be the case for you 😀 I think maybe like you said, wire combination or phase wires crossing causing unstable magnetic field? Or possibly voltage sag causing the lipo to trip out? I'm curious have you found the solution to this issue? From my experience I was running a 30a bms with 60a peak and when I tried to run over 60a through it, it would do the same thing shown in this video, like a rev limiter on a car. it would only happen once I reached a certain speed too
Good work
Sounds like a gear has cracked in your clutch