I’ve been watching a bunch of your videos. I just bought a AB dinghy and it’s needing some attention, but still very usable in its current condition. I figured I would use it until it finished falling apart and then I would be ready financially to buy another one. Your videos have pretty much convinced me that that’s further down the line than I thought it would be. I’ve got 2 of the 3 chambers holding air, my next project is to change the valve in the third chamber and then to paint the bottom, it’s chipped on more than one rock but I can’t detect anything more than that and then I plan on applying inflatable bottom paint as it spends all of its time in the water and is kinda a hassle cleaning it about every 2 weeks. I’ve figured out where to get the seat holders and how to put new ones on thanks to your videos. There aren’t any tears or big holes, but it needs a paint job. It’s a hard bottom and a new one is ridiculously expensive and if I can get some more years out of this one, all the better. I’m going to sew up a “tent” for it to help keep the rain out… not for camping, but you never really know.
@bobmarleyd591Күн бұрын
If I have a floor that is only coming apart from the tube about 10 inches on one side (not the direct front) would it still be better to peel it all the way off and re-do it all like you did here? Or if the glue isn't to bad elsewhere, could I just fix that one area. Any tips on how to tell? If its coming apart in one area is it safe to assume all the glue is old and shot?
@RongdrikКүн бұрын
Great👍
@TheFishinMortician2 күн бұрын
Awesome! I had some decals made to stick on mine but the writing is much smaller, this gives bigger options and customizations. Thanks for sharing.
@gashopperinc2 күн бұрын
It's my pleasure. Sky's the limit when it comes to painting. Plus they won't curl or peel off like most of them usually do under the sun. Lol.
@frisky1172 күн бұрын
Talking about what you are doing would be better than the music
@LIONKILLER19864 күн бұрын
Is that a long shaft?
@siatosnikolaos60594 күн бұрын
hi may I ask you; what type is it? neoprene or pvc?
@gashopperinc4 күн бұрын
These boats are PVC fabric.
@ashwillmot20515 күн бұрын
Just wondering how bad the tubes would need to be before repair was not an option?
@gashopperinc5 күн бұрын
Good question... well I should be doing a video soon on that exact topic. But a good sign that your tubes are finished is when the skin is badly damaged that you can see the inner threads of the fabric throughout the tops of the tubes.
@duanedasse52567 күн бұрын
I have a Quicksilver model QS330E. I was told to use RH adhesives HH-66 vinyl cement. So I ordered 32 oz of the glue will this work for repairing the Transom?
@gashopperinc6 күн бұрын
No do not use HH66. It's not made for PVC boats and isn't a structural adhesive. I know it's readily available on Amazon, but you'll regret using it.
@NikolaBatinovic-oo2tz7 күн бұрын
BOSTIK SIMSON MSR Construction Adhesive SSKF is a Beast 🤌 I have old neopren boat with micro leaks. This thing saved me time and money ❤
@keithclark9108 күн бұрын
hi..great video..one of the tubes is separated on my 14' mercury zodiac and the other tube is 75% still attached ...the floor is still attached to the transom..do i have to remove the floor boards to repair or can i just deflate and do the job with floor boards still in the boat..reason i find it very difficult to put flloor boards back into the boat and would rather not if i dont have to..hope to hear back soon
@gashopperinc7 күн бұрын
Yes, unfortunately you'll have to remove the floor boards to do that repair. It is an inconvenience, but has to be done to relieve tension on the fabric.
@williamm.361210 күн бұрын
Glad, this confirms what I was doing. Re-Adhering transom to tubes and other parts - do you typically do a dish soap wash down first? I am about to grab demel - and sand down the old glue, and re-apply the two part. Then after cure, going to give the thing a nice scrub down - and add a UV protectant. The one you used on this video, a good application for Ocean environments or..?
@gashopperinc9 күн бұрын
I do normally give the boats a quick wash down to search for leaks and clean out any debris before any repair work is done. Gives less chances of dirt, debris and what nots from finding there way to your working area.
@williamm.36129 күн бұрын
@@gashopperinc i figured the same thing and just finished scrubbing the crud out of entire thing with starbrite. Off topic, do you like to proactively apply a patch to an area where a tear/ deeper cut occured?
@riemerhenstra867810 күн бұрын
heyy great video but i spilled a bit of glue on my boat and now i dont know how to get it off maybe you have a tip thanksss
@gashopperinc7 күн бұрын
MEK or Acetone wiping to soften the glue and my have to sand it away, very lightly till you get to the fabric surface.
@ratdogx411 күн бұрын
I have a 14 ft. novurania ( 1988 model canguro 420 gs / Hypalon) great shape/no uv damage but was stored deflated for 8 yrs. It how has micro leaks on all 3 chambers. Questions: How much should I pour into each tube and how long is the working time? Also how long does it take to cure/fully dry and how long to give it a 2ed coat if needed. Great vids...Thanks, Joe
@gashopperincКүн бұрын
Hey Joe. Generally a 1/3 of the bottle if sufficient. You want to coat the chamber walls so it can fill in those micro leaks. Dry time is usually 24 hours. But if it's puddled in the chamber and hasn't coated the chamber walls, it can stay a liquid for longer periods. Agitation and heat help cure this product quicker. Air and pressure are the activators to start the curing process.
@julianlewis430514 күн бұрын
Nice video....what´s the type of glue you´re using?
@gashopperinc7 күн бұрын
Mainly Zodiac glue, but use others when Zodiac glue is backordered.
@Klako77016 күн бұрын
Bravo
@Klako77016 күн бұрын
Hi my friend I have zodiac FC 470 military boat have about 10 very small holes don’t no why this happened they told me I didn’t wash the boat after I took the boat aout of the water without washing the boat the salt dad the damage don’t no if this tru or not please advise if can be repair thanks
@gashopperinc7 күн бұрын
Anything can be fixed. Salt and UV can have drastic effects on inflatable boats, especially those with PVC fabric. You can always add an additional layer of skin to the affected damaged area. But if the skin is bad, then sometimes it's best to let it go instead of becoming a money pit. Couldn't tell you in your situation as the boat isn't in front of me to make that assessment.
@mejeep10016 күн бұрын
Hey great video, I'm about to remove and rebond my Futura MK1 transom and was wondering how much PVC 2 pack adhesives I need to order? Thanks in advance. Graham
@gashopperinc7 күн бұрын
Depends on thenboat and transom. But would recommend Z7096 Zodiac glue.
@raulrodriguez363816 күн бұрын
What cleaning solution did you use?
@renerioux264416 күн бұрын
Which patch kit and glue do you recommend for an Achilles SD124? I think it is hypalon but I’m not sure. Also, do you have a video on how to remove the wood floor from the boat?
@ukscootinca18 күн бұрын
really informative and you make an enjoyable video, cheers, one question though what glue do you use or recommend ? I have to glue the complete floor to the pontoons on a never used zodiac fh 12.6
@gashopperinc17 күн бұрын
Thank you. I try to be as informative as possible. I recommend using a 2 part glue. Zodiac or Stabond are the preferred choices here, we also work with Weaver when.the others on backorder.
@cangokce675018 күн бұрын
I’ve 2015 ford explorer, I assembled the center console but I couldn’t find anything. Also I checked underneath the driver side seat there is black box module but I’m not sure belongs to headrest DVD.
@txmom122220 күн бұрын
Does anyone know how to adjust the volume on these?
@gashopperinc19 күн бұрын
You'll need an IR universal remote or phone with IR capability and app for universal remote control. Pretty hard to find the replacement remotes for these units.
@txmom122219 күн бұрын
@@gashopperinc That's what I'm learning 😵💫
@kanew.665820 күн бұрын
I have a 1966 model just like this. Not polished but swirled.
@Ryanstuff21 күн бұрын
Why don't patches come pre-sanded?
@FranciscoArabaca-rr5wd23 күн бұрын
thank you gashopper inc.i save lots of repair cost.my highfield 290 is now in top shape.
@halomaniac7424 күн бұрын
Tried going to the website and purchasing the products in this video (which by the way would have been nice to see a list somewhere) tried adding the products and none where in stock. So, tried calling the phone number listed and guess what? The phone number doesn't work.
@gashopperinc24 күн бұрын
Stock is very low on items at the moment. Waiting on restocking order, was late for my orders as I've been dealing with a urgent family emergency. That's strange the number didn't work. Which one did you try toll free or regular number? Toll free only work for Canadian residents for some reason, which I'm trying to get corrected. Other number should work though.
@tylerkreft471025 күн бұрын
Where can I get the glue? Amazon link?
@gashopperinc25 күн бұрын
Not available on Amazon, have to order from a Zodiac Dealer or other inflatable dealer. I would suggest ordering from us, but we're out on PVC glue for the next little bit.
@JOCK53227 күн бұрын
zodiac boats just fall apart had three but will never own another one
@ranchdressing103728 күн бұрын
Pinhole under a Intex Excrusion 5 floor. Tried hh66 tonight.. will super seal work on my boat?
@freshlybaked110 күн бұрын
How did it turn out? Same here
@jdweld4429 күн бұрын
I have the same boat and was wondering how thick the aluminum deck is so I can screw in some tie downs.
@ngoichoi976Ай бұрын
I got a used 35-year-old Achilles 10feet2 boat. I can patch almost all normal punctures. It seems like so many pinhole seams and pinhole leaks that not even worth with the times and materials to fix them. The seam pinhole leaks are the most difficult to patch. Is it possible Super Seal can fix this old boat ? I'm about give this SuperSeal last try before just use the boat with the pump lol. I spend so much money on glues trying to fix all the leaks, but still so many seam and pinhole leak I'm about to give up LOL, the boat can still hold good air for about 1 day.
@gashopperinc29 күн бұрын
It doesn't hurt to try. This stuff has saved customers $$$ in patching. And if you wanted to get a few more years out of the boat, and as long as the leaks aren't to bad, this stuff should coat and seal the inside and give your boat a little extra life.
@ngoichoi97629 күн бұрын
@@gashopperinc ordered 2 bottle and will double or triple coat this stuff on my boat like someone mention in the comment. I already double layer hypalon faric in many parts of the boat try to fix seam leaks and make the boat strong to punctures.
@elmime1Ай бұрын
I have a 2000 zodiac yatchline with console. I need all my valves. I don't know which ones. Please help.
@gashopperincАй бұрын
You can visit our website and see if any of the valves we have e in stock match your boat, or send us pictures to our email and we'll get you in the right direction.
@freshlycutlawnserviceАй бұрын
Need help I have a West Marine PVc boat needs some work lol I tried to patch it and the first patch fald . I was doing a inside patch first when I was sanding the out side to put the second patch on for the put side it started to l;eak I was so pissed lol .. I'm Using HH 66 PVc glue . I feel like I did something wrong .. i sanded it with 80 grit sand paper is that to harsh ? I applied two coats of glue it didn't stick all that great I had to heat it up with the heat gun that seam to get the g;lue sticky again .. I knew right away this patch was going to suck .. Any tips ?? On the glue up ? .. I'm going to go out side soon and see if the second patch held better .. Shouldn't the patch be lilke super sticky and bond right away and not want to peal up .. Any help would be awesome ! Thanks man ! Really enjoy the chanel !! Cheers man !! 🍺 🤙🏽
@gashopperincАй бұрын
Thank you for tuning in!!! I have videos for inner patch repairs already posted, just have to scan through the channel. They have great tips and tricks for you. But from the sounds of it, your prep is good, just wipe with acetone or MEK afterwards, but also throw that can of HH66 in the garbage. It's not made for repairs on inflatable boats, even though lots of folks swear by it. You need a 2 part glue, either by Zodiac, Stabond or Weaver. Those are the highly recommended glues we sell and use here, but running short at the moment on some brands. Use those glues, and you should have no problem with a repair like that.
@timothylindsay3244Ай бұрын
Thanks, very useful step by step. I assume you’ve found the products you use through years of trial and error to work best?
@gashopperincАй бұрын
Yes, lots of trial and error, and hurting joints, lol; but I believe I've found the perfect method. I know there's other ways, but if I find a better way or chemical. I'll be sure to share.
@timothylindsay3244Ай бұрын
@@gashopperinc thanks….you’ve been a big help
@parkcitybradАй бұрын
Kinda worthless. Fast forward mood music montage rather than any real, how-to guidance. Looks like this guy really knows what he’s doing. Would have nice to learn something from him
@gashopperinc29 күн бұрын
Sorry about that, some copyright music in background made KZread put a whole audio track over the parts it was heard. Going to get another video done up without the copyright background music or go into the archives and see if I can redo it.
@parkcitybrad28 күн бұрын
No apologies required. Sounds like you got hosed by KZread. Will keep my eyes open for your video with voiceover guidance. Thanks!
@pilophemperor5723Ай бұрын
These videos are awesome! Just got an old inflatable to repair. What system/tools do you use to inflate the boat?
@gashopperincАй бұрын
We use a compressor and a custom air hose setup we made here. We're planning on building our own setups to sell in the future, just waiting for factory for our templates to see if it can happen.
@ia6980Ай бұрын
Terrible music! Qs pls, if tube is punctured does the mid console sinks?
@gashopperincАй бұрын
If it's a RIB boat, no it will still float even though the tubes are punctured. There's a video on KZread of a gentleman who demonstrates that exact question. If I can find it, I'll post the link here for you.
@jamespasterkiewicz87128 күн бұрын
Nice job we're did you get the tube from, do you repair apex inflatable s , what band is this
@FranciscoArabaca-rr5wdАй бұрын
thanks a lot sir,
@gashopperincАй бұрын
Most welcome
@Dino-11Ай бұрын
Ive got a leaking valve on my right pontoon. The other pontoon is completely fine and i tried swapping the valves but I still have leaks on the right one, When swapping valves the left pontoon showed no leaks. Is the marine grease what I need or is my pontoon bladder ruined somehow? If so what grease did you use here? and does it make a difference? -thanks!
@Dino-11Ай бұрын
I guess my follow up would be. How do I know if the basket is broken? it looooooks fine to me but I dont know what im looking for. would there be a big crack or something?
@gashopperincАй бұрын
We use generic marine grease. One in the video is 3M marine grease. Chances are the basket is broken or there is a stress crack on the fabric around the valve or just under it. To tell if the basket is broken, it won't tighten and will just continuously spin when trying to tighten. Stress cracks, you'll have to pull the valve out and bend around the valve hole and see if there is a cracking. One of my first boats I ever fixed had that problem where we changed the valve, and still leaked. Upon further inspection I noticed the fabric crack. And to repair had to make a donut patch so the valve sealed.
@Dino-11Ай бұрын
@@gashopperinc thanks for the reply. When i tighten it it does get pretty tight but it never really stops, I could try tightening it more but Im afraid Ill over tighten it and break the basket if its not already broken. Is there a way to change the backet? or in that case is the pontoon bladder toast? In the other scenario, when you say fabric crack, my pontoon has a inner bladder and outer canvas. would this crack be on the outer fabric? or the bladder itself? (thank you so much for the help already! Your video was already so helpful, Im very afraid my pontoon is broken) *Update* There is a small tear around the basket housing, but when I spray the bladder with soapy water the bubbles seem to come from in the basket where the threads are. My thoughts is a donut patch would maybe work for ether issue, do you have a recommended product for that? The videos on the channel Im seeing are bigger tears with inner patches, do you have a video on smaller patches like what Im after?
@gashopperincАй бұрын
If the bladder is toast, then you would be filling both chambers from one valve. You'll know when it's tight cause there will be lots of tension. If the tension gets to a point where it all of sudden becomes loose, then the basket is shot. To change the basket, you can do 1 of 2 ways, cut the the valve opening and put a donut patch or find a area of the boat that isn't going to be visible and do a cut there.
@ivanmirchev3115Ай бұрын
I really liked how you gave attention to the aluminium hull. Top work greetings from Germany.
@sailorstuАй бұрын
I was just on your website, and noticed your a Canadian company. So I am wondering if you make the re tube kits here. Roughly how long does it usually take to make up a set? Do they come complete with the oar sockets and everything? Would I have any colour choices when ordering?
@dougbrady6314Ай бұрын
What is the chemical solution you are using for initial cleaning?
@gashopperinc28 күн бұрын
Dawn dish soap is the starting soap we use
@NoWheyHombreАй бұрын
May I ask how grease is getting all in these dinghys or tenders to begin with? Mildew is the only stains my boat ever seems to have.
@gashopperinc28 күн бұрын
I ask myself the same questions all the time.
@sentinel2nodoge201Ай бұрын
Great work. 💪
@gashopperincАй бұрын
Thank you! Cheers!
@johnnychheng6288Ай бұрын
I like and subscribe you cause I like what you doing . I need your brain for this one, I want to double pad the bottom of my tube boat . Where should I got about it .? Not puncture not nothing just want to add support to the bottom .
@gashopperincАй бұрын
There's many different methods of doubling the bottom layers. You can add an additional layer of fabric, you can also add rubstrakes rubber to the bottom, just have to know what fabric your dealing with. EPDM rubber is for Hypalon and PVC is for PVC. And make sure your using the right glue.
@johnnychheng6288Ай бұрын
@@gashopperinc what type of glue ?
@gashopperincАй бұрын
@@johnnychheng6288 Zodiac glue prefer
@johnnychheng6288Ай бұрын
@@gashopperinc thanks
@wyboatman5815Ай бұрын
Hi, may I know what brand of glue are u using????
@gashopperincАй бұрын
Zodiac glue mainly, if not available, Stabond or Weaver. Only the 2 part glue.
@wyboatman5815Ай бұрын
@@gashopperinc Thank you so much 👍🏻👍🏻👍🏻
@alangoodwin7605Ай бұрын
What type of glue or brand are you using
@gashopperincАй бұрын
I mainly use the Zodiac brand for glue repair, but if there is a shortage, I'll use Stabond or Weaver 2 part glues.
@2000redvette1Ай бұрын
thanks for your info on how to do the inside patch. I followed your instructions, Only difference is I used Loctite vinyl, fabric and plastics flexible adhesive. mine was a real job as my cut was near end of pontoon and air inlet, handle and bottom rib were all in the way. We will see, my first patch failed. I used stitch fix, conditions were poor and I was trying to do with pontoon still attached to boat. I brought inside this time and tried to do a better job. My boat is aquos 10.2 boat. A new pontoon will cost me 200.00 so I hope this works. "Thanks for your video.
@chefpeteyАй бұрын
MAY I ASK? What would you think of mounting a SWIVEL SEAT into one of the aluminum floor boards of my CLASSIC MK 1? Feasible?
@gashopperincАй бұрын
I seen it done many time. Either bolt the seats posts to the aluminum floors or use rivnuts and bolt them in.
Пікірлер
I’ve been watching a bunch of your videos. I just bought a AB dinghy and it’s needing some attention, but still very usable in its current condition. I figured I would use it until it finished falling apart and then I would be ready financially to buy another one. Your videos have pretty much convinced me that that’s further down the line than I thought it would be. I’ve got 2 of the 3 chambers holding air, my next project is to change the valve in the third chamber and then to paint the bottom, it’s chipped on more than one rock but I can’t detect anything more than that and then I plan on applying inflatable bottom paint as it spends all of its time in the water and is kinda a hassle cleaning it about every 2 weeks. I’ve figured out where to get the seat holders and how to put new ones on thanks to your videos. There aren’t any tears or big holes, but it needs a paint job. It’s a hard bottom and a new one is ridiculously expensive and if I can get some more years out of this one, all the better. I’m going to sew up a “tent” for it to help keep the rain out… not for camping, but you never really know.
If I have a floor that is only coming apart from the tube about 10 inches on one side (not the direct front) would it still be better to peel it all the way off and re-do it all like you did here? Or if the glue isn't to bad elsewhere, could I just fix that one area. Any tips on how to tell? If its coming apart in one area is it safe to assume all the glue is old and shot?
Great👍
Awesome! I had some decals made to stick on mine but the writing is much smaller, this gives bigger options and customizations. Thanks for sharing.
It's my pleasure. Sky's the limit when it comes to painting. Plus they won't curl or peel off like most of them usually do under the sun. Lol.
Talking about what you are doing would be better than the music
Is that a long shaft?
hi may I ask you; what type is it? neoprene or pvc?
These boats are PVC fabric.
Just wondering how bad the tubes would need to be before repair was not an option?
Good question... well I should be doing a video soon on that exact topic. But a good sign that your tubes are finished is when the skin is badly damaged that you can see the inner threads of the fabric throughout the tops of the tubes.
I have a Quicksilver model QS330E. I was told to use RH adhesives HH-66 vinyl cement. So I ordered 32 oz of the glue will this work for repairing the Transom?
No do not use HH66. It's not made for PVC boats and isn't a structural adhesive. I know it's readily available on Amazon, but you'll regret using it.
BOSTIK SIMSON MSR Construction Adhesive SSKF is a Beast 🤌 I have old neopren boat with micro leaks. This thing saved me time and money ❤
hi..great video..one of the tubes is separated on my 14' mercury zodiac and the other tube is 75% still attached ...the floor is still attached to the transom..do i have to remove the floor boards to repair or can i just deflate and do the job with floor boards still in the boat..reason i find it very difficult to put flloor boards back into the boat and would rather not if i dont have to..hope to hear back soon
Yes, unfortunately you'll have to remove the floor boards to do that repair. It is an inconvenience, but has to be done to relieve tension on the fabric.
Glad, this confirms what I was doing. Re-Adhering transom to tubes and other parts - do you typically do a dish soap wash down first? I am about to grab demel - and sand down the old glue, and re-apply the two part. Then after cure, going to give the thing a nice scrub down - and add a UV protectant. The one you used on this video, a good application for Ocean environments or..?
I do normally give the boats a quick wash down to search for leaks and clean out any debris before any repair work is done. Gives less chances of dirt, debris and what nots from finding there way to your working area.
@@gashopperinc i figured the same thing and just finished scrubbing the crud out of entire thing with starbrite. Off topic, do you like to proactively apply a patch to an area where a tear/ deeper cut occured?
heyy great video but i spilled a bit of glue on my boat and now i dont know how to get it off maybe you have a tip thanksss
MEK or Acetone wiping to soften the glue and my have to sand it away, very lightly till you get to the fabric surface.
I have a 14 ft. novurania ( 1988 model canguro 420 gs / Hypalon) great shape/no uv damage but was stored deflated for 8 yrs. It how has micro leaks on all 3 chambers. Questions: How much should I pour into each tube and how long is the working time? Also how long does it take to cure/fully dry and how long to give it a 2ed coat if needed. Great vids...Thanks, Joe
Hey Joe. Generally a 1/3 of the bottle if sufficient. You want to coat the chamber walls so it can fill in those micro leaks. Dry time is usually 24 hours. But if it's puddled in the chamber and hasn't coated the chamber walls, it can stay a liquid for longer periods. Agitation and heat help cure this product quicker. Air and pressure are the activators to start the curing process.
Nice video....what´s the type of glue you´re using?
Mainly Zodiac glue, but use others when Zodiac glue is backordered.
Bravo
Hi my friend I have zodiac FC 470 military boat have about 10 very small holes don’t no why this happened they told me I didn’t wash the boat after I took the boat aout of the water without washing the boat the salt dad the damage don’t no if this tru or not please advise if can be repair thanks
Anything can be fixed. Salt and UV can have drastic effects on inflatable boats, especially those with PVC fabric. You can always add an additional layer of skin to the affected damaged area. But if the skin is bad, then sometimes it's best to let it go instead of becoming a money pit. Couldn't tell you in your situation as the boat isn't in front of me to make that assessment.
Hey great video, I'm about to remove and rebond my Futura MK1 transom and was wondering how much PVC 2 pack adhesives I need to order? Thanks in advance. Graham
Depends on thenboat and transom. But would recommend Z7096 Zodiac glue.
What cleaning solution did you use?
Which patch kit and glue do you recommend for an Achilles SD124? I think it is hypalon but I’m not sure. Also, do you have a video on how to remove the wood floor from the boat?
really informative and you make an enjoyable video, cheers, one question though what glue do you use or recommend ? I have to glue the complete floor to the pontoons on a never used zodiac fh 12.6
Thank you. I try to be as informative as possible. I recommend using a 2 part glue. Zodiac or Stabond are the preferred choices here, we also work with Weaver when.the others on backorder.
I’ve 2015 ford explorer, I assembled the center console but I couldn’t find anything. Also I checked underneath the driver side seat there is black box module but I’m not sure belongs to headrest DVD.
Does anyone know how to adjust the volume on these?
You'll need an IR universal remote or phone with IR capability and app for universal remote control. Pretty hard to find the replacement remotes for these units.
@@gashopperinc That's what I'm learning 😵💫
I have a 1966 model just like this. Not polished but swirled.
Why don't patches come pre-sanded?
thank you gashopper inc.i save lots of repair cost.my highfield 290 is now in top shape.
Tried going to the website and purchasing the products in this video (which by the way would have been nice to see a list somewhere) tried adding the products and none where in stock. So, tried calling the phone number listed and guess what? The phone number doesn't work.
Stock is very low on items at the moment. Waiting on restocking order, was late for my orders as I've been dealing with a urgent family emergency. That's strange the number didn't work. Which one did you try toll free or regular number? Toll free only work for Canadian residents for some reason, which I'm trying to get corrected. Other number should work though.
Where can I get the glue? Amazon link?
Not available on Amazon, have to order from a Zodiac Dealer or other inflatable dealer. I would suggest ordering from us, but we're out on PVC glue for the next little bit.
zodiac boats just fall apart had three but will never own another one
Pinhole under a Intex Excrusion 5 floor. Tried hh66 tonight.. will super seal work on my boat?
How did it turn out? Same here
I have the same boat and was wondering how thick the aluminum deck is so I can screw in some tie downs.
I got a used 35-year-old Achilles 10feet2 boat. I can patch almost all normal punctures. It seems like so many pinhole seams and pinhole leaks that not even worth with the times and materials to fix them. The seam pinhole leaks are the most difficult to patch. Is it possible Super Seal can fix this old boat ? I'm about give this SuperSeal last try before just use the boat with the pump lol. I spend so much money on glues trying to fix all the leaks, but still so many seam and pinhole leak I'm about to give up LOL, the boat can still hold good air for about 1 day.
It doesn't hurt to try. This stuff has saved customers $$$ in patching. And if you wanted to get a few more years out of the boat, and as long as the leaks aren't to bad, this stuff should coat and seal the inside and give your boat a little extra life.
@@gashopperinc ordered 2 bottle and will double or triple coat this stuff on my boat like someone mention in the comment. I already double layer hypalon faric in many parts of the boat try to fix seam leaks and make the boat strong to punctures.
I have a 2000 zodiac yatchline with console. I need all my valves. I don't know which ones. Please help.
You can visit our website and see if any of the valves we have e in stock match your boat, or send us pictures to our email and we'll get you in the right direction.
Need help I have a West Marine PVc boat needs some work lol I tried to patch it and the first patch fald . I was doing a inside patch first when I was sanding the out side to put the second patch on for the put side it started to l;eak I was so pissed lol .. I'm Using HH 66 PVc glue . I feel like I did something wrong .. i sanded it with 80 grit sand paper is that to harsh ? I applied two coats of glue it didn't stick all that great I had to heat it up with the heat gun that seam to get the g;lue sticky again .. I knew right away this patch was going to suck .. Any tips ?? On the glue up ? .. I'm going to go out side soon and see if the second patch held better .. Shouldn't the patch be lilke super sticky and bond right away and not want to peal up .. Any help would be awesome ! Thanks man ! Really enjoy the chanel !! Cheers man !! 🍺 🤙🏽
Thank you for tuning in!!! I have videos for inner patch repairs already posted, just have to scan through the channel. They have great tips and tricks for you. But from the sounds of it, your prep is good, just wipe with acetone or MEK afterwards, but also throw that can of HH66 in the garbage. It's not made for repairs on inflatable boats, even though lots of folks swear by it. You need a 2 part glue, either by Zodiac, Stabond or Weaver. Those are the highly recommended glues we sell and use here, but running short at the moment on some brands. Use those glues, and you should have no problem with a repair like that.
Thanks, very useful step by step. I assume you’ve found the products you use through years of trial and error to work best?
Yes, lots of trial and error, and hurting joints, lol; but I believe I've found the perfect method. I know there's other ways, but if I find a better way or chemical. I'll be sure to share.
@@gashopperinc thanks….you’ve been a big help
Kinda worthless. Fast forward mood music montage rather than any real, how-to guidance. Looks like this guy really knows what he’s doing. Would have nice to learn something from him
Sorry about that, some copyright music in background made KZread put a whole audio track over the parts it was heard. Going to get another video done up without the copyright background music or go into the archives and see if I can redo it.
No apologies required. Sounds like you got hosed by KZread. Will keep my eyes open for your video with voiceover guidance. Thanks!
These videos are awesome! Just got an old inflatable to repair. What system/tools do you use to inflate the boat?
We use a compressor and a custom air hose setup we made here. We're planning on building our own setups to sell in the future, just waiting for factory for our templates to see if it can happen.
Terrible music! Qs pls, if tube is punctured does the mid console sinks?
If it's a RIB boat, no it will still float even though the tubes are punctured. There's a video on KZread of a gentleman who demonstrates that exact question. If I can find it, I'll post the link here for you.
Nice job we're did you get the tube from, do you repair apex inflatable s , what band is this
thanks a lot sir,
Most welcome
Ive got a leaking valve on my right pontoon. The other pontoon is completely fine and i tried swapping the valves but I still have leaks on the right one, When swapping valves the left pontoon showed no leaks. Is the marine grease what I need or is my pontoon bladder ruined somehow? If so what grease did you use here? and does it make a difference? -thanks!
I guess my follow up would be. How do I know if the basket is broken? it looooooks fine to me but I dont know what im looking for. would there be a big crack or something?
We use generic marine grease. One in the video is 3M marine grease. Chances are the basket is broken or there is a stress crack on the fabric around the valve or just under it. To tell if the basket is broken, it won't tighten and will just continuously spin when trying to tighten. Stress cracks, you'll have to pull the valve out and bend around the valve hole and see if there is a cracking. One of my first boats I ever fixed had that problem where we changed the valve, and still leaked. Upon further inspection I noticed the fabric crack. And to repair had to make a donut patch so the valve sealed.
@@gashopperinc thanks for the reply. When i tighten it it does get pretty tight but it never really stops, I could try tightening it more but Im afraid Ill over tighten it and break the basket if its not already broken. Is there a way to change the backet? or in that case is the pontoon bladder toast? In the other scenario, when you say fabric crack, my pontoon has a inner bladder and outer canvas. would this crack be on the outer fabric? or the bladder itself? (thank you so much for the help already! Your video was already so helpful, Im very afraid my pontoon is broken) *Update* There is a small tear around the basket housing, but when I spray the bladder with soapy water the bubbles seem to come from in the basket where the threads are. My thoughts is a donut patch would maybe work for ether issue, do you have a recommended product for that? The videos on the channel Im seeing are bigger tears with inner patches, do you have a video on smaller patches like what Im after?
If the bladder is toast, then you would be filling both chambers from one valve. You'll know when it's tight cause there will be lots of tension. If the tension gets to a point where it all of sudden becomes loose, then the basket is shot. To change the basket, you can do 1 of 2 ways, cut the the valve opening and put a donut patch or find a area of the boat that isn't going to be visible and do a cut there.
I really liked how you gave attention to the aluminium hull. Top work greetings from Germany.
I was just on your website, and noticed your a Canadian company. So I am wondering if you make the re tube kits here. Roughly how long does it usually take to make up a set? Do they come complete with the oar sockets and everything? Would I have any colour choices when ordering?
What is the chemical solution you are using for initial cleaning?
Dawn dish soap is the starting soap we use
May I ask how grease is getting all in these dinghys or tenders to begin with? Mildew is the only stains my boat ever seems to have.
I ask myself the same questions all the time.
Great work. 💪
Thank you! Cheers!
I like and subscribe you cause I like what you doing . I need your brain for this one, I want to double pad the bottom of my tube boat . Where should I got about it .? Not puncture not nothing just want to add support to the bottom .
There's many different methods of doubling the bottom layers. You can add an additional layer of fabric, you can also add rubstrakes rubber to the bottom, just have to know what fabric your dealing with. EPDM rubber is for Hypalon and PVC is for PVC. And make sure your using the right glue.
@@gashopperinc what type of glue ?
@@johnnychheng6288 Zodiac glue prefer
@@gashopperinc thanks
Hi, may I know what brand of glue are u using????
Zodiac glue mainly, if not available, Stabond or Weaver. Only the 2 part glue.
@@gashopperinc Thank you so much 👍🏻👍🏻👍🏻
What type of glue or brand are you using
I mainly use the Zodiac brand for glue repair, but if there is a shortage, I'll use Stabond or Weaver 2 part glues.
thanks for your info on how to do the inside patch. I followed your instructions, Only difference is I used Loctite vinyl, fabric and plastics flexible adhesive. mine was a real job as my cut was near end of pontoon and air inlet, handle and bottom rib were all in the way. We will see, my first patch failed. I used stitch fix, conditions were poor and I was trying to do with pontoon still attached to boat. I brought inside this time and tried to do a better job. My boat is aquos 10.2 boat. A new pontoon will cost me 200.00 so I hope this works. "Thanks for your video.
MAY I ASK? What would you think of mounting a SWIVEL SEAT into one of the aluminum floor boards of my CLASSIC MK 1? Feasible?
I seen it done many time. Either bolt the seats posts to the aluminum floors or use rivnuts and bolt them in.