First Time Jimmy, will take you on adventures of projects that I do not have any knowledge, very little knowledge, and jack of all trades knowledge. My Goal, is that you the viewer can in the end say, "I know I don't know how to do that; but, I feel I can take on the task of learning and doing it myself; now that I've seen Jimmy, do it for the First Time!" I feel each and everyone of you subscribing to my channel can accomplish ANYTHING!!!
Пікірлер
.....3rd s0000!://5 ¢√α
The videos are getting better!
Thank You, had issues with this one as well though. Battery on phone is on it's way out; so, I didn't record as much as I wanted to unfortunately :(
That machine is amazing! But is there something wrong with it, that vibration didn’t sound good?
LOL I was wondering if anyone would catch that! No nothing wrong😆 That sound is from my iPhone being tapped to the windshield; and you are hearing the vibration between the two! If you liked this video hit like and then subscribe to see more like videos and better camera work as this job moves along!
Do you have complet description of this thermal fuse ? Because on mine all the number are gone !
I'm pretty sure it's in the video, it's been a while since I installed.
Where did you get the fan fuse?
Hey I know it's been a while since this video had been up but I have a question where did you buy that unique pry bar? What's it called?
Harbor Freight Tie Rod Separator!
FYI, it’s a good Tie Rod separator as well😆
Oh I don’t know if you know this or not but the water heater would do the same thing and you can use those same fuses to replace. Awesome
Interesting, I did not know that! Hopefully, I won’t have to mess with that. But, if I have to, I do have the fuses😂
Thank you I need to replace the fuse for the fan
You’re Welcome 😊. Hopefully, this video helps you get it done!
@@firsttimejimmy9791 yes it did cause I didn’t even know a fuse existed. Grateful you popped up in my newsfeed and showed the problem and solution. I ordered the fuses from Amazon. Thanks again keep up the great useable content.
Just Saying, I watched a few of these videos on removing the steering wheel on a Boat, That being said , A ten Year old could have removed mine.
I had the same problem didn’t want to unbolt engine from transom too heavy and didn’t have a cherry picker .but thanks to your video .I replaced my cable but I used bolt cutters on cable .didn’t want sparks due to fuel tank . Thanks !
Bolt Cutter is definitely a good idea 💡!
You’re Welcome 😊. I’m glad I was able to help you think outside the box 🧐. Did you record it?
I am running mine port side,so with the connections facing port side,which connection should the cable go in top or bottom? Second I can't get the small tubing to lock in?Thanks for any info!
Did you use the pin provided or an Awl? An Awl (straight) will give you more pressure. Once you feel the the key way move, it will slide right in. Port side is how I hooked it up first!
I’m almost positive it was bottom because that was the easier way to get it in.
@@firsttimejimmy9791 Does it matter, as long as the steering is correct,that turning the wheel the boat goes in the same direction?Thanks again
@@paullozis9731 The hole definitely matters! If you watch this video or one of the other two where I put it in the wrong hole, I turned left and the boat turned right. I fixed it by switching holes. But, if you are saying you put it in a hole and you turn the steering wheel left and the boat goes left; we’ll then you have it in the right hole.
@@firsttimejimmy9791 Thanks for the information! 👍
Would like more like this
How did you remove the cable on the safe t?
There is a key that comes with the unit. It’s a circle with a pin that comes off of the circle. I think it’s called a Hitch Pin. Or you can take an Awl, and push in the designated hole and release the clamp from the steering cable end. The Awl gives you a lot more power to push in.
Glad you took my comments in the context intended. Again I appreciate your efforts and only intended to help.
You need to be talk a little more precise and do a little better with the camera, but thanks anyway.
Bob Stewart Thank You for the feedback. Camera work is in need of massive improvement for sure 😂. I’m working on some other videos now. All first time experiences; so, precise is tough. My channel is more for motivation that If I can do it, why not you? But, I’m sur as I get more videos published I’ll probably get better at being precise 🧐 Again Thank You for the feedback!