Пікірлер

• 
  @larschristensen33093 сағат бұрын

  The lever is not ment to be at the line but 13,5-14,5 mm below the Lines acc. to manual

• 
  @DieselDog19822 күн бұрын

  What kind of tune did you run afterwards?

• 
  @matthewplanner35422 күн бұрын

  Is it exactly the same for 1.9 sdi?

• 
  @liampreston33728 күн бұрын

  Hi tryed this but no luck so far put swivel on passenger seat but its a double do i need stronger resistor maybe ?

• 
  @StellaCadman-v4m10 күн бұрын

  Just watched how you stripped down the Renault Master for Radiator Replacement. Thanks for sharing your knowledge Jay, I now feel confident I can do the same job on my campervan which has just sprung a leak! Nice work, looking forward to watching more of your videos! 😎👍🛠

• 
  @wiganer991212 күн бұрын

  This is a safety recall by peugeot and will be done free of charge by any peugeot dealer

• 
  @chanhnguyen974012 күн бұрын

  Bad - Very BAD --- you did not show how to take the housing off & put them back on. Plus, you shown the old brake pads at 1 view toooooo long.

• 
  @BOBLFC113 күн бұрын

  what's the tool called for putting the thread in

• 
  @TheGrimStoic15 күн бұрын

  😀😀"bush-whakin alki piece of ..."

• 
  @tylerraines345118 күн бұрын

  Hi mate i changed ours and it seems to be leaking around but that screws into the housing? Ive done it up to 25nm as specs say new seal etc any help? Thanks

• 
  @fuelheadjay880018 күн бұрын

  @@tylerraines3451 have U damaged seal putting back in take It back out check it and is your torq rench been cal.me just nip it up by hand just tad more just to see if it stops if not you need to get new seal

• 
  @AnthonyHowell-z5t20 күн бұрын

  Hi mate, where did you order these from? I don’t like the ones that round off at the end, I like these

• 
  @tritonpressurewashing21 күн бұрын

  Any link for that solenoid? I can find the egr valve but not that sensor/solenoid

• 
  @tritonpressurewashing21 күн бұрын

  Very explicit video with so many useful details. Keep it up 👍

• 
  @Northerner12124 күн бұрын

  Twas hard to listen to him because he has bad asthma or summit . So the puffing and panting made it unclear at times.

• 
  @juliangreen-g3v24 күн бұрын

  Happy days mate looks well. Drop me a message if anyone requires 1 👍

• 
  @DaveShephard-o5s25 күн бұрын

  WASTE OF TIME THAT VID WAS!

• 
  @cpuuk28 күн бұрын

  Anyone got the part number for the S1? I ask as S1 and S2 are clearly not the same connector at the electrical end.

• 
  @jonjg6729 күн бұрын

  Hoping you can help. Have some vG20A carbs which are seized solid so replaced them with vg26vb carbs but can't figure out where the fuel lines run. Have the 2 off the 1&2 and 3&4 'fronts' which run into a T piece (can be seen at 15 mins in video) but there is a separate big fat fuel pipe running to the back of the carbs. Does this connect to the same fuel line from the fuel pump? Any help would be really appreciated. Thanks

• 
  @breadonbattyll1262Ай бұрын

  Hiya I saw you had some videos on a Matiz and I've got and issue where the abs light and the handbreak warning light won't go off. Me and my dad have chnaged the front abs sensors and the abs control unit (though that was a while ago now) but we've looked at everything we can think of but just cant seem to figure it out. Was just wondering what else might be worth looking at for either of them as we've got the MOT and at the moment it is likely to fail. Any help is very much appreciated as we are fully stuck. 😅

• 
  @72GLMАй бұрын

  Ayup mate, messaged you on here a few times, did you sell this in the end? Trying to buy some bits of a guy on FB, he's using pics of this bike? Cheers

• 
  @hotrodchris805Ай бұрын

  Cool swap. Whats the driving like? I have a 2005 Master and the steering feels very sensitive / fast. A smaller wheel would make it feel a little heavier ( no bad thing - its far from heavy) but im wondering if it'd make it even more sensitive / fast?

• 
  @MrAlexarassАй бұрын

  What kind of glue did you used?

• 
  @fuelheadjay8800Ай бұрын

  @@MrAlexarass Tiger seal

• 
  @shaunbarclaysentinal70Ай бұрын

  God video very useful and easy to follow thank you

• 
  @nathanjennings7026Ай бұрын

  What year is your bike because my bike is a 2004 and I can't find the oil plugs like the 2006 and up

• 
  @zeroshiea7525Ай бұрын

  don’t know if you will see this but if you do a reply would save my life! i need to know what parts i need i gotta re do my front suspension

• 
  @xVicissitudesxАй бұрын

  Tighten your sah up

• 
  @xVicissitudesxАй бұрын

  gaf

• 
  @projekt_no4Ай бұрын

  Hi! Had the cables replaced by a workshop (came in with a complete new engine btw..😂) and now the shifting is a bit “off” - I get 3rd gear instead of 5th, 2nd instead of 4th etc. Feels like the gear selector is a bit too much to the left or whatever. Do you think that’s what I can adjust with the orange clip? Would be great cause this really sucks 😂

• 
  @fuelheadjay8800Ай бұрын

  Yes should be able to

• 
  @LoftikazАй бұрын

  is air filter accessible for 1.6 blue hdi 2016?

• 
  @fuelheadjay8800Ай бұрын

  Yes

• 
  @2LittleDickieBirdsАй бұрын

  Great video in a confined space! Really didn't want to take the bumper off either

• 
  @memybikeni9931Ай бұрын

  Good easy mod, but how will you blank off the old one, assuming you don’t decide to start using the steering lock after 30 years 😂 I never give it a thought either tbh. I’m not a fan of the side mounted barrels really, always worried the key will fall out, but that’s the dangers of old bikes, new barrel should be ok for a few years anyway.

• 
  @fuelheadjay8800Ай бұрын

  Yer I be blanking or using it to mount new clocks through as trying to find new set of GPS clocks

• 
  @Eana-of-Sussex2 ай бұрын

  Where is a safe place to jack specifically a 535? No frame rails and a raised seam down the centre of the engine... does the whole bike rest on the thin engine casings? Theres no flat area underneath at all on a 535. The safest place seems to be up by the coil housing under the petrol tank but needs long rods to bolt into he frame and down to the jack....

• 
  @JoJanDiezel2 ай бұрын

  Great, thanks!

• 
  @GeorgeBurrows-vl1rj2 ай бұрын

  Any tips on changing timming belt on this engine,my small belt to the diesel pump has snaped,a cant see any way to lock it up or any timming marks ,any tips welcome ?

• 
  @tessandmax12 ай бұрын

  Hi brill videos but can u tell me what resistor i need as the plug is diferent on one i have got to swap thanks

• 
  @ralphcoolen84042 ай бұрын

  Shouldn't there be another rail especially for the cover plate?

• 
  @davidlord20092 ай бұрын

  Just wanted to say thanks from across the pond. Lol. That was great information on how to help me change the brakes on my Thunderbird.

• 
  @pascalchauvin23782 ай бұрын

  Bonjour un tutoriel pour changer les bougies sur Triumph Thunderbird storm merci

• 
  @Ein24042 ай бұрын

  So do they have any wear indication?? No squeak plates, no electric sensor...?

• 
  @-bollox2 ай бұрын

  No WD40 on the brake adjuster ? The handbrake cable looks too short it needs adjusting. Why not put new bearings in the new brake drums ? They don't cost much, and it won't last long like that. You can buy drums with bearings fitted TRW. Put grease on back plate where the shoes rub against for non binding operation.

• 
  @steveblount56642 ай бұрын

  I've done all the above but still can't remove ball joint.

• 
  @Chrisjones521112 ай бұрын

  Thanks for the demonstration.

• 
  @gaddafiaghakhan16772 ай бұрын

  Thanku pal

• 
  @mickyboy19552 ай бұрын

  Good vid....Thank you

• 
  @kylemole14553 ай бұрын

  Would pressure sense throw a code up?

• 
  @michaelbailey5543 ай бұрын

  Hi for some reason my air bag and service light stays on, even when put in machine to turn em off, any ideas m8 much apprectiated thanks mike

• 
  @fuelheadjay88002 ай бұрын

  Have you checked to make sure all plugs are in properly and not trapped and wires.and when reading fault it is saying steering wheel airbag.. if all fails try a resistor

• 
  @Eana-of-Sussex3 ай бұрын

  Hello there. Are you still riding this bike? How did the single carb hold up after using it for a while? Did you sort the manifold mounting issue?

• 
  @fuelheadjay88003 ай бұрын

  I sold the bike last year and up to then it was running fine and manifold I ended up sanding it till it matched up just right 👍

• 
  @tomsimmons82353 ай бұрын

  Tried it today on my van and it has worked a treat, thanks mate

• 
  @chatgogo3 ай бұрын

  Thank you for the video

• 
  @StephenAmoah-ds1lo3 ай бұрын

  E