Fryette Amplification is a manufacturer of all tube, high end guitar amplifiers, speakers and accessories. Hand built by rockers in the USA since 1989! Sales: [email protected] Technical Support: [email protected]
What was the brand of that blue cap? Many companies use that blue color. Even F&T has dual can caps in that color. But I can't believe that F&T would die in 5 years. I use them in most of my amplifiers and I haven't seen any issues yet. They measure at or above the given value. ESR is always good. Though last batch of 50 + 50 500V I got sections are more apart then before. One side has higher capacitance and better ESR than the other. Still way in the tolerance and at positive side. But old batch was having more alike values. One cap would be better than others in the old batch but they were all above stated values. 32 + 32 were very similar between sections and between each other. Their single caps were even more consistent for me.
@NINEWALKING13 сағат бұрын
Few years ago there was a Marshall PA head for reasonable price in the music store in the other city. It looked very similar to that one. I was like score, if it has proper irons it’s a gold. Plus so many channels that must mean lot of preamp tubes and other goodies. Then I saw inside pictures and that was it. Disaster. Plus no way near what I thought it will be. Way less parts and modified and worked on. Looked very sad and I just decided not to get it. Something cheaper than it should be is often just almost junk. It’s nice t easy to get those good deals.
@timeagan89319 сағат бұрын
Is it "Amp-->Two Notes"OPUS"-->Loadbox-->Speaker OR...............................Is it "Amp-->Loadbox-->OPUS-->Speaker? And finally what jacks use (speaker cable)?? Thank you so much for your help in advance because I am "dead in the water" ntil i know the safe way to cable this
@FryetteAmps16 сағат бұрын
First way may be better but either way is OK. Speaker cables on AMP IN and SPKR OUT. fryette.com/content/Power_Station_PS2A_Manual.pdf
@deadgypsy6780Күн бұрын
Dude you crushed it
@theRodofwarКүн бұрын
Great Video !!!!!!!!!!!!!!!!!!!!! Joe. I have a question. ON the FRYETTE website you sell COLOR CODED speaker cables for the POWER STATION. are these standard speaker cables or necessary for the use of the PS-100 ???????? THX !!!!!!!!!!!!!!!
@FryetteAmpsКүн бұрын
Standard speaker cables are usually 18ga. "Heavy Duty" cables are usually 16ga. Our cables are 14ga for maximum power handling capacity from the amp to the Power Station, and maximum fidelity from the Power Station to your cab.
@theRodofwarКүн бұрын
@@FryetteAmps AH !!!!! Thank You for the INFO and Thank You for the fast response !!!!!!!!!!!!!!!!
@tranquilitybase64172 күн бұрын
How about running a GPDI through a Power Station? Can we hear that?
@greg93452 күн бұрын
Not good enough Mr Fryette your amps all seem to have little gremlins and problems straight out of the box. Where's the QC on your amps mate ? You don't have these problems with Marshall or others yet your amps have problems new from the shop ???? Overrated product and Overpriced not impressed at all, since buying a NEW 2/90/2 nothing but problems. My old Marshall mono block is still kicking arse after 25yrs.
@SeventhStringHeaven3 күн бұрын
The best I've heard you sound Joe. The tone and playing and song writing. Great stuff.
@donmcdonald48743 күн бұрын
Whoa!! You killed it!! 🎉. That was the most tight and awesome demo video I’ve ever seen!!! Much love!! ❤
@bjhale5423 күн бұрын
awesome Joe! Sounds incredible.
@shredevil_133 күн бұрын
I just bought a PS-100 after watching your demos. Now I’m seriously considering the Deliverance head.😅
@DustinWilbourn3 күн бұрын
Dang Joe, you absolutely snapped on this song!! That main wammy bar lick is still stuck in my head a day later. 🤘🤘
@ariskoskinas4 күн бұрын
Does the effects loop,goes through the xlr or unbalanced output to have your effects in recording in ps100 ?
@FryetteAmps4 күн бұрын
Signal path is Amp In > Line Out > Line In > FX Loop > Power Amp > Speaker Out. If you want effects direct to DAW, use Line Out > external effects > DAW, or FX Send > external effects > DAW.
@samcraig5054 күн бұрын
Right on Joe!
@BenBreard4 күн бұрын
SOB! That sounds great. Killer playing. Great work.
@johngraves21854 күн бұрын
That sounds awesome! Nice work! Cheers!
@lbrondel4 күн бұрын
Great tune, playing and tones!
@lousekoya18034 күн бұрын
Absolutely wOW From Stevie Ray's low ends to MOnster crunch to beautiful lead tones , well done ! And your playing is superb !
@Echoplexi.4 күн бұрын
Where did you get that little rack case for the PS-100? Demo sounds great!
@FryetteAmps4 күн бұрын
It's the new Rack HeadCase. It'll be up on our webstore next week and available from dealers in a week or two as well.
@Echoplexi.4 күн бұрын
@@FryetteAmps cool!
@maxwellblakely79524 күн бұрын
@@FryetteAmps thats bad ass, ill buy one
@JohnO-yd3te4 күн бұрын
Great playing and tone. Well done!
@barrymurphy55484 күн бұрын
Incredible tones, incredible playing !!
@theRodofwar4 күн бұрын
GREAT VIDEO !!!!!!!!!!!!!!!!!!! Every note sounds so clear !!!!!!!!!!!!!!!!!!!!!!! WOW !!!!!!!!!!!!!!!!!!!
@FryetteAmps4 күн бұрын
It's the new Rack HeadCase. It'll be up on our webstore next week and available from dealers in a week or two as well.
@Lu_Woods4 күн бұрын
Love the single setting approach. Thx Joe, sounds thick and pointy ; )
@boyfarrell4 күн бұрын
Great playing and tones, I’m super inspired to pick up my guitar and plug in. 👍🏻
@YMESYDT4 күн бұрын
That’s the best demo I’ve heard thusfar
@JR_Taylor4 күн бұрын
You undersell your playing, love it
@flaviocatalanoguitar4 күн бұрын
That sound GREAT!
@alexc26807 күн бұрын
Love the playing!
@Snoopdave20009 күн бұрын
Can I survive with a ps2 and not be able to switch effects loop on & off?
@FryetteAmps9 күн бұрын
Usually if you're going to the effort of hooking up an effect, such as a delay or reverb, you're not that likely to turn it off.
@christinemocadlo7699 күн бұрын
Awessome Video !! Killer Hamer too!!!!
@timeagan89312 күн бұрын
To FRYETTE: I have a PS100(which I love) HOWEVER:: I was wondering If the cyclops in ANY way solves the problem of Not being able to hear the Effects in the effects loop in the outgoing "line out" (either balanced or unbalanced) that goes to the DAW. You stated that the "effects loop" is AFTER the "line out" Thereby nullifying any effects in the loop. So the only way I can see around this is: Going from the "Balanced line out into the input of the effects chain...then from the effects chain out, into the DAW...Is that about it???
@FryetteAmps12 күн бұрын
The Power Station Line Out is a line level copy of your amps output connected to a load. That is what you would normally send to an interface or DAW and add your effects within the DAW. The FX Loop takes that Line Out level and sends it to external effects, then returns them to be sent to the power amp stage in the Power Station so you will hear the effects in the speakers. So what you're asking for is TWO Line Outs. The one that's already there serving its intended purpose, and then another one that feeds off of the Power Station Speaker Output that you can use to send the total effected signal to wherever else you intend to connect that. Since there is no room on the rear panel to add another line out, you should consider getting an external line out level box for the second function. Or, simply send from the loop to pedals and the output of pedals to your recording interface or DAW for example.
@timeagan89312 күн бұрын
To FRYETTE: I have a PS100(which I love) HOWEVER:: I was wondering If the cyclops in ANY way solves the problem of Not being able to hear the Effects in the effects loop in the outgoing "line out" (either balanced or unbalanced) that goes to the DAW. You stated that the "effects loop" is AFTER the "line out" Thereby nullifying any effects in the loop. So the only way I can see around this is: Going from the "Balanced line out into the input of the effects chain...then from the effects chain out, into the DAW...Is that about it???
@IrakliySherozia13 күн бұрын
thank you for this video so much!!!
@tetsuo219514 күн бұрын
I'll never understand techs who are hesitant to replace 40 year old electrolytic caps. Just replace it and be good another 40 years.
@FryetteAmps13 күн бұрын
We'll never understand why people insist on paying for, or charging others for an operation that we've proven repeatedly is not always necessary, or even recommended in many cases. But sure, please tell us how many times you will do or pay for this operation again using the same logic over the next 40 years.
@tetsuo219511 күн бұрын
@@FryetteAmps I'd rather spend $50 on caps that I know will last 40 years than wait until they fail and I've got bigger problems. Just me. I think you might be part of the minority in this thinking.
@FryetteAmps10 күн бұрын
@@tetsuo2195 We are definitely in the minority. We'd rather leave tested, well performing 40 year old capacitors in a perfectly functioning amplifier than charge the customer $200 (because that is what it would really cost them) to replace them with current parts that in many cases likely would not last even 10 years. Understanding how this dynamic works in the real world is essential and often misunderstood, which is the point of this video. The facts, supported by scientifically derived evidence beats personal bias and internet hearsay every time.
@tetsuo219510 күн бұрын
@@FryetteAmps I was speaking as someone who can work on amps, so $50 in parts, to me, is worth the peace of mind, . There is no harm in replacing 40 year old filter caps. You can find science that says you might not die from smoking a a cigarette today. But why not eliminate the risk and just quit now? Those old caps might test ok and work, but why chance it to save a few bucks? I don't see any benefit to keeping old filter caps. But, to each their own.
@FryetteAmps10 күн бұрын
@@tetsuo2195 Working on your own amps puts you in the minority (welcome!) and only confers limited expertise on the subject of component design, failure statistics and the ability to save money on your own repairs. But using tour own logic, why not “eliminate the risk” entirely and replace all of those pesky pots, resistors and especially those 40 year old broken down transformers? If you want to head off any possible disaster, don’t just do a half-asses job. Put your money where your mouth is!
@johnsmith-ug5tp17 күн бұрын
Thanks to the creator for breaking this down with no tacky up selling.
@rck196919 күн бұрын
Ok thanks , so you ran your amp into the power station but didnt need to hook the power station up to a cab ? So you can use the power station as a load box and not need a cab ? Sorry i just ordered one and i didnt know that could be done i thought it had to be hooked to cab and use as an attenuator only . Am i correct that you can use it as load with no cab or am i missing somthing ? Either way great piece of gear steve is a genius! Thank you for any help
@FryetteAmps19 күн бұрын
Correct. You can use it as a standalone load only. If you're really cranking your amp, it's a good idea to turn the PS power switch on so the fan operates. See "Silent Mode" in the manual. fryette.com/content/Power_Station_PS2A_Manual.pdf
@eoinc409120 күн бұрын
Sounds analogous to buying a new guitar, changing the tuners and strings and not turning the guitar when finished! 😩. Hope you follow this up with a video explaining how to bias a Friedman Plex 🤞❤️
@shanewoodman20 күн бұрын
Joe's been itching to play the Sig:X for some time from what I recall. Would love to see you guys fire it up on the show and A/B it the Deliverance or Pittbull!
@SteveSanchez021 күн бұрын
Goddamn Steve, badass playing man! You make your Strat sound killer !
@Rolly-yg8yt21 күн бұрын
"my D is pretty low"
@tomrollison549622 күн бұрын
Love
@djpgreek23 күн бұрын
1. is there a way to connect 2 tube preamps and switch between those versus a preamp and an actual amp head? 2. Can I use just one preamp with cyclops? I’m contemplating buying it so I can go into the line in of the power station and free up the effect loop since I’ve been going into the effects return of the PS2A direct from preamp.
@FryetteAmps22 күн бұрын
1) Yes. Easily. 2) Yes, that's fine too.
@djpgreek22 күн бұрын
@@FryetteAmps can you explain how to wire up the two preamps?
@adamwatson691623 күн бұрын
The PRS So called Hendrix amp sounds very unimpressive to my ears.
@realtruenorth27 күн бұрын
Fryette amps are the GOAT. No apologies. Play one if you get a chance.
@asnark711527 күн бұрын
Is the headphone amp in the unit analog or digital? Thanks,...
@FryetteAmps26 күн бұрын
The audio signal path is all analog up to and after the IR cab cab generator.
@Robstafarian28 күн бұрын
As far as I am concerned, a smaller and lighter Deliverance is a Deliverance Synergy module in the Synergy SYN-30 head or the forthcoming SYN-20 head. Personally, I would rather run a SYN-1 chassis into a Fryette Power Station.
@choppertownusa459729 күн бұрын
Will bad power tubes result in no volume in operate mode
@FryetteAmps28 күн бұрын
That could be the issue. For more info, please contact [email protected]
@jimcastillo8950Ай бұрын
Hello, when installing new pre amp tubes, what brand are you using these days....... I like your Hamer Guitar.............
@FryetteAmps29 күн бұрын
We’ve used Shuguang a lot in the past. Now that they are available again, we’ll be using them where applicable. We also use JJ, Psvane and in some models, a Tung-Sol in V1.
@Stark4MachinesАй бұрын
I love the smell of hot tubes in the morning. In all seriousness, tube amps excite more of my human senses than just hearing. After playing a Pitbull, I found a top 3 most enjoyable life experience. Fryette Bass Guitar division when? 😂
@DevilsAdvocateDAАй бұрын
Here is what is Bad Ass about this video folks... He Is Hot Switching The Speaker Output Between His Speaker and Load! And No Smoke Was Released In This Video...Damn Those Circuit Boards Are Sexy!
Пікірлер
What was the brand of that blue cap? Many companies use that blue color. Even F&T has dual can caps in that color. But I can't believe that F&T would die in 5 years. I use them in most of my amplifiers and I haven't seen any issues yet. They measure at or above the given value. ESR is always good. Though last batch of 50 + 50 500V I got sections are more apart then before. One side has higher capacitance and better ESR than the other. Still way in the tolerance and at positive side. But old batch was having more alike values. One cap would be better than others in the old batch but they were all above stated values. 32 + 32 were very similar between sections and between each other. Their single caps were even more consistent for me.
Few years ago there was a Marshall PA head for reasonable price in the music store in the other city. It looked very similar to that one. I was like score, if it has proper irons it’s a gold. Plus so many channels that must mean lot of preamp tubes and other goodies. Then I saw inside pictures and that was it. Disaster. Plus no way near what I thought it will be. Way less parts and modified and worked on. Looked very sad and I just decided not to get it. Something cheaper than it should be is often just almost junk. It’s nice t easy to get those good deals.
Is it "Amp-->Two Notes"OPUS"-->Loadbox-->Speaker OR...............................Is it "Amp-->Loadbox-->OPUS-->Speaker? And finally what jacks use (speaker cable)?? Thank you so much for your help in advance because I am "dead in the water" ntil i know the safe way to cable this
First way may be better but either way is OK. Speaker cables on AMP IN and SPKR OUT. fryette.com/content/Power_Station_PS2A_Manual.pdf
Dude you crushed it
Great Video !!!!!!!!!!!!!!!!!!!!! Joe. I have a question. ON the FRYETTE website you sell COLOR CODED speaker cables for the POWER STATION. are these standard speaker cables or necessary for the use of the PS-100 ???????? THX !!!!!!!!!!!!!!!
Standard speaker cables are usually 18ga. "Heavy Duty" cables are usually 16ga. Our cables are 14ga for maximum power handling capacity from the amp to the Power Station, and maximum fidelity from the Power Station to your cab.
@@FryetteAmps AH !!!!! Thank You for the INFO and Thank You for the fast response !!!!!!!!!!!!!!!!
How about running a GPDI through a Power Station? Can we hear that?
Not good enough Mr Fryette your amps all seem to have little gremlins and problems straight out of the box. Where's the QC on your amps mate ? You don't have these problems with Marshall or others yet your amps have problems new from the shop ???? Overrated product and Overpriced not impressed at all, since buying a NEW 2/90/2 nothing but problems. My old Marshall mono block is still kicking arse after 25yrs.
The best I've heard you sound Joe. The tone and playing and song writing. Great stuff.
Whoa!! You killed it!! 🎉. That was the most tight and awesome demo video I’ve ever seen!!! Much love!! ❤
awesome Joe! Sounds incredible.
I just bought a PS-100 after watching your demos. Now I’m seriously considering the Deliverance head.😅
Dang Joe, you absolutely snapped on this song!! That main wammy bar lick is still stuck in my head a day later. 🤘🤘
Does the effects loop,goes through the xlr or unbalanced output to have your effects in recording in ps100 ?
Signal path is Amp In > Line Out > Line In > FX Loop > Power Amp > Speaker Out. If you want effects direct to DAW, use Line Out > external effects > DAW, or FX Send > external effects > DAW.
Right on Joe!
SOB! That sounds great. Killer playing. Great work.
That sounds awesome! Nice work! Cheers!
Great tune, playing and tones!
Absolutely wOW From Stevie Ray's low ends to MOnster crunch to beautiful lead tones , well done ! And your playing is superb !
Where did you get that little rack case for the PS-100? Demo sounds great!
It's the new Rack HeadCase. It'll be up on our webstore next week and available from dealers in a week or two as well.
@@FryetteAmps cool!
@@FryetteAmps thats bad ass, ill buy one
Great playing and tone. Well done!
Incredible tones, incredible playing !!
GREAT VIDEO !!!!!!!!!!!!!!!!!!! Every note sounds so clear !!!!!!!!!!!!!!!!!!!!!!! WOW !!!!!!!!!!!!!!!!!!!
It's the new Rack HeadCase. It'll be up on our webstore next week and available from dealers in a week or two as well.
Love the single setting approach. Thx Joe, sounds thick and pointy ; )
Great playing and tones, I’m super inspired to pick up my guitar and plug in. 👍🏻
That’s the best demo I’ve heard thusfar
You undersell your playing, love it
That sound GREAT!
Love the playing!
Can I survive with a ps2 and not be able to switch effects loop on & off?
Usually if you're going to the effort of hooking up an effect, such as a delay or reverb, you're not that likely to turn it off.
Awessome Video !! Killer Hamer too!!!!
To FRYETTE: I have a PS100(which I love) HOWEVER:: I was wondering If the cyclops in ANY way solves the problem of Not being able to hear the Effects in the effects loop in the outgoing "line out" (either balanced or unbalanced) that goes to the DAW. You stated that the "effects loop" is AFTER the "line out" Thereby nullifying any effects in the loop. So the only way I can see around this is: Going from the "Balanced line out into the input of the effects chain...then from the effects chain out, into the DAW...Is that about it???
The Power Station Line Out is a line level copy of your amps output connected to a load. That is what you would normally send to an interface or DAW and add your effects within the DAW. The FX Loop takes that Line Out level and sends it to external effects, then returns them to be sent to the power amp stage in the Power Station so you will hear the effects in the speakers. So what you're asking for is TWO Line Outs. The one that's already there serving its intended purpose, and then another one that feeds off of the Power Station Speaker Output that you can use to send the total effected signal to wherever else you intend to connect that. Since there is no room on the rear panel to add another line out, you should consider getting an external line out level box for the second function. Or, simply send from the loop to pedals and the output of pedals to your recording interface or DAW for example.
To FRYETTE: I have a PS100(which I love) HOWEVER:: I was wondering If the cyclops in ANY way solves the problem of Not being able to hear the Effects in the effects loop in the outgoing "line out" (either balanced or unbalanced) that goes to the DAW. You stated that the "effects loop" is AFTER the "line out" Thereby nullifying any effects in the loop. So the only way I can see around this is: Going from the "Balanced line out into the input of the effects chain...then from the effects chain out, into the DAW...Is that about it???
thank you for this video so much!!!
I'll never understand techs who are hesitant to replace 40 year old electrolytic caps. Just replace it and be good another 40 years.
We'll never understand why people insist on paying for, or charging others for an operation that we've proven repeatedly is not always necessary, or even recommended in many cases. But sure, please tell us how many times you will do or pay for this operation again using the same logic over the next 40 years.
@@FryetteAmps I'd rather spend $50 on caps that I know will last 40 years than wait until they fail and I've got bigger problems. Just me. I think you might be part of the minority in this thinking.
@@tetsuo2195 We are definitely in the minority. We'd rather leave tested, well performing 40 year old capacitors in a perfectly functioning amplifier than charge the customer $200 (because that is what it would really cost them) to replace them with current parts that in many cases likely would not last even 10 years. Understanding how this dynamic works in the real world is essential and often misunderstood, which is the point of this video. The facts, supported by scientifically derived evidence beats personal bias and internet hearsay every time.
@@FryetteAmps I was speaking as someone who can work on amps, so $50 in parts, to me, is worth the peace of mind, . There is no harm in replacing 40 year old filter caps. You can find science that says you might not die from smoking a a cigarette today. But why not eliminate the risk and just quit now? Those old caps might test ok and work, but why chance it to save a few bucks? I don't see any benefit to keeping old filter caps. But, to each their own.
@@tetsuo2195 Working on your own amps puts you in the minority (welcome!) and only confers limited expertise on the subject of component design, failure statistics and the ability to save money on your own repairs. But using tour own logic, why not “eliminate the risk” entirely and replace all of those pesky pots, resistors and especially those 40 year old broken down transformers? If you want to head off any possible disaster, don’t just do a half-asses job. Put your money where your mouth is!
Thanks to the creator for breaking this down with no tacky up selling.
Ok thanks , so you ran your amp into the power station but didnt need to hook the power station up to a cab ? So you can use the power station as a load box and not need a cab ? Sorry i just ordered one and i didnt know that could be done i thought it had to be hooked to cab and use as an attenuator only . Am i correct that you can use it as load with no cab or am i missing somthing ? Either way great piece of gear steve is a genius! Thank you for any help
Correct. You can use it as a standalone load only. If you're really cranking your amp, it's a good idea to turn the PS power switch on so the fan operates. See "Silent Mode" in the manual. fryette.com/content/Power_Station_PS2A_Manual.pdf
Sounds analogous to buying a new guitar, changing the tuners and strings and not turning the guitar when finished! 😩. Hope you follow this up with a video explaining how to bias a Friedman Plex 🤞❤️
Joe's been itching to play the Sig:X for some time from what I recall. Would love to see you guys fire it up on the show and A/B it the Deliverance or Pittbull!
Goddamn Steve, badass playing man! You make your Strat sound killer !
"my D is pretty low"
Love
1. is there a way to connect 2 tube preamps and switch between those versus a preamp and an actual amp head? 2. Can I use just one preamp with cyclops? I’m contemplating buying it so I can go into the line in of the power station and free up the effect loop since I’ve been going into the effects return of the PS2A direct from preamp.
1) Yes. Easily. 2) Yes, that's fine too.
@@FryetteAmps can you explain how to wire up the two preamps?
The PRS So called Hendrix amp sounds very unimpressive to my ears.
Fryette amps are the GOAT. No apologies. Play one if you get a chance.
Is the headphone amp in the unit analog or digital? Thanks,...
The audio signal path is all analog up to and after the IR cab cab generator.
As far as I am concerned, a smaller and lighter Deliverance is a Deliverance Synergy module in the Synergy SYN-30 head or the forthcoming SYN-20 head. Personally, I would rather run a SYN-1 chassis into a Fryette Power Station.
Will bad power tubes result in no volume in operate mode
That could be the issue. For more info, please contact [email protected]
Hello, when installing new pre amp tubes, what brand are you using these days....... I like your Hamer Guitar.............
We’ve used Shuguang a lot in the past. Now that they are available again, we’ll be using them where applicable. We also use JJ, Psvane and in some models, a Tung-Sol in V1.
I love the smell of hot tubes in the morning. In all seriousness, tube amps excite more of my human senses than just hearing. After playing a Pitbull, I found a top 3 most enjoyable life experience. Fryette Bass Guitar division when? 😂
Here is what is Bad Ass about this video folks... He Is Hot Switching The Speaker Output Between His Speaker and Load! And No Smoke Was Released In This Video...Damn Those Circuit Boards Are Sexy!